Skip to contentSkip to conversation

pinctrl: mcp23s08: init reg_defaults from HW at probe and switch cache type

PATCH In review [email protected] 3 participants 4 messages Oct 27, 2025 – Oct 29, 2025

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 pinctrl: mcp23s08: init reg_defaults from HW at probe and switch cache type

From: Maksim Kiselev <[email protected]>

The probe function does not guarantee that chip registers are in their default state. Thus using reg_defaults for regmap is incorrect.

For example, the chip may have already been configured by the bootloader before the Linux driver loads, or the mcp might not have a reset at all and not reset a state between reboots.

In such cases, using reg_defaults leads to the cache values diverging from the actual registers values in the chip.

Previous attempts to fix consequences of this issue were made in 'commit 3ede3f8b4b4b ("pinctrl: mcp23s08: Reset all pins to input at probe")', but this is insufficient. The OLAT register reset is also required. And there's still potential for new issues arising due to cache desynchronization of other registers.

Therefore, remove reg_defaults and provide num_reg_defaults_raw. In that case the cache defaults being initialized from hardware.

Also switch cache type to REGCACHE_MAPLE, which is aware of (in)valid cache entries.

And remove the force reset all pins to input at probe as it is no longer required.

---
 drivers/pinctrl/pinctrl-mcp23s08.c | 40 +++---------------------------
 1 file changed, 4 insertions(+), 36 deletions(-)
drivers/pinctrl/pinctrl-mcp23s08.c +4 -36
index 78ff7930649d..edda2893945d 100644
@@ -44,17 +44,6 @@
 #define MCP_GPIO	0x09
 #define MCP_OLAT	0x0a
 
-static const struct reg_default mcp23x08_defaults[] = {
-	{.reg = MCP_IODIR,		.def = 0xff},
-	{.reg = MCP_IPOL,		.def = 0x00},
-	{.reg = MCP_GPINTEN,		.def = 0x00},
-	{.reg = MCP_DEFVAL,		.def = 0x00},
-	{.reg = MCP_INTCON,		.def = 0x00},
-	{.reg = MCP_IOCON,		.def = 0x00},
-	{.reg = MCP_GPPU,		.def = 0x00},
-	{.reg = MCP_OLAT,		.def = 0x00},
-};
-
 static const struct regmap_range mcp23x08_volatile_range = {
 	.range_min = MCP_INTF,
 	.range_max = MCP_GPIO,
@@ -82,25 +71,13 @@ const struct regmap_config mcp23x08_regmap = {
 	.reg_stride = 1,
 	.volatile_table = &mcp23x08_volatile_table,
 	.precious_table = &mcp23x08_precious_table,
-	.reg_defaults = mcp23x08_defaults,
-	.num_reg_defaults = ARRAY_SIZE(mcp23x08_defaults),
-	.cache_type = REGCACHE_FLAT,
+	.num_reg_defaults_raw = MCP_OLAT + 1,
+	.cache_type = REGCACHE_MAPLE,
 	.max_register = MCP_OLAT,
 	.disable_locking = true, /* mcp->lock protects the regmap */
 };
 EXPORT_SYMBOL_GPL(mcp23x08_regmap);
 
-static const struct reg_default mcp23x17_defaults[] = {
-	{.reg = MCP_IODIR << 1,		.def = 0xffff},
-	{.reg = MCP_IPOL << 1,		.def = 0x0000},
-	{.reg = MCP_GPINTEN << 1,	.def = 0x0000},
-	{.reg = MCP_DEFVAL << 1,	.def = 0x0000},
-	{.reg = MCP_INTCON << 1,	.def = 0x0000},
-	{.reg = MCP_IOCON << 1,		.def = 0x0000},
-	{.reg = MCP_GPPU << 1,		.def = 0x0000},
-	{.reg = MCP_OLAT << 1,		.def = 0x0000},
-};
-
 static const struct regmap_range mcp23x17_volatile_range = {
 	.range_min = MCP_INTF << 1,
 	.range_max = MCP_GPIO << 1,
@@ -129,9 +106,8 @@ const struct regmap_config mcp23x17_regmap = {
 	.max_register = MCP_OLAT << 1,
 	.volatile_table = &mcp23x17_volatile_table,
 	.precious_table = &mcp23x17_precious_table,
-	.reg_defaults = mcp23x17_defaults,
-	.num_reg_defaults = ARRAY_SIZE(mcp23x17_defaults),
-	.cache_type = REGCACHE_FLAT,
+	.num_reg_defaults_raw = MCP_OLAT + 1,
+	.cache_type = REGCACHE_MAPLE,
 	.val_format_endian = REGMAP_ENDIAN_LITTLE,
 	.disable_locking = true, /* mcp->lock protects the regmap */
 };
@@ -614,14 +590,6 @@ int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev,
 
 	mcp->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
 
-	/*
-	 * Reset the chip - we don't really know what state it's in, so reset
-	 * all pins to input first to prevent surprises.
-	 */
-	ret = mcp_write(mcp, MCP_IODIR, mcp->chip.ngpio == 16 ? 0xFFFF : 0xFF);
-	if (ret < 0)
-		return ret;
-
 	/* verify MCP_IOCON.SEQOP = 0, so sequential reads work,
 	 * and MCP_IOCON.HAEN = 1, so we work with all chips.
 	 */
Signature · 1 line
2.48.1
#1 lore raw
Quoted 20 lines · On Mon, Oct 27, 2025 at 01:46:26PM +0300, [email protected] wrote:

The probe function does not guarantee that chip registers are in their default state. Thus using reg_defaults for regmap is incorrect.

For example, the chip may have already been configured by the bootloader before the Linux driver loads, or the mcp might not have a reset at all and not reset a state between reboots.

In such cases, using reg_defaults leads to the cache values diverging from the actual registers values in the chip.

Previous attempts to fix consequences of this issue were made in 'commit 3ede3f8b4b4b ("pinctrl: mcp23s08: Reset all pins to input at probe")', but this is insufficient. The OLAT register reset is also required. And there's still potential for new issues arising due to cache desynchronization of other registers.

Therefore, remove reg_defaults and provide num_reg_defaults_raw. In that case the cache defaults being initialized from hardware.

Quoted 7 lines

Also switch cache type to REGCACHE_MAPLE, which is aware of (in)valid cache entries.

And remove the force reset all pins to input at probe as it is no longer required.

---

No changelog? No need to resend, just reply with the missing piece.

Quoted 2 lines
 drivers/pinctrl/pinctrl-mcp23s08.c | 40 +++---------------------------
 1 file changed, 4 insertions(+), 36 deletions(-)
Signature · 2 lines
With Best Regards,
Andy Shevchenko
#2 lore raw

Hi !

пн, 27 окт. 2025 г. в 14:49, Andy Shevchenko
<[email protected]>:

Quoted 25 lines · On Mon, Oct 27, 2025 at 01:46:26PM +0300, [email protected] wrote:
Quoted 23 lines

The probe function does not guarantee that chip registers are in their default state. Thus using reg_defaults for regmap is incorrect.

For example, the chip may have already been configured by the bootloader before the Linux driver loads, or the mcp might not have a reset at all and not reset a state between reboots.

In such cases, using reg_defaults leads to the cache values diverging from the actual registers values in the chip.

Previous attempts to fix consequences of this issue were made in 'commit 3ede3f8b4b4b ("pinctrl: mcp23s08: Reset all pins to input at probe")', but this is insufficient. The OLAT register reset is also required. And there's still potential for new issues arising due to cache desynchronization of other registers.

Therefore, remove reg_defaults and provide num_reg_defaults_raw. In that case the cache defaults being initialized from hardware.

Also switch cache type to REGCACHE_MAPLE, which is aware of (in)valid cache entries.

Quoted 6 lines
Quoted 4 lines

And remove the force reset all pins to input at probe as it is no longer required.

---

No changelog? No need to resend, just reply with the missing piece.

Sorry, my bad.

Changelog:
v3:
- changed cache type from REGCACHE_FLAT to REGCACHE_MAPLE
- added .num_reg_defaults_raw to init regs cache from HW at probe

v2:
- rollback v1 changes
- dropped .reg_defaults of mcp23x regmaps
- dropped reset all pins to input at probe (commit 3ede3f8b4b4b)

Quoted 9 lines
Quoted 3 lines
 drivers/pinctrl/pinctrl-mcp23s08.c | 40 +++---------------------------
 1 file changed, 4 insertions(+), 36 deletions(-)

--
With Best Regards,
Andy Shevchenko

#3 lore raw
Quoted 9 lines · Maxim Kiselev

Changelog:
v3:
- changed cache type from REGCACHE_FLAT to REGCACHE_MAPLE
- added .num_reg_defaults_raw to init regs cache from HW at probe

v2:
- rollback v1 changes
- dropped .reg_defaults of mcp23x regmaps
- dropped reset all pins to input at probe (commit 3ede3f8b4b4b)

It'd be great if I could get some ACKs/R-Bs and/or Tested-by:s on this patch.

Is this fixes (for-v6.18) material or is v6.19 fine?

I'm good with putting it in queue for v6.19 but for fixes I would really like a few tested-by:s given how widely this driver is used.

Yours,
Linus Walleij