Add support for the Leadtek LTK028QV25BYL display panel
Subsystems (4)
cover Add support for the Leadtek LTK028QV25BYL display panel
Hi,
The Leadtek LTK08QV25BYL is a 2.8" 240x320 DSI display.
This series adds support for this device.
Best regards,
Hervé
Herve Codina (3):
dt-bindings: display: panel: Add the Leadtek LTK08QV25BYL panel drm/panel: Add support for the Leadtek LTK08QV25BYL panel
MAINTAINERS: Add the Leadtek LTK028QV25BYL panel driver entry
.../display/panel/leadtek,ltk028qv25byl.yaml | 55 ++++ MAINTAINERS | 7 + drivers/gpu/drm/panel/Kconfig | 12 + drivers/gpu/drm/panel/Makefile | 1 + .../drm/panel/panel-leadtek-ltk028qv25byl.c | 304 ++++++++++++++++++ 5 files changed, 379 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/leadtek,ltk028qv25byl.yaml create mode 100644 drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c
Signature · 1 line
2.51.0
PATCH 1/3 dt-bindings: display: panel: Add the Leadtek LTK08QV25BYL panel
The Leadtek LTK08QV25BYL is a 2.8" 240x320 DSI display.
--- .../display/panel/leadtek,ltk028qv25byl.yaml | 55 +++++++++++++++++++ 1 file changed, 55 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/leadtek,ltk028qv25byl.yaml
Documentation/devicetree/bindings/display/panel/leadtek,ltk028qv25byl.yaml new file +55 -0
@@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/leadtek,ltk028qv25byl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Leadtek LTK028QV25BYL 2.8in 240x320 DSI panel + +maintainers: + - Herve Codina <[email protected]> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: leadtek,ltk028qv25byl + + reg: + maxItems: 1 + + backlight: true + port: true + reset-gpios: true + + iovcc-supply: + description: regulator that supplies the IOVCC voltage + + vci-supply: + description: regulator that supplies the VCI voltage + +required: + - compatible + - reg + - backlight + - iovcc-supply + - vci-supply + +additionalProperties: false + +examples: + - | + dsi { + #address-cells = <1>; + #size-cells = <0>; + panel@0 { + compatible = "leadtek,ltk028qv25byl"; + reg = <0>; + backlight = <&backlight>; + iovcc-supply = <&vcc_1v8>; + vci-supply = <&vcc3v3_lcd>; + }; + }; + +...
Signature · 1 line
2.51.0
Re: [PATCH 1/3] dt-bindings: display: panel: Add the Leadtek LTK08QV25BYL panel
Quoted 3 lines · Herve Codina
The Leadtek LTK08QV25BYL is a 2.8" 240x320 DSI display.
Signed-off-by Herve Codina <[email protected]>
pw-bot: not-applicable
PATCH 2/3 drm/panel: Add support for the Leadtek LTK08QV25BYL panel
In reply to Herve CodinaThe Leadtek LTK08QV25BYL is a 2.8" 240x320 DSI display.
--- drivers/gpu/drm/panel/Kconfig | 12 + drivers/gpu/drm/panel/Makefile | 1 + .../drm/panel/panel-leadtek-ltk028qv25byl.c | 304 ++++++++++++++++++ 3 files changed, 317 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c
drivers/gpu/drm/panel/Kconfig +12 -0
@@ -367,6 +367,18 @@ config DRM_PANEL_KINGDISPLAY_KD097D04 24 bit RGB per pixel. It provides a MIPI DSI interface to the host and has a built-in LED backlight. +config DRM_PANEL_LEADTEK_LTK028QV25BYL + tristate "Leadtek LTK028QV25BYL panel" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for Leadtek LTK028QV25BYL + TFT-LCD modules. The panel has a 240x320 resolution and uses + 18 bit RGB per pixel. It provides a MIPI DSI interface to + the host and has a built-in LED backlight. + + config DRM_PANEL_LEADTEK_LTK050H3146W tristate "Leadtek LTK050H3146W panel" depends on OF
drivers/gpu/drm/panel/Makefile +1 -0
@@ -37,6 +37,7 @@ obj-$(CONFIG_DRM_PANEL_JDI_LPM102A188A) += panel-jdi-lpm102a188a.o obj-$(CONFIG_DRM_PANEL_JDI_R63452) += panel-jdi-fhd-r63452.o obj-$(CONFIG_DRM_PANEL_KHADAS_TS050) += panel-khadas-ts050.o obj-$(CONFIG_DRM_PANEL_KINGDISPLAY_KD097D04) += panel-kingdisplay-kd097d04.o +obj-$(CONFIG_DRM_PANEL_LEADTEK_LTK028QV25BYL) += panel-leadtek-ltk028qv25byl.o obj-$(CONFIG_DRM_PANEL_LEADTEK_LTK050H3146W) += panel-leadtek-ltk050h3146w.o obj-$(CONFIG_DRM_PANEL_LEADTEK_LTK500HD1829) += panel-leadtek-ltk500hd1829.o obj-$(CONFIG_DRM_PANEL_LINCOLNTECH_LCD197) += panel-lincolntech-lcd197.o
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c new file +304 -0
304 lines not on this page · raw message
Signature · 1 line
2.51.0
Neil Armstrong
maintainerRe: [PATCH 2/3] drm/panel: Add support for the Leadtek LTK08QV25BYL panel
Quoted 238 lines · Herve Codina
The Leadtek LTK08QV25BYL is a 2.8" 240x320 DSI display.
Signed-off-by Herve Codina <[email protected]>--- drivers/gpu/drm/panel/Kconfig | 12 + drivers/gpu/drm/panel/Makefile | 1 + .../drm/panel/panel-leadtek-ltk028qv25byl.c | 304 ++++++++++++++++++ 3 files changed, 317 insertions(+)create mode 100644
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.cdrivers/gpu/drm/panel/Kconfig +12
-0@@ -367,6 +367,18 @@ config DRM_PANEL_KINGDISPLAY_KD097D04 24 bit RGB per pixel. It provides a MIPI DSI interface to the host and has a built-in LED backlight. +config DRM_PANEL_LEADTEK_LTK028QV25BYL + tristate "Leadtek LTK028QV25BYL panel" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for Leadtek LTK028QV25BYL + TFT-LCD modules. The panel has a 240x320 resolution and uses + 18 bit RGB per pixel. It provides a MIPI DSI interface to + the host and has a built-in LED backlight. + + config DRM_PANEL_LEADTEK_LTK050H3146W tristate "Leadtek LTK050H3146W panel" depends on OFdrivers/gpu/drm/panel/Makefile +1
-0@@ -37,6 +37,7 @@ obj-$(CONFIG_DRM_PANEL_JDI_LPM102A188A) += panel-jdi-lpm102a188a.o obj-$(CONFIG_DRM_PANEL_JDI_R63452) += panel-jdi-fhd-r63452.o obj-$(CONFIG_DRM_PANEL_KHADAS_TS050) += panel-khadas-ts050.o obj-$(CONFIG_DRM_PANEL_KINGDISPLAY_KD097D04) += panel-kingdisplay-kd097d04.o +obj-$(CONFIG_DRM_PANEL_LEADTEK_LTK028QV25BYL) += panel-leadtek-ltk028qv25byl.o obj-$(CONFIG_DRM_PANEL_LEADTEK_LTK050H3146W) += panel-leadtek-ltk050h3146w.o obj-$(CONFIG_DRM_PANEL_LEADTEK_LTK500HD1829) += panel-leadtek-ltk500hd1829.o obj-$(CONFIG_DRM_PANEL_LINCOLNTECH_LCD197) += panel-lincolntech-lcd197.odrivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c new file +187
-0@@ -0,0 +1,304 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Leadtek LTK08QV25BYL 2.8" MIPI-DSI panel driver +* Copyright (c) 2025, Bootlin +* +* base on panel-leadtek-ltk050h346w.c +* Copyright (C) 2020 Theobroma Systems Design und Consulting GmbH +*/ + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/regulator/consumer.h> + +#include <video/mipi_display.h> + +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> + +struct ltk028qv25byl { +struct device *dev; +struct drm_panel panel; +struct gpio_desc *reset_gpio; +struct regulator *vci; +struct regulator *iovcc; +}; + +static inline struct ltk028qv25byl *panel_to_ltk028qv25byl (struct drm_panel *panel) +{ + return container_of(panel, struct ltk028qv25byl, panel); +} + +static int ltk028qv25byl_init_sequence (struct ltk028qv25byl *ctx) +{ +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +struct mipi_dsi_multi_context dsi_ctx = { .dsi = dsi }; + +/* +* Init sequence was supplied by the panel vendor. All documentation +* provided by the vendor (i.e comments in the provided init sequence) +* is also given here as comments without modification. +*/ + +/* Password */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xdf ,0x98 ,0x51 ,0xe9 ); + +/* Page 0 */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xde ,0x00 ); + +/* VGMP, VGSP, VGMN, VGSN 4.3 */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xb7 ,0x1e ,0x85 ,0x1e ,0x33 ); + +/* Set_R_GAMMA */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xc8 ,0x3f ,0x2e ,0x25 ,0x21 ,0x23 , +0x25 ,0x1f ,0x1e ,0x1c ,0x1b ,0x19 ,0x11 , +0x0e ,0x0a ,0x06 ,0x0e ,0x3f ,0x2e ,0x26 , +0x21 ,0x24 ,0x25 ,0x1f ,0x1f ,0x1d ,0x1c , +0x19 ,0x11 ,0x0e ,0x0a ,0x06 ,0x0e ); + +/* POW_CTRL */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xb9 ,0x33 ,0x08 ,0xcc ); + +/* DCDC_SEL */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xbb ,0x44 ,0x7a ,0x30 ,0x40 ,0x7c , +0x60 ,0x70 ,0x70 ); + +/* VDD_CTRL */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xbc ,0x38 ,0x3c ); + +/* SETSTBA */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xc0 ,0x31 ,0x20 ); + +/* SETPANEL(default) */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xc1 ,0x12 ); + +/* SETRGBCYC */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xc3 ,0x08 ,0x00 ,0x0a ,0x10 ,0x08 , +0x54 ,0x45 ,0x71 ,0x2c ); + +/* SETRGBCYC(default) */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xc4 ,0x00 ,0xa0 ,0x79 ,0x0e ,0x0a , +0x16 ,0x79 ,0x0e ,0x0a ,0x16 ,0x79 ,0x0e , +0x0a ,0x16 ,0x82 ,0x00 ,0x03 ); + +/* SET_GD(default) */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xd0 ,0x04 ,0x0c ,0x6a ,0x0f ,0x00 ,0x03 ); + +/* RAMCTRL(default) */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xd7 ,0x13 ,0x00 ); + +/* Page 2 */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xde ,0x02 ); + +/* DCDC_SET */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xb8 ,0x1d ,0xa0 ,0x2f ,0x2c ,0x2b ); + +/* SETRGBCYC2 */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xc1 ,0x10 ,0x66 ,0x66 ,0x01 ); + +/* Page 0 */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xde ,0x00 ); + +/* SLPOUT + 120ms delay */ +mipi_dsi_dcs_exit_sleep_mode_multi (&dsi_ctx); +mipi_dsi_msleep (&dsi_ctx,120 ); + +/* Page 2 */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xde ,0x02 ); + +/* OSCM */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xc5 ,0x4e ,0x00 ,0x00 ); + +/* SETMIPI_2 */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xca ,0x30 ,0x20 ,0xf4 ); + +/* Page 4 */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xde ,0x04 ); + +/* SETPHY3 */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xd3 ,0x3c ); + +/* Page 0 */ +mipi_dsi_dcs_write_seq_multi (&dsi_ctx,0xde ,0x00 ); + +/* Display on + 20ms delay */ +mipi_dsi_dcs_set_display_on_multi (&dsi_ctx); +mipi_dsi_msleep (&dsi_ctx,20 ); + +return dsi_ctx.accum_err; +} + +static int ltk028qv25byl_unprepare (struct drm_panel *panel) +{ +struct ltk028qv25byl *ctx =panel_to_ltk028qv25byl (panel); +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +struct mipi_dsi_multi_context dsi_ctx = { .dsi = dsi }; + +mipi_dsi_dcs_set_display_off_multi (&dsi_ctx); +mipi_dsi_dcs_enter_sleep_mode_multi (&dsi_ctx); +if (dsi_ctx.accum_err) +return dsi_ctx.accum_err; + +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); + +regulator_disable (ctx->iovcc); +regulator_disable (ctx->vci); + +return 0 ; +} + +static int ltk028qv25byl_prepare (struct drm_panel *panel) +{ +struct ltk028qv25byl *ctx =panel_to_ltk028qv25byl (panel); +int ret; + + ret =regulator_enable (ctx->vci); +if (ret <0 ) { +dev_err (ctx->dev,"Failed to enable vcc supply (%d)\n" , ret); +return ret; + } + ret =regulator_enable (ctx->iovcc); +if (ret <0 ) { +dev_err (ctx->dev,"Failed to enable iovcc supply (%d)\n" , ret); + goto disable_vci; + } + +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); +usleep_range (5000 ,6000 ); +gpiod_set_value_cansleep (ctx->reset_gpio,0 ); +msleep (20 ); + + ret =ltk028qv25byl_init_sequence (ctx); +if (ret) + goto force_reset; + +return 0 ; + +force_reset: +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); +regulator_disable (ctx->iovcc); +disable_vci: +regulator_disable (ctx->vci); +return ret; +} +
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c line 197
Quoted 10 lines
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c new file +10
-0+static const struct drm_display_mode ltk028qv25byl_mode = { + .hdisplay =240 , + .hsync_start =240 +120 , + .hsync_end =240 +120 +4 , + .htotal =240 +120 +4 +120 , + .vdisplay =320 , + .vsync_start =320 +8 , + .vsync_end =320 +8 +2 , + .vtotal =320 +8 +2 +6 , + .clock =10000000 /1000 ,
Usually we calculate the clock from the mode parameters, won't it work here ?
Quoted 46 lines
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c new file +46
-0+ .flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC, + .width_mm = 45, + .height_mm = 62, +}; + +static int ltk028qv25byl_get_modes (struct drm_panel *panel, +struct drm_connector *connector) +{ +struct drm_display_mode *mode; + + mode =drm_mode_duplicate (connector->dev, <k028qv25byl_mode); +if (!mode) +return -ENOMEM ; + +drm_mode_set_name (mode); + + mode->type =DRM_MODE_TYPE_DRIVER |DRM_MODE_TYPE_PREFERRED ; + connector->display_info.width_mm = mode->width_mm; + connector->display_info.height_mm = mode->height_mm; +drm_mode_probed_add (connector, mode); + +return 1 ; +} + +static const struct drm_panel_funcs ltk028qv25byl_funcs = { + .unprepare = ltk028qv25byl_unprepare, + .prepare = ltk028qv25byl_prepare, + .get_modes = ltk028qv25byl_get_modes, +}; + +static int ltk028qv25byl_probe (struct mipi_dsi_device *dsi) +{ +struct device *dev = &dsi->dev; +struct ltk028qv25byl *ctx; +int ret; + + ctx =devm_drm_panel_alloc (dev,__typeof (*ctx), panel, + <k028qv25byl_funcs, +DRM_MODE_CONNECTOR_DSI ); +if (IS_ERR (ctx)) +return PTR_ERR (ctx); + + ctx->reset_gpio =devm_gpiod_get_optional (dev,"reset" ,GPIOD_OUT_LOW ); +if (IS_ERR (ctx->reset_gpio)) +return dev_err_probe (dev,PTR_ERR (ctx->reset_gpio), +"Failed to get reset gpio\n" );
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c line 253
Quoted 10 lines
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c new file +10
-0+ + ctx->vci =devm_regulator_get (dev,"vci" ); +if (IS_ERR (ctx->vci)) +return dev_err_probe (dev,PTR_ERR (ctx->vci), +"Failed to get vcc regulator\n" ); + + ctx->iovcc =devm_regulator_get (dev,"iovcc" ); +if (IS_ERR (ctx->iovcc)) +return dev_err_probe (dev,PTR_ERR (ctx->iovcc), +"Failed to get iovcc regulator\n" );
Can you switch to devm_regulator_bulk_get_const() ?
Quoted 41 lines
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c new file +41
-0+ +mipi_dsi_set_drvdata (dsi, ctx); + + ctx->dev = dev; + + dsi->lanes =1 ; + dsi->format =MIPI_DSI_FMT_RGB888 ; + dsi->mode_flags =MIPI_DSI_MODE_VIDEO |MIPI_DSI_MODE_VIDEO_BURST | +MIPI_DSI_MODE_LPM |MIPI_DSI_MODE_NO_EOT_PACKET ; + + ret =drm_panel_of_backlight (&ctx->panel); +if (ret) +return ret; + +drm_panel_add (&ctx->panel); + + ret =devm_mipi_dsi_attach (dev, dsi); +if (ret <0 ) { +drm_panel_remove (&ctx->panel); +return dev_err_probe (dev, ret,"Failed to attach to DSI host\n" ); + } + +return 0 ; +} + +static void ltk028qv25byl_remove (struct mipi_dsi_device *dsi) +{ +struct ltk028qv25byl *ctx =mipi_dsi_get_drvdata (dsi); + +drm_panel_remove (&ctx->panel); +} + +static const struct of_device_id ltk028qv25byl_of_match[] = { + { .compatible ="leadtek,ltk028qv25byl" }, + {/* sentinel */ } +}; +MODULE_DEVICE_TABLE (of, ltk028qv25byl_of_match); + +static struct mipi_dsi_driver ltk028qv25byl_driver = { + .driver = { + .name ="panel-leadtek-ltk028qv25byl" ,
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c line 304
Quoted 10 lines
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c new file +10
-0+ .of_match_table = ltk028qv25byl_of_match, + }, + .probe = ltk028qv25byl_probe, + .remove = ltk028qv25byl_remove, +}; +module_mipi_dsi_driver (ltk028qv25byl_driver); + +MODULE_AUTHOR ("Herve Codina <[email protected]>" ); +MODULE_DESCRIPTION ("DRM driver for Leadtek LTK028QV25BYL MIPI DSI panel" ); +MODULE_LICENSE ("GPL" );
Thanks,
Neil
Re: [PATCH 2/3] drm/panel: Add support for the Leadtek LTK08QV25BYL panel
Hi Neil,
On Wed, 29 Oct 2025 21:45:24 +0100
Neil Armstrong <[email protected]> wrote:
...
Quoted 5 lines
Quoted 5 lines
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c new file +5
-0+ +static const struct drm_display_mode ltk028qv25byl_mode = { + .hdisplay =240 , + .hsync_start =240 +120 , + .hsync_end =240 +120 +4 ,
Quoted 9 lines
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c line 197
Quoted 6 lines
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c new file +6
-0+ .htotal = 240 + 120 + 4 + 120, + .vdisplay = 320, + .vsync_start = 320 + 8, + .vsync_end = 320 + 8 + 2, + .vtotal = 320 + 8 + 2 + 6, + .clock = 10000000 / 1000,Usually we calculate the clock from the mode parameters, won't it work here ?
The panel has an internal oscillator an the data transfer need to be sync with this oscillator.
10M pixel per sec is the value set by the vendor.
I tried to use a value based on other mode parameters such as
(240 + 120 + 4 + 120) * (320 + 8 + 2 + 6) * 60 / 1000
and it didn't work. I also tried ' ... * 90 / 1000) and ' ... * 100 / 1000) without better results.
I can add a comment if you want in the next iteration to spot the value:
--- 8< ---
.clock = 10000000 / 1000, /* 10 Mbps, internal panel oscillator */
--- 8< ---
Let me know.
...
Quoted 6 lines
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c line 253
Quoted 4 lines
drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c new file +4
-0+ ctx->iovcc =devm_regulator_get (dev,"iovcc" ); +if (IS_ERR (ctx->iovcc)) +return dev_err_probe (dev,PTR_ERR (ctx->iovcc), +"Failed to get iovcc regulator\n" );Can you switch to
devm_regulator_bulk_get_const()?
Yes, I will do that in the next iteration.
Best regards,
Hervé
PATCH 3/3 MAINTAINERS: Add the Leadtek LTK028QV25BYL panel driver entry
In reply to Herve CodinaAfter contributing the driver, add myself as the maintainer for the Leadtek LTK028QV25BYL panel driver.
--- MAINTAINERS | 7 +++++++ 1 file changed, 7 insertions(+)
MAINTAINERS +7 -0
@@ -7811,6 +7811,13 @@ S: Maintained F: Documentation/devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml F: drivers/gpu/drm/panel/panel-jadard-jd9365da-h3.c +DRM DRIVER FOR LEADTEK LTK028QV25BYL PANELS +M: Herve Codina <[email protected]> +S: Maintained +T: git https://gitlab.freedesktop.org/drm/misc/kernel.git +F: Documentation/devicetree/bindings/display/panel/leadtek,ltk028qv25byl.yaml +F: drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c + DRM DRIVER FOR LG SW43408 PANELS M: Sumit Semwal <[email protected]> M: Casey Connolly <[email protected]>
Signature · 1 line
2.51.0
Re: [PATCH 3/3] MAINTAINERS: Add the Leadtek LTK028QV25BYL panel driver entry
Quoted 16 lines · Herve Codina
After contributing the driver, add myself as the maintainer for the Leadtek LTK028QV25BYL panel driver.
Signed-off-by Herve Codina <[email protected]>--- MAINTAINERS | 7 +++++++ 1 file changed, 7 insertions(+)MAINTAINERS +0
-0@@ -7811,6 +7811,13 @@ S: Maintained F: Documentation/devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml F: drivers/gpu/drm/panel/panel-jadard-jd9365da-h3.c
MAINTAINERS S: Maintained · line 7823
Quoted 10 lines
MAINTAINERS +7
-0+DRM DRIVER FOR LEADTEK LTK028QV25BYL PANELS +M: Herve Codina <[email protected]> +S: Maintained +T: git https://gitlab.freedesktop.org/drm/misc/kernel.git +F: Documentation/devicetree/bindings/display/panel/leadtek,ltk028qv25byl.yaml +F: drivers/gpu/drm/panel/panel-leadtek-ltk028qv25byl.c + DRM DRIVER FOR LG SW43408 PANELS M: Sumit Semwal <[email protected]> M: Casey Connolly <[email protected]>