Skip to contentSkip to conversation

dt-bindings: display: bridge: ldb: Document nxp, termination-resistor

PATCH Superseded Fabio Estevam 2 participants 3 messages Nov 18, 2025

Subsystems (5)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Fabio Estevam

author reviewer
#0 lore raw

PATCH 1/2 dt-bindings: display: bridge: ldb: Document nxp, termination-resistor

Document the optional nxp,termination-resistor property for the i.MX LVDS display bridge.

This boolean property indicates that the built-in 100 Ohm termination resistor on the LVDS output is enabled. It is controlled via the HS_EN bit in the LVDS_CTRL register. Enabling the resistor can improve LVDS signal quality and may prevent visual artifacts on some boards, but increases the power consumption.

---
 .../devicetree/bindings/display/bridge/fsl,ldb.yaml      | 9 +++++++++
 1 file changed, 9 insertions(+)
Documentation/devicetree/bindings/display/bridge/fsl,ldb.yaml +9 -0
index 07388bf2b90d..6bc786204e65 100644
@@ -35,6 +35,15 @@ properties:
       - const: ldb
       - const: lvds
 
+  nxp,termination-resistor:
+    type: boolean
+    description:
+      Indicates that the built-in 100 Ohm termination resistor on the LVDS
+      output is enabled. This property is optional and controlled via the
+      HS_EN bit in the LVDS_CTRL register. Enabling it can improve signal
+      quality and prevent visual artifacts on some boards, but increases
+      power consumption.
+
   ports:
     $ref: /schemas/graph.yaml#/properties/ports
 
Signature · 1 line
2.34.1
author reviewer
#1 lore raw

PATCH 2/2 drm/bridge: fsl-ldb: Allow the termination resistor to be enabled

The LVDS Control Register (LVDS_CTRL) register has an HS_EN bit that allows the 100 Ohm termination resistor in the chip to be enabled.

Add support to setting the HS_EN bit when the "nxp,termination-resistor" optional property is present.

The motivation for introducing this property was a custom i.MX8MP board that was showing visual artifacts. After enabling the 100 Ohm termination resistor the LVDS signal quality improved causing the artifacts to disappear.

---
 drivers/gpu/drm/bridge/fsl-ldb.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/gpu/drm/bridge/fsl-ldb.c +9 -0
index 5c3cf37200bc..b4b9130de32c 100644
@@ -92,6 +92,7 @@ struct fsl_ldb {
 	const struct fsl_ldb_devdata *devdata;
 	bool ch0_enabled;
 	bool ch1_enabled;
+	bool termination_resistor;
 };
 
 static bool fsl_ldb_is_dual(const struct fsl_ldb *fsl_ldb)
@@ -212,6 +213,10 @@ static void fsl_ldb_atomic_enable(struct drm_bridge *bridge,
 	/* Program LVDS_CTRL */
 	reg = LVDS_CTRL_CC_ADJ(2) | LVDS_CTRL_PRE_EMPH_EN |
 	      LVDS_CTRL_PRE_EMPH_ADJ(3) | LVDS_CTRL_VBG_EN;
+
+	reg &= ~LVDS_CTRL_HS_EN;
+	if (fsl_ldb->termination_resistor)
+		reg |= LVDS_CTRL_HS_EN;
 	regmap_write(fsl_ldb->regmap, fsl_ldb->devdata->lvds_ctrl, reg);
 
 	/* Wait for VBG to stabilize. */
@@ -292,6 +297,7 @@ static const struct drm_bridge_funcs funcs = {
 static int fsl_ldb_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
 	struct device_node *panel_node;
 	struct device_node *remote1, *remote2;
 	struct drm_panel *panel;
@@ -340,6 +346,9 @@ static int fsl_ldb_probe(struct platform_device *pdev)
 	if (IS_ERR(panel))
 		return PTR_ERR(panel);
 
+	if (of_property_present(np, "nxp,termination-resistor"))
+		fsl_ldb->termination_resistor = true;
+
 	fsl_ldb->panel_bridge = devm_drm_panel_bridge_add(dev, panel);
 	if (IS_ERR(fsl_ldb->panel_bridge))
 		return PTR_ERR(fsl_ldb->panel_bridge);
Signature · 1 line
2.34.1
maintainer
#2 lore raw

Re: [PATCH 1/2] dt-bindings: display: bridge: ldb: Document nxp,termination-resistor

In reply to Fabio Estevam
Quoted 19 lines · Fabio Estevam

Document the optional nxp,termination-resistor property for the i.MX LVDS display bridge.

This boolean property indicates that the built-in 100 Ohm termination resistor on the LVDS output is enabled. It is controlled via the HS_EN bit in the LVDS_CTRL register. Enabling the resistor can improve LVDS signal quality and may prevent visual artifacts on some boards, but increases the power consumption.

---
 .../devicetree/bindings/display/bridge/fsl,ldb.yaml      | 9 +++++++++
 1 file changed, 9 insertions(+)
Documentation/devicetree/bindings/display/bridge/fsl,ldb.yaml +0 -0
index 07388bf2b90d..6bc786204e65 100644

Documentation/devicetree/bindings/display/bridge/fsl,ldb.yaml properties: · line 38

Quoted 4 lines
Documentation/devicetree/bindings/display/bridge/fsl,ldb.yaml +1 -0
@@ -35,6 +35,15 @@ properties:
       - const: ldb
       - const: lvds
 
+  nxp,termination-resistor:

the name looks like resistor value, how about nxp,term-resistor-en?

Frank

Quoted 14 lines
Documentation/devicetree/bindings/display/bridge/fsl,ldb.yaml +8 -1
+    type: boolean
+    description:
+      Indicates that the built-in 100 Ohm termination resistor on the LVDS
+      output is enabled. This property is optional and controlled via the
+      HS_EN bit in the LVDS_CTRL register. Enabling it can improve signal
+      quality and prevent visual artifacts on some boards, but increases
+      power consumption.
+
   ports:
     $ref: /schemas/graph.yaml#/properties/ports
 
--

2.34.1