Skip to contentSkip to conversation

Bluetooth: btrtl: Avoid loading the config file on security chips

PATCH Applied Max Chou 4 participants 4 messages Nov 5, 2025 – Nov 11, 2025 Bluetooth drivers

lore
Share & tools
lore

Max Chou

author
#0 lore raw

PATCH v2 1/1 Bluetooth: btrtl: Avoid loading the config file on security chips

For chips with security enabled, it's only possible to load firmware with a valid signature pattern.
If key_id is not zero, it indicates a security chip, and the driver will not load the config file.

- Example log for a security chip.

Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a
lmp_ver=0c lmp_subver=8922
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: btrtl_initialize: key id 1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin
Bluetooth: hci0: RTL: cfg_sz 0, total sz 71301
Bluetooth: hci0: RTL: fw version 0x41c0c905

- Example log for a normal chip.

Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a
lmp_ver=0c lmp_subver=8922
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: btrtl_initialize: key id 0
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_config.bin
Bluetooth: hci0: RTL: cfg_sz 6, total sz 71307
Bluetooth: hci0: RTL: fw version 0x41c0c905

---
Changes in V2:
- Print key_id at INFO level
- Update commit information for key_id based on review suggestions

---
 drivers/bluetooth/btrtl.c | 24 +++++++++++++-----------
 1 file changed, 13 insertions(+), 11 deletions(-)
drivers/bluetooth/btrtl.c +13 -11
index 8290932b8f7b..5603b282f9bc 100644
@@ -50,7 +50,7 @@
 
 #define	RTL_CHIP_SUBVER (&(struct rtl_vendor_cmd) {{0x10, 0x38, 0x04, 0x28, 0x80}})
 #define	RTL_CHIP_REV    (&(struct rtl_vendor_cmd) {{0x10, 0x3A, 0x04, 0x28, 0x80}})
-#define	RTL_SEC_PROJ    (&(struct rtl_vendor_cmd) {{0x10, 0xA4, 0x0D, 0x00, 0xb0}})
+#define	RTL_SEC_PROJ    (&(struct rtl_vendor_cmd) {{0x10, 0xA4, 0xAD, 0x00, 0xb0}})
 
 #define RTL_PATCH_SNIPPETS		0x01
 #define RTL_PATCH_DUMMY_HEADER		0x02
@@ -544,7 +544,6 @@ static int rtlbt_parse_firmware_v2(struct hci_dev *hdev,
 {
 	struct rtl_epatch_header_v2 *hdr;
 	int rc;
-	u8 reg_val[2];
 	u8 key_id;
 	u32 num_sections;
 	struct rtl_section *section;
@@ -559,14 +558,7 @@ static int rtlbt_parse_firmware_v2(struct hci_dev *hdev,
 		.len  = btrtl_dev->fw_len - 7, /* Cut the tail */
 	};
 
-	rc = btrtl_vendor_read_reg16(hdev, RTL_SEC_PROJ, reg_val);
-	if (rc < 0)
-		return -EIO;
-	key_id = reg_val[0];
-
-	rtl_dev_dbg(hdev, "%s: key id %u", __func__, key_id);
-
-	btrtl_dev->key_id = key_id;
+	key_id = btrtl_dev->key_id;
 
 	hdr = rtl_iov_pull_data(&iov, sizeof(*hdr));
 	if (!hdr)
@@ -1081,6 +1073,8 @@ struct btrtl_device_info *btrtl_initialize(struct hci_dev *hdev,
 	u16 hci_rev, lmp_subver;
 	u8 hci_ver, lmp_ver, chip_type = 0;
 	int ret;
+	int rc;
+	u8 key_id;
 	u8 reg_val[2];
 
 	btrtl_dev = kzalloc(sizeof(*btrtl_dev), GFP_KERNEL);
@@ -1191,6 +1185,14 @@ struct btrtl_device_info *btrtl_initialize(struct hci_dev *hdev,
 		goto err_free;
 	}
 
+	rc = btrtl_vendor_read_reg16(hdev, RTL_SEC_PROJ, reg_val);
+	if (rc < 0)
+		goto err_free;
+
+	key_id = reg_val[0];
+	btrtl_dev->key_id = key_id;
+	rtl_dev_info(hdev, "%s: key id %u", __func__, key_id);
+
 	btrtl_dev->fw_len = -EIO;
 	if (lmp_subver == RTL_ROM_LMP_8852A && hci_rev == 0x000c) {
 		snprintf(fw_name, sizeof(fw_name), "%s_v2.bin",
@@ -1213,7 +1215,7 @@ struct btrtl_device_info *btrtl_initialize(struct hci_dev *hdev,
 		goto err_free;
 	}
 
-	if (btrtl_dev->ic_info->cfg_name) {
+	if (btrtl_dev->ic_info->cfg_name && !btrtl_dev->key_id) {
 		if (postfix) {
 			snprintf(cfg_name, sizeof(cfg_name), "%s-%s.bin",
 				 btrtl_dev->ic_info->cfg_name, postfix);
Signature · 1 line
2.43.0
#1 lore raw

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list. This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=1019859

---Test result---

Test Summary:

CheckPatch                    PENDING   0.44 seconds
GitLint                       PENDING   0.39 seconds
SubjectPrefix                 PASS      0.06 seconds
BuildKernel                   PASS      25.17 seconds
CheckAllWarning               PASS      27.24 seconds
CheckSparse                   PASS      30.83 seconds
BuildKernel32                 PASS      24.65 seconds
TestRunnerSetup               PASS      492.14 seconds
TestRunner_l2cap-tester       PASS      23.33 seconds
TestRunner_iso-tester         PASS      95.34 seconds
TestRunner_bnep-tester        PASS      5.98 seconds
TestRunner_mgmt-tester        FAIL      118.52 seconds
TestRunner_rfcomm-tester      PASS      9.09 seconds
TestRunner_sco-tester         PASS      14.24 seconds
TestRunner_ioctl-tester       PASS      9.71 seconds
TestRunner_mesh-tester        FAIL      11.74 seconds
TestRunner_smp-tester         PASS      8.40 seconds
TestRunner_userchan-tester    PASS      6.38 seconds
IncrementalBuild              PENDING   1.11 seconds

Details
##############################
Test: CheckPatch - PENDING
Desc: Run checkpatch.pl script Output:

##############################
Test: GitLint - PENDING
Desc: Run gitlint
Output:

##############################
Test: TestRunner_mgmt-tester - FAIL
Desc: Run mgmt-tester with test-runner Output:
Total: 490, Passed: 485 (99.0%), Failed: 1, Not Run: 4

Failed Test Cases
Read Exp Feature - Success Failed 0.102 seconds
##############################
Test: TestRunner_mesh-tester - FAIL
Desc: Run mesh-tester with test-runner Output:
Total: 10, Passed: 8 (80.0%), Failed: 2, Not Run: 0

Failed Test Cases

Mesh - Send cancel - 1                               Timed out    2.380 seconds
Mesh - Send cancel - 2                               Timed out    1.996 seconds

##############################
Test: IncrementalBuild - PENDING
Desc: Incremental build with the patches in the series Output:

---
Regards,
Linux Bluetooth

#2 lore raw
In reply to Max Chou
This patch was applied to bluetooth/bluetooth-next.git (master) by Luiz Augusto von Dentz <[email protected]>:

Hello:

This patch was applied to bluetooth/bluetooth-next.git (master) by Luiz Augusto von Dentz <[email protected]>:

Quoted 8 lines · On Wed, 5 Nov 2025 20:02:04 +0800 you wrote:

For chips with security enabled, it's only possible to load firmware with a valid signature pattern.
If key_id is not zero, it indicates a security chip, and the driver will not load the config file.

- Example log for a security chip.

[...]

Here is the summary with links:
- [v2] Bluetooth: btrtl: Avoid loading the config file on security chips

    https://git.kernel.org/bluetooth/bluetooth-next/c/9063119bdaee

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html
Reviewed-by on v2 1/1
#3 lore raw
In reply to Max Chou

Dear Max,

Thank you for your patch. I respond despite your patch already been committed.

Am 05.11.25 um 13:02 schrieb Max Chou:

Quoted 9 lines

For chips with security enabled, it's only possible to load firmware with a valid signature pattern.
If key_id is not zero, it indicates a security chip, and the driver will not load the config file.

- Example log for a security chip.

Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a
lmp_ver=0c lmp_subver=8922

No linebreak needed for pasted lines.

Quoted 2 lines

Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: btrtl_initialize: key id 1

Maybe you could send a follow-up to make that line more informative by also printing, that this chip runs in security mode.

Quoted 88 lines

Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin
Bluetooth: hci0: RTL: cfg_sz 0, total sz 71301
Bluetooth: hci0: RTL: fw version 0x41c0c905

- Example log for a normal chip.

Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a
lmp_ver=0c lmp_subver=8922
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: btrtl_initialize: key id 0
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_config.bin
Bluetooth: hci0: RTL: cfg_sz 6, total sz 71307
Bluetooth: hci0: RTL: fw version 0x41c0c905

---
Changes in V2:
- Print key_id at INFO level
- Update commit information for key_id based on review suggestions

---
  drivers/bluetooth/btrtl.c | 24 +++++++++++++-----------
  1 file changed, 13 insertions(+), 11 deletions(-)
drivers/bluetooth/btrtl.c +12 -10
index 8290932b8f7b..5603b282f9bc 100644
@@ -50,7 +50,7 @@
 
  #define	RTL_CHIP_SUBVER (&(struct rtl_vendor_cmd) {{0x10, 0x38, 0x04, 0x28, 0x80}})
  #define	RTL_CHIP_REV    (&(struct rtl_vendor_cmd) {{0x10, 0x3A, 0x04, 0x28, 0x80}})
-#define	RTL_SEC_PROJ    (&(struct rtl_vendor_cmd) {{0x10, 0xA4, 0x0D, 0x00, 0xb0}})
+#define	RTL_SEC_PROJ    (&(struct rtl_vendor_cmd) {{0x10, 0xA4, 0xAD, 0x00, 0xb0}})
 
  #define RTL_PATCH_SNIPPETS		0x01
  #define RTL_PATCH_DUMMY_HEADER		0x02
@@ -544,7 +544,6 @@ static int rtlbt_parse_firmware_v2(struct hci_dev *hdev,
  {
  	struct rtl_epatch_header_v2 *hdr;
  	int rc;
-	u8 reg_val[2];
  	u8 key_id;
  	u32 num_sections;
  	struct rtl_section *section;
@@ -559,14 +558,7 @@ static int rtlbt_parse_firmware_v2(struct hci_dev *hdev,
  		.len  = btrtl_dev->fw_len - 7, /* Cut the tail */
  	};
 
-	rc = btrtl_vendor_read_reg16(hdev, RTL_SEC_PROJ, reg_val);
-	if (rc < 0)
-		return -EIO;
-	key_id = reg_val[0];
-
-	rtl_dev_dbg(hdev, "%s: key id %u", __func__, key_id);
-
-	btrtl_dev->key_id = key_id;
+	key_id = btrtl_dev->key_id;
 
  	hdr = rtl_iov_pull_data(&iov, sizeof(*hdr));
  	if (!hdr)
@@ -1081,6 +1073,8 @@ struct btrtl_device_info *btrtl_initialize(struct hci_dev *hdev,
  	u16 hci_rev, lmp_subver;
  	u8 hci_ver, lmp_ver, chip_type = 0;
  	int ret;
+	int rc;
+	u8 key_id;
  	u8 reg_val[2];
 
  	btrtl_dev = kzalloc(sizeof(*btrtl_dev), GFP_KERNEL);
@@ -1191,6 +1185,14 @@ struct btrtl_device_info *btrtl_initialize(struct hci_dev *hdev,
  		goto err_free;
  	}
 
+	rc = btrtl_vendor_read_reg16(hdev, RTL_SEC_PROJ, reg_val);
+	if (rc < 0)
+		goto err_free;
+
+	key_id = reg_val[0];
+	btrtl_dev->key_id = key_id;
+	rtl_dev_info(hdev, "%s: key id %u", __func__, key_id);
+
  	btrtl_dev->fw_len = -EIO;
  	if (lmp_subver == RTL_ROM_LMP_8852A && hci_rev == 0x000c) {
  		snprintf(fw_name, sizeof(fw_name), "%s_v2.bin",

drivers/bluetooth/btrtl.c struct btrtl_device_info *btrtl_initialize(struct hci_dev *hdev, · line 1221

Quoted 8 lines
drivers/bluetooth/btrtl.c +1 -1
@@ -1213,7 +1215,7 @@ struct btrtl_device_info *btrtl_initialize(struct hci_dev *hdev,
  		goto err_free;
  	}
 
-	if (btrtl_dev->ic_info->cfg_name) {
+	if (btrtl_dev->ic_info->cfg_name && !btrtl_dev->key_id) {
  		if (postfix) {
  			snprintf(cfg_name, sizeof(cfg_name), "%s-%s.bin",
  				 btrtl_dev->ic_info->cfg_name, postfix);

Kind regards,

Paul