Skip to contentSkip to conversation

Add driver support for Eswin EIC7700 SoC PCIe controller

PATCH Superseded [email protected] 4 participants 15 messages Dec 2, 2025 – Dec 15, 2025

Subsystems (4)

v7 of 11 Superseded Latest is v11 →

lore
Share & tools
lore
#0 lore raw

v7 cover Add driver support for Eswin EIC7700 SoC PCIe controller

From: Senchuan Zhang <[email protected]>

Changes in v7:
- Updates: eswin,eic7700-pcie.yaml
- None

- Updates: pcie-eic7700.c
- Update "config PCIE_EIC7700" bool to tristate.
- Remove fix MSI-X code, depend on new commit [1].
- Add set no_pme_handshake flag.
- Update -EINVAL to -ENODATA and add PM runtime function.
- Add ".probe_type = PROBE_PREFER_ASYNCHRONOUS,".
- Update eic7700_pcie_perst_deassert function name to

    eic7700_pcie_perst_reset.

- Update readw to dw_pcie_readw_dbi function.
- Add comments above reset_control_bulk_deassert function.

- Updates: pcie-designware.h pcie-designware-host.c
- The ESWIN EIC7700 SoC lacks hardware support for the L2/L3 low-power
link states. It cannot enter the L2/L3 ready state through the PME_Turn_Off/PME_To_Ack handshake protocol. To address this, add a
no_pme_handshake flag skip PME_Turn_Off broadcast and link state check
code, other driver can reuse this flag if meet the similar situation.
- Link to V6: https://lore.kernel.org/linux-pci/[email protected]/
- Link to: https://lore.kernel.org/linux-pci/[email protected]/ [1]

Changes in v6:
- Updates: eswin,eic7700-pcie.yaml
- Add Reviewed-by: Rob Herring (Arm) <[email protected]>.

- Updates: pcie-eic7700.c
- Remove pci_root_ports_have_device function judgment during suspend.
- Remove eic7700_pcie_pme_turn_off and eic7700_pcie_get_ltssm function.
- Add set no_suspport_L2 flag.

- Updates: pcie-designware.h pcie-designware-host.c
- The ESWIN EIC7700 soc does not support enter L2 link state. Therefore
add no_suspport_L2 flag skip PME_Turn_Off broadcast and link state
check code, other driver can reuse this flag if meet the similar
situation.
- Link to V5: https://lore.kernel.org/all/[email protected]/
- Link to: https://lore.kernel.org/all/e7plmtwtkkd4ymrt2hkztcqdx4ugfjk64oksjyf6lpi2oui53d@vhuo5occyref/

Changes in v5:
- Updates: eswin,eic7700-pcie.yaml
- Modify reg-names: update mgmt to elbi.
- Modify clock-names: update pclk to phy_reg.
- Modify reset-names: update powerup to pwr.
- Remove powerup modify in "snps,dw-pcie-common.yaml" file.

- Updates: pcie-eic7700.c
- Update the driver submission comment, mention EIC7700 in the "config PCIE_EIC7700" and in the driver title.
- Update some comments, for examples: "s/PME_TURN_OFF/PME_Turn_Off/",

    "s/INTX/INTx/", "s/PERST/PERST#/", "s/perst/PERST#/", "s/id/ID/".

- Update "struct *_pcie" name and function name, add the eic7700 prefix.
- Use PCIEELBI_CTRL0_DEV_TYPE macro and update comment, use FIELD_PREP.
- Add eic7700_pcie_data pointer in struct eic7700_pcie.
- Update .deinit callback function name and removed the dw_pcie_link_up judgment, add pci_root_ports_have_device function judgment.
- Remove devm_platform_ioremap_resource_byname function get mgmt, use platform_get_resource_byname function get elbi in "pcie-designware.c".
- Update of_reset_control_get to of_reset_control_get_exclusive, use devm_reset_control_bulk_get_exclusive function get resets, update use reset_control_bulk_assert/reset_control_bulk_deassert function.
- Link to V4: https://lore.kernel.org/all/[email protected]/
- Link to https://git.kernel.org/pub/scm/linux/kernel/git/pci/pci.git/tree/?h=controller/dwc

Changes in v4:
- Updates: eswin,eic7700-pcie.yaml
- Use snps,dw-pcie.yaml instead pci-host-bridge.yaml.

- Updates: snps,dw-pcie-common.yaml
- Add powerup reset property, our powerup property is somewhat different from the general attributes defined by Synopsys DWC binding.

- Updates: pcie-eic7700.c
- Update the driver submission comment.
- Alphabetize so the menuconfig entries remain sorted by vendor.
- Update use PCI_CAP_LIST_NEXT_MASK macro.
- Use readl_poll_timeout function.
- Update eswin_pcie_suspend/eswin_pcie_resume name to eswin_pcie_suspend_noirq/eswin_pcie_resume_noirq.
- PM use dw_pcie_suspend_noirq and dw_pcie_resume_noirq function and add eswin_pcie_get_ltssm, eswin_pcie_pme_turn_off, eswin_pcie_host_exit
function adapt to PM.
- Link to V3: https://lore.kernel.org/linux-pci/[email protected]/

Changes in v3:
- Updates: eswin,eic7700-pcie.yaml
- Based on the last patch yaml file, devicetree separates the root port node, changing it significantly. Therefore, "Reviewed-by: Krzysztof Kozlowski <[email protected]>" is not added.
- Clock and reset drivers are under review. In yaml, macro definitions used in clock and reset can only be replaced by constant values.
- Move the num-lanes and perst resets to the PCIe Root Port node, make it easier to support multiple Root Ports in future versions of the hardware.
- Update the num-lanes attribute and modify define num-lanes as decimal.
- Optimize the ranges attribute and clear the relocatable flag (bit 31) for any regions.
- Update comment: inte~inth are actual interrupts and these names align with the interrupt names in the hardware IP, inte~inth interrupts corresponds to Deassert_INTA~Deassert_INTD.
- Add Signed-off-by: Yanghui Ou <[email protected]>.

- Updates: pcie-eic7700.c
- Update the submission comment and add DWC IP revision, data rate, lane information.
- Optimize the "config PCIE_EIC7700" configuration.
- Optimize the macro definition, add bitfield definition for the mask,
and remove redundant comments. optimize comments, make use of 80
columns for comments.
- Use the dw_pcie_find_capability function to obtain the offset by
traversing the function list.
- Remove the sets MPS code and configure it by PCI core.
- Alphabetize so the menuconfig entries remain sorted by vendor.
- Configure ESWIN VID:DID for Root Port as the default values are
invalid,and remove the redundant lane config.
- Use reverse Xmas order for all local variables in this driver
- Hardware doesn't support MSI-X but it advertises MSI-X capability, set
a flag and clear it conditionally.
- Resets are all necessary, Update the interface function for resets.
- Since driver does not depend on any parent to power on any resource,
the pm runtime related functions are removed.
- Remove "eswin_pcie_shutdown" function, our comment on the shutdown
function is incorrect. Moreover, when the host powers reboots,it will
enter the shutdown function, we are using host reset and do not need
to assert perst. Therefore, the shutdown function is not necessary.
- remove "eswin_pcie_remove", because it is not safe to remove it during
runtime, and this driver has been modified to builtin_platform_driver
and does not support hot plugging, therefore, the remove function is
not needed.
- The Suspend function adds link state judgment, and for controllers
with active devices, resources cannot be turned off.
- Add Signed-off-by: Yanghui Ou <[email protected]>.
- Link to V2: https://lore.kernel.org/linux-pci/[email protected]/

Changes in v2:
- Updates: eswin,eic7700-pcie.yaml
- Optimize the naming of "clock-names" and "reset-names".
- Add a reference to "$ref: /schemas/pci/pci-host-bridge.yaml#". (The name of the reset attribute in the "snps,dw-pcie-common.yaml" file is different from our reset attribute and "snps,dw-pcie.yaml" file cannot be directly referenced)
- Follow DTS coding style to optimize yaml attributes.
- Remove status = "disabled" from yaml.

- Updates: pcie-eic7700.c
- Remove unnecessary imported header files.
- Use dev_err instead of pr_err and remove the WARN_ON function.
- The eswin_evb_socket_power_on function is removed and not supported.
- The eswin_pcie_remove function is placed after the probe function.
- Optimize function alignment.
- Manage the clock using the devm_clk_bulk_get_all_enabled function.
- Handle the release of resources after the dw_pcie_host_init function
call fails.
- Remove the dev_dbg function and remove __exit_p.
- Add support for the system pm function.
- Link to V1: https://lore.kernel.org/all/[email protected]/

Senchuan Zhang (3):
dt-bindings: PCI: eic7700: Add Eswin PCIe host controller
PCI: eic7700: Add Eswin PCIe host controller driver
PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast

 .../bindings/pci/eswin,eic7700-pcie.yaml      | 167 ++++++++
 drivers/pci/controller/dwc/Kconfig            |  11 +
 drivers/pci/controller/dwc/Makefile           |   1 +
 .../pci/controller/dwc/pcie-designware-host.c |   4 +
 drivers/pci/controller/dwc/pcie-designware.h  |   1 +
 drivers/pci/controller/dwc/pcie-eic7700.c     | 378 ++++++++++++++++++
 6 files changed, 562 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/eswin,eic7700-pcie.yaml
 create mode 100644 drivers/pci/controller/dwc/pcie-eic7700.c

--
2.25.1

#1 lore raw

PATCH v7 1/3 dt-bindings: PCI: eic7700: Add Eswin PCIe host controller

From: Senchuan Zhang <[email protected]>

Add Device Tree binding documentation for the Eswin EIC7700 PCIe controller module, the PCIe controller enables the core to correctly initialize and manage the PCIe bus and connected devices.

---
 .../bindings/pci/eswin,eic7700-pcie.yaml      | 167 ++++++++++++++++++
 1 file changed, 167 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/eswin,eic7700-pcie.yaml
Documentation/devicetree/bindings/pci/eswin,eic7700-pcie.yaml new file +167 -0
new file mode 100644
index 000000000000..9c0150834e6d
@@ -0,0 +1,167 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/eswin,eic7700-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Eswin EIC7700 PCIe host controller
+
+maintainers:
+  - Yu Ning <[email protected]>
+  - Senchuan Zhang <[email protected]>
+  - Yanghui Ou <[email protected]>
+
+description:
+  Eswin EIC7700 SoC PCIe root complex controller is based on the Synopsys
+  DesignWare PCIe IP.
+
+properties:
+  compatible:
+    const: eswin,eic7700-pcie
+
+  reg:
+    maxItems: 3
+
+  reg-names:
+    items:
+      - const: dbi
+      - const: config
+      - const: elbi
+
+  ranges:
+    maxItems: 3
+
+  '#interrupt-cells':
+    const: 1
+
+  interrupt-names:
+    items:
+      - const: msi
+      - const: inta
+      - const: intb
+      - const: intc
+      - const: intd
+
+  interrupt-map:
+    maxItems: 4
+
+  interrupt-map-mask:
+    items:
+      - const: 0
+      - const: 0
+      - const: 0
+      - const: 7
+
+  clocks:
+    maxItems: 4
+
+  clock-names:
+    items:
+      - const: mstr
+      - const: dbi
+      - const: phy_reg
+      - const: aux
+
+  resets:
+    maxItems: 2
+
+  reset-names:
+    items:
+      - const: dbi
+      - const: pwr
+
+patternProperties:
+  "^pcie@":
+    type: object
+    $ref: /schemas/pci/pci-pci-bridge.yaml#
+
+    properties:
+      reg:
+        maxItems: 1
+
+      num-lanes:
+        maximum: 4
+
+      resets:
+        maxItems: 1
+
+      reset-names:
+        items:
+          - const: perst
+
+    required:
+      - reg
+      - ranges
+      - num-lanes
+      - resets
+      - reset-names
+
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - ranges
+  - interrupts
+  - interrupt-names
+  - interrupt-map-mask
+  - interrupt-map
+  - '#interrupt-cells'
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+
+allOf:
+  - $ref: /schemas/pci/snps,dw-pcie.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        pcie@54000000 {
+            compatible = "eswin,eic7700-pcie";
+            reg = <0x0 0x54000000 0x0 0x4000000>,
+                  <0x0 0x40000000 0x0 0x800000>,
+                  <0x0 0x50000000 0x0 0x100000>;
+            reg-names = "dbi", "config", "elbi";
+            #address-cells = <3>;
+            #size-cells = <2>;
+            #interrupt-cells = <1>;
+            ranges = <0x01000000 0x0 0x40800000 0x0 0x40800000 0x0 0x800000>,
+                     <0x02000000 0x0 0x41000000 0x0 0x41000000 0x0 0xf000000>,
+                     <0x43000000 0x80 0x00000000 0x80 0x00000000 0x2 0x00000000>;
+            bus-range = <0x00 0xff>;
+            clocks = <&clock 144>,
+                     <&clock 145>,
+                     <&clock 146>,
+                     <&clock 147>;
+            clock-names = "mstr", "dbi", "phy_reg", "aux";
+            resets = <&reset 97>,
+                     <&reset 98>;
+            reset-names = "dbi", "pwr";
+            interrupts = <220>, <179>, <180>, <181>, <182>, <183>, <184>, <185>, <186>;
+            interrupt-names = "msi", "inta", "intb", "intc", "intd";
+            interrupt-parent = <&plic>;
+            interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+            interrupt-map = <0x0 0x0 0x0 0x1 &plic 179>,
+                            <0x0 0x0 0x0 0x2 &plic 180>,
+                            <0x0 0x0 0x0 0x3 &plic 181>,
+                            <0x0 0x0 0x0 0x4 &plic 182>;
+            device_type = "pci";
+            pcie@0 {
+                reg = <0x0 0x0 0x0 0x0 0x0>;
+                #address-cells = <3>;
+                #size-cells = <2>;
+                ranges;
+                device_type = "pci";
+                num-lanes = <4>;
+                resets = <&reset 99>;
+                reset-names = "perst";
+            };
+        };
+    };
Signature · 1 line
2.25.1
#2 lore raw

PATCH v7 2/3 PCI: eic7700: Add Eswin PCIe host controller driver

In reply to [email protected]

From: Senchuan Zhang <[email protected]>

Add driver for the Eswin EIC7700 PCIe host controller, which is based on the DesignWare PCIe core, IP revision 5.96a. The PCIe Gen.3 controller supports a data rate of 8 GT/s and 4 channels, support INTx and MSI interrupts.

---
 drivers/pci/controller/dwc/Kconfig        |  11 +
 drivers/pci/controller/dwc/Makefile       |   1 +
 drivers/pci/controller/dwc/pcie-eic7700.c | 378 ++++++++++++++++++++++
 3 files changed, 390 insertions(+)
 create mode 100644 drivers/pci/controller/dwc/pcie-eic7700.c
drivers/pci/controller/dwc/Kconfig +11 -0
index 519b59422b47..c837cb5947b6 100644
@@ -93,6 +93,17 @@ config PCIE_BT1
 	  Enables support for the PCIe controller in the Baikal-T1 SoC to work
 	  in host mode. It's based on the Synopsys DWC PCIe v4.60a IP-core.
 
+config PCIE_EIC7700
+	tristate "Eswin EIC7700 PCIe controller"
+	depends on ARCH_ESWIN || COMPILE_TEST
+	depends on PCI_MSI
+	select PCIE_DW_HOST
+	help
+	  Say Y here if you want PCIe controller support for the Eswin EIC7700.
+	  The PCIe controller on EIC7700 is based on DesignWare hardware,
+	  enables support for the PCIe controller in the EIC7700 SoC to work in
+	  host mode.
+
 config PCI_IMX6
 	bool
 
drivers/pci/controller/dwc/Makefile +1 -0
index 67ba59c02038..7c5a5186ea83 100644
@@ -6,6 +6,7 @@ obj-$(CONFIG_PCIE_DW_EP) += pcie-designware-ep.o
 obj-$(CONFIG_PCIE_DW_PLAT) += pcie-designware-plat.o
 obj-$(CONFIG_PCIE_AMD_MDB) += pcie-amd-mdb.o
 obj-$(CONFIG_PCIE_BT1) += pcie-bt1.o
+obj-$(CONFIG_PCIE_EIC7700) += pcie-eic7700.o
 obj-$(CONFIG_PCI_DRA7XX) += pci-dra7xx.o
 obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
 obj-$(CONFIG_PCIE_FU740) += pcie-fu740.o
drivers/pci/controller/dwc/pcie-eic7700.c new file +378 -0

378 lines not on this page · raw message

Signature · 1 line
2.25.1
#3 lore raw

Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 278 lines · On 12/2/2025 2:34 PM, [email protected] wrote:

From: Senchuan Zhang <[email protected]>

Add driver for the Eswin EIC7700 PCIe host controller, which is based on the DesignWare PCIe core, IP revision 5.96a. The PCIe Gen.3 controller supports a data rate of 8 GT/s and 4 channels, support INTx and MSI interrupts.

---
  drivers/pci/controller/dwc/Kconfig        |  11 +
  drivers/pci/controller/dwc/Makefile       |   1 +
  drivers/pci/controller/dwc/pcie-eic7700.c | 378 ++++++++++++++++++++++
  3 files changed, 390 insertions(+)

create mode 100644 drivers/pci/controller/dwc/pcie-eic7700.c

drivers/pci/controller/dwc/Kconfig +11 -0
index 519b59422b47..c837cb5947b6 100644
@@ -93,6 +93,17 @@ config PCIE_BT1
  	  Enables support for the PCIe controller in the Baikal-T1 SoC to work
  	  in host mode. It's based on the Synopsys DWC PCIe v4.60a IP-core.
 
+config PCIE_EIC7700
+	tristate "Eswin EIC7700 PCIe controller"
+	depends on ARCH_ESWIN || COMPILE_TEST
+	depends on PCI_MSI
+	select PCIE_DW_HOST
+	help
+	  Say Y here if you want PCIe controller support for the Eswin EIC7700.
+	  The PCIe controller on EIC7700 is based on DesignWare hardware,
+	  enables support for the PCIe controller in the EIC7700 SoC to work in
+	  host mode.
+
  config PCI_IMX6
  	bool
 
drivers/pci/controller/dwc/Makefile +1 -0
index 67ba59c02038..7c5a5186ea83 100644
@@ -6,6 +6,7 @@ obj-$(CONFIG_PCIE_DW_EP) += pcie-designware-ep.o
  obj-$(CONFIG_PCIE_DW_PLAT) += pcie-designware-plat.o
  obj-$(CONFIG_PCIE_AMD_MDB) += pcie-amd-mdb.o
  obj-$(CONFIG_PCIE_BT1) += pcie-bt1.o
+obj-$(CONFIG_PCIE_EIC7700) += pcie-eic7700.o
  obj-$(CONFIG_PCI_DRA7XX) += pci-dra7xx.o
  obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
  obj-$(CONFIG_PCIE_FU740) += pcie-fu740.o
drivers/pci/controller/dwc/pcie-eic7700.c new file +221 -0
new file mode 100644
index 000000000000..cb7cdea6a94b
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ESWIN EIC7700 PCIe root complex driver
+ *
+ * Copyright 2025, Beijing ESWIN Computing Technology Co., Ltd.
+ *
+ * Authors: Yu Ning <[email protected]>
+ *          Senchuan Zhang <[email protected]>
+ *          Yanghui Ou <[email protected]>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/resource.h>
+#include <linux/reset.h>
+#include <linux/types.h>
+
+#include "pcie-designware.h"
+
+/* ELBI registers */
+#define PCIEELBI_CTRL0_OFFSET		0x0
+#define PCIEELBI_STATUS0_OFFSET		0x100
+
+/* LTSSM register fields */
+#define PCIEELBI_APP_LTSSM_ENABLE	BIT(5)
+
+/* APP_HOLD_PHY_RST register fields */
+#define PCIEELBI_APP_HOLD_PHY_RST	BIT(6)
+
+/* PM_SEL_AUX_CLK register fields */
+#define PCIEELBI_PM_SEL_AUX_CLK		BIT(16)
+
+/* DEV_TYPE register fields */
+#define PCIEELBI_CTRL0_DEV_TYPE		GENMASK(3, 0)
+
+/* Vendor and device ID value */
+#define PCI_VENDOR_ID_ESWIN		0x1fe1
+#define PCI_DEVICE_ID_ESWIN		0x2030
+
+#define EIC7700_NUM_RSTS		ARRAY_SIZE(eic7700_pcie_rsts)
+
+static const char * const eic7700_pcie_rsts[] = {
+	"pwr",
+	"dbi",
+};
+
+struct eic7700_pcie_data {
+	bool no_pme_handshake;
+};
+
+struct eic7700_pcie_port {
+	struct list_head list;
+	struct reset_control *perst;
+	int num_lanes;
+};
+
+struct eic7700_pcie {
+	struct dw_pcie pci;
+	struct clk_bulk_data *clks;
+	struct reset_control_bulk_data resets[EIC7700_NUM_RSTS];
+	struct list_head ports;
+	const struct eic7700_pcie_data *data;
+	int num_clks;
+};
+
+#define to_eic7700_pcie(x) dev_get_drvdata((x)->dev)
+
+static int eic7700_pcie_start_link(struct dw_pcie *pci)
+{
+	u32 val;
+
+	/* Enable LTSSM */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val |= PCIEELBI_APP_LTSSM_ENABLE;
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	return 0;
+}
+
+static bool eic7700_pcie_link_up(struct dw_pcie *pci)
+{
+	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	u16 val = dw_pcie_readw_dbi(pci, offset + PCI_EXP_LNKSTA);
+
+	return val & PCI_EXP_LNKSTA_DLLLA;
+}
+
+static int eic7700_pcie_perst_reset(struct eic7700_pcie_port *port,
+				    struct eic7700_pcie *pcie)
+{
+	int ret;
+
+	ret = reset_control_assert(port->perst);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to assert PERST#\n");
+		return ret;
+	}
+
+	/* Ensure that PERST# has been asserted for at least 100 ms */
+	msleep(PCIE_T_PVPERL_MS);
+
+	ret = reset_control_deassert(port->perst);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to deassert PERST#\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int eic7700_pcie_parse_port(struct eic7700_pcie *pcie,
+				   struct device_node *node)
+{
+	struct device *dev = pcie->pci.dev;
+	struct eic7700_pcie_port *port;
+
+	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	port->perst = of_reset_control_get_exclusive(node, "perst");
+	if (IS_ERR(port->perst)) {
+		dev_err(dev, "Failed to get PERST# reset\n");
+		return PTR_ERR(port->perst);
+	}
+
+	/*
+	 * TODO: Since the Root Port node is separated out by pcie devicetree,
+	 * the DWC core initialization code can't parse the num-lanes attribute
+	 * in the Root Port. Before entering the DWC core initialization code,
+	 * the platform driver code parses the Root Port node. The EIC7700 only
+	 * supports one Root Port node, and the num-lanes attribute is suitable
+	 * for the case of one Root Rort.
+	 */
+	if (!of_property_read_u32(node, "num-lanes", &port->num_lanes))
+		pcie->pci.num_lanes = port->num_lanes;
+
+	INIT_LIST_HEAD(&port->list);
+	list_add_tail(&port->list, &pcie->ports);
+
+	return 0;
+}
+
+static int eic7700_pcie_parse_ports(struct eic7700_pcie *pcie)
+{
+	struct eic7700_pcie_port *port, *tmp;
+	struct device *dev = pcie->pci.dev;
+	int ret;
+
+	for_each_available_child_of_node_scoped(dev->of_node, of_port) {
+		ret = eic7700_pcie_parse_port(pcie, of_port);
+		if (ret)
+			goto err_port;
+	}
+
+	return 0;
+
+err_port:
+	list_for_each_entry_safe(port, tmp, &pcie->ports, list)
+		list_del(&port->list);
+
+	return ret;
+}
+
+static int eic7700_pcie_host_init(struct dw_pcie_rp *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct eic7700_pcie *pcie = to_eic7700_pcie(pci);
+	struct eic7700_pcie_port *port;
+	u32 val;
+	int ret;
+
+	pcie->num_clks = devm_clk_bulk_get_all_enabled(pci->dev, &pcie->clks);
+	if (pcie->num_clks < 0)
+		return dev_err_probe(pci->dev, pcie->num_clks,
+				     "Failed to get pcie clocks\n");
+
+	/*
+	 * The PWR and DBI Reset signals are respectively used to reset the
+	 * PCIe controller and the DBI registers.
+	 * The PERST# signal is a reset signal that simultaneously controls the
+	 * PCIe controller, PHY, and Endpoint.
+	 * Before configuring the PHY, the PERST# signal must first be
+	 * deasserted.
+	 * The external reference clock is supplied simultaneously to the PHY
+	 * and EP. When the PHY is configurable, the entire chip already has
+	 * stable power and reference clock.
+	 * The PHY will be ready within 20ms after writing app_hold_phy_rst
+	 * register of ELBI register space.
+	 */
+	ret = reset_control_bulk_deassert(EIC7700_NUM_RSTS, pcie->resets);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to deassert resets\n");
+		return ret;
+	}
+
+	/* Configure Root Port type */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val &= ~PCIEELBI_CTRL0_DEV_TYPE;
+	val |= FIELD_PREP(PCIEELBI_CTRL0_DEV_TYPE, PCI_EXP_TYPE_ROOT_PORT);
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	list_for_each_entry(port, &pcie->ports, list) {
+		ret = eic7700_pcie_perst_reset(port, pcie);
+		if (ret)
+			goto err_perst;
+	}
+
+	/* Configure app_hold_phy_rst */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val &= ~PCIEELBI_APP_HOLD_PHY_RST;
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	/* The maximum waiting time for the clock switch lock is 20ms */
+	ret = readl_poll_timeout(pci->elbi_base + PCIEELBI_STATUS0_OFFSET,
+				 val, !(val & PCIEELBI_PM_SEL_AUX_CLK), 1000,

drivers/pci/controller/dwc/pcie-eic7700.c line 231

Quoted 10 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +10 -0
+				 20000);
+	if (ret) {
+		dev_err(pci->dev, "Timeout waiting for PM_SEL_AUX_CLK ready\n");
+		goto err_phy_init;
+	}
+
+	/*
+	 * Configure ESWIN VID:DID for Root Port as the default values are
+	 * invalid.
+	 */

we need to make dbi registers writeable before this through this API dw_pcie_dbi_ro_wr_en().

Quoted 72 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +72 -0
+	dw_pcie_writew_dbi(pci, PCI_VENDOR_ID, PCI_VENDOR_ID_ESWIN);
+	dw_pcie_writew_dbi(pci, PCI_DEVICE_ID, PCI_DEVICE_ID_ESWIN);
+
+	return 0;
+
+err_phy_init:
+	list_for_each_entry(port, &pcie->ports, list)
+		reset_control_assert(port->perst);
+err_perst:
+	reset_control_bulk_assert(EIC7700_NUM_RSTS, pcie->resets);
+
+	return ret;
+}
+
+static void eic7700_pcie_host_deinit(struct dw_pcie_rp *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct eic7700_pcie *pcie = to_eic7700_pcie(pci);
+	struct eic7700_pcie_port *port;
+
+	list_for_each_entry(port, &pcie->ports, list)
+		reset_control_assert(port->perst);
+	reset_control_bulk_assert(EIC7700_NUM_RSTS, pcie->resets);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
+}
+
+static const struct dw_pcie_host_ops eic7700_pcie_host_ops = {
+	.init = eic7700_pcie_host_init,
+	.deinit = eic7700_pcie_host_deinit,
+};
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+	.start_link = eic7700_pcie_start_link,
+	.link_up = eic7700_pcie_link_up,
+};
+
+static int eic7700_pcie_probe(struct platform_device *pdev)
+{
+	const struct eic7700_pcie_data *data;
+	struct eic7700_pcie_port *port, *tmp;
+	struct device *dev = &pdev->dev;
+	struct eic7700_pcie *pcie;
+	struct dw_pcie *pci;
+	int ret, i;
+
+	data = of_device_get_match_data(dev);
+	if (!data)
+		return dev_err_probe(dev, -ENODATA, "OF data missing\n");
+
+	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
+	if (!pcie)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&pcie->ports);
+
+	pci = &pcie->pci;
+	pci->dev = dev;
+	pci->ops = &dw_pcie_ops;
+	pci->pp.ops = &eic7700_pcie_host_ops;
+	pcie->data = data;
+	pci->no_pme_handshake = pcie->data->no_pme_handshake;
+
+	for (i = 0; i < EIC7700_NUM_RSTS; i++)
+		pcie->resets[i].id = eic7700_pcie_rsts[i];
+
+	ret = devm_reset_control_bulk_get_exclusive(dev, EIC7700_NUM_RSTS,
+						    pcie->resets);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to get resets\n");
+
+	ret = eic7700_pcie_parse_ports(pcie);
+	if (ret)

drivers/pci/controller/dwc/pcie-eic7700.c line 313

Quoted 10 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +10 -0
+		return dev_err_probe(dev, ret,
+				     "Failed to parse Root Port: %d\n", ret);
+
+	platform_set_drvdata(pdev, pcie);
+
+	pm_runtime_no_callbacks(dev);
+	devm_pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0)
+		goto err_pm_runtime_put;

Any specific reason why we are enabling runtime pm and doing pm_runtime_get_sync()

- Krishna Chaitanya.

Quoted 65 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +65 -0
+
+	ret = dw_pcie_host_init(&pci->pp);
+	if (ret) {
+		dev_err(dev, "Failed to initialize host\n");
+		goto err_init;
+	}
+
+	return 0;
+
+err_init:
+	list_for_each_entry_safe(port, tmp, &pcie->ports, list) {
+		list_del(&port->list);
+		reset_control_put(port->perst);
+	}
+err_pm_runtime_put:
+	pm_runtime_put(dev);
+
+	return ret;
+}
+
+static int eic7700_pcie_suspend_noirq(struct device *dev)
+{
+	struct eic7700_pcie *pcie = dev_get_drvdata(dev);
+
+	return dw_pcie_suspend_noirq(&pcie->pci);
+}
+
+static int eic7700_pcie_resume_noirq(struct device *dev)
+{
+	struct eic7700_pcie *pcie = dev_get_drvdata(dev);
+
+	return dw_pcie_resume_noirq(&pcie->pci);
+}
+
+static const struct dev_pm_ops eic7700_pcie_pm_ops = {
+	NOIRQ_SYSTEM_SLEEP_PM_OPS(eic7700_pcie_suspend_noirq,
+				  eic7700_pcie_resume_noirq)
+};
+
+static const struct eic7700_pcie_data eic7700_data = {
+	.no_pme_handshake = true,
+};
+
+static const struct of_device_id eic7700_pcie_of_match[] = {
+	{ .compatible = "eswin,eic7700-pcie", .data = &eic7700_data },
+	{},
+};
+
+static struct platform_driver eic7700_pcie_driver = {
+	.probe = eic7700_pcie_probe,
+	.driver = {
+		.name = "eic7700-pcie",
+		.of_match_table = eic7700_pcie_of_match,
+		.suppress_bind_attrs = true,
+		.pm = &eic7700_pcie_pm_ops,
+		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
+	},
+};
+builtin_platform_driver(eic7700_pcie_driver);
+
+MODULE_DESCRIPTION("Eswin EIC7700 PCIe host controller driver");
+MODULE_AUTHOR("Yu Ning <[email protected]>");
+MODULE_AUTHOR("Senchuan Zhang <[email protected]>");
+MODULE_AUTHOR("Yanghui Ou <[email protected]>");
+MODULE_LICENSE("GPL");
#4 lore raw

Re: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 295 lines

-----Original Messages-----
From: "Krishna Chaitanya Chundru" <[email protected]>
Send time:Friday, 05/12/2025 20:40:53
To: [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected]
Cc: [email protected], [email protected], [email protected], [email protected]
Subject: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 282 lines · On 12/2/2025 2:34 PM, [email protected] wrote:

From: Senchuan Zhang <[email protected]>

Add driver for the Eswin EIC7700 PCIe host controller, which is based on the DesignWare PCIe core, IP revision 5.96a. The PCIe Gen.3 controller supports a data rate of 8 GT/s and 4 channels, support INTx and MSI interrupts.

---
  drivers/pci/controller/dwc/Kconfig        |  11 +
  drivers/pci/controller/dwc/Makefile       |   1 +
  drivers/pci/controller/dwc/pcie-eic7700.c | 378 ++++++++++++++++++++++
  3 files changed, 390 insertions(+)

create mode 100644 drivers/pci/controller/dwc/pcie-eic7700.c

drivers/pci/controller/dwc/Kconfig +11 -0
index 519b59422b47..c837cb5947b6 100644
@@ -93,6 +93,17 @@ config PCIE_BT1
  	  Enables support for the PCIe controller in the Baikal-T1 SoC to work
  	  in host mode. It's based on the Synopsys DWC PCIe v4.60a IP-core.
 
+config PCIE_EIC7700
+	tristate "Eswin EIC7700 PCIe controller"
+	depends on ARCH_ESWIN || COMPILE_TEST
+	depends on PCI_MSI
+	select PCIE_DW_HOST
+	help
+	  Say Y here if you want PCIe controller support for the Eswin EIC7700.
+	  The PCIe controller on EIC7700 is based on DesignWare hardware,
+	  enables support for the PCIe controller in the EIC7700 SoC to work in
+	  host mode.
+
  config PCI_IMX6
  	bool
 
drivers/pci/controller/dwc/Makefile +1 -0
index 67ba59c02038..7c5a5186ea83 100644
@@ -6,6 +6,7 @@ obj-$(CONFIG_PCIE_DW_EP) += pcie-designware-ep.o
  obj-$(CONFIG_PCIE_DW_PLAT) += pcie-designware-plat.o
  obj-$(CONFIG_PCIE_AMD_MDB) += pcie-amd-mdb.o
  obj-$(CONFIG_PCIE_BT1) += pcie-bt1.o
+obj-$(CONFIG_PCIE_EIC7700) += pcie-eic7700.o
  obj-$(CONFIG_PCI_DRA7XX) += pci-dra7xx.o
  obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
  obj-$(CONFIG_PCIE_FU740) += pcie-fu740.o
drivers/pci/controller/dwc/pcie-eic7700.c new file +225 -0
new file mode 100644
index 000000000000..cb7cdea6a94b
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ESWIN EIC7700 PCIe root complex driver
+ *
+ * Copyright 2025, Beijing ESWIN Computing Technology Co., Ltd.
+ *
+ * Authors: Yu Ning <[email protected]>
+ *          Senchuan Zhang <[email protected]>
+ *          Yanghui Ou <[email protected]>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/resource.h>
+#include <linux/reset.h>
+#include <linux/types.h>
+
+#include "pcie-designware.h"
+
+/* ELBI registers */
+#define PCIEELBI_CTRL0_OFFSET		0x0
+#define PCIEELBI_STATUS0_OFFSET		0x100
+
+/* LTSSM register fields */
+#define PCIEELBI_APP_LTSSM_ENABLE	BIT(5)
+
+/* APP_HOLD_PHY_RST register fields */
+#define PCIEELBI_APP_HOLD_PHY_RST	BIT(6)
+
+/* PM_SEL_AUX_CLK register fields */
+#define PCIEELBI_PM_SEL_AUX_CLK		BIT(16)
+
+/* DEV_TYPE register fields */
+#define PCIEELBI_CTRL0_DEV_TYPE		GENMASK(3, 0)
+
+/* Vendor and device ID value */
+#define PCI_VENDOR_ID_ESWIN		0x1fe1
+#define PCI_DEVICE_ID_ESWIN		0x2030
+
+#define EIC7700_NUM_RSTS		ARRAY_SIZE(eic7700_pcie_rsts)
+
+static const char * const eic7700_pcie_rsts[] = {
+	"pwr",
+	"dbi",
+};
+
+struct eic7700_pcie_data {
+	bool no_pme_handshake;
+};
+
+struct eic7700_pcie_port {
+	struct list_head list;
+	struct reset_control *perst;
+	int num_lanes;
+};
+
+struct eic7700_pcie {
+	struct dw_pcie pci;
+	struct clk_bulk_data *clks;
+	struct reset_control_bulk_data resets[EIC7700_NUM_RSTS];
+	struct list_head ports;
+	const struct eic7700_pcie_data *data;
+	int num_clks;
+};
+
+#define to_eic7700_pcie(x) dev_get_drvdata((x)->dev)
+
+static int eic7700_pcie_start_link(struct dw_pcie *pci)
+{
+	u32 val;
+
+	/* Enable LTSSM */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val |= PCIEELBI_APP_LTSSM_ENABLE;
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	return 0;
+}
+
+static bool eic7700_pcie_link_up(struct dw_pcie *pci)
+{
+	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	u16 val = dw_pcie_readw_dbi(pci, offset + PCI_EXP_LNKSTA);
+
+	return val & PCI_EXP_LNKSTA_DLLLA;
+}
+
+static int eic7700_pcie_perst_reset(struct eic7700_pcie_port *port,
+				    struct eic7700_pcie *pcie)
+{
+	int ret;
+
+	ret = reset_control_assert(port->perst);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to assert PERST#\n");
+		return ret;
+	}
+
+	/* Ensure that PERST# has been asserted for at least 100 ms */
+	msleep(PCIE_T_PVPERL_MS);
+
+	ret = reset_control_deassert(port->perst);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to deassert PERST#\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int eic7700_pcie_parse_port(struct eic7700_pcie *pcie,
+				   struct device_node *node)
+{
+	struct device *dev = pcie->pci.dev;
+	struct eic7700_pcie_port *port;
+
+	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	port->perst = of_reset_control_get_exclusive(node, "perst");
+	if (IS_ERR(port->perst)) {
+		dev_err(dev, "Failed to get PERST# reset\n");
+		return PTR_ERR(port->perst);
+	}
+
+	/*
+	 * TODO: Since the Root Port node is separated out by pcie devicetree,
+	 * the DWC core initialization code can't parse the num-lanes attribute
+	 * in the Root Port. Before entering the DWC core initialization code,
+	 * the platform driver code parses the Root Port node. The EIC7700 only
+	 * supports one Root Port node, and the num-lanes attribute is suitable
+	 * for the case of one Root Rort.
+	 */
+	if (!of_property_read_u32(node, "num-lanes", &port->num_lanes))
+		pcie->pci.num_lanes = port->num_lanes;
+
+	INIT_LIST_HEAD(&port->list);
+	list_add_tail(&port->list, &pcie->ports);
+
+	return 0;
+}
+
+static int eic7700_pcie_parse_ports(struct eic7700_pcie *pcie)
+{
+	struct eic7700_pcie_port *port, *tmp;
+	struct device *dev = pcie->pci.dev;
+	int ret;
+
+	for_each_available_child_of_node_scoped(dev->of_node, of_port) {
+		ret = eic7700_pcie_parse_port(pcie, of_port);
+		if (ret)
+			goto err_port;
+	}
+
+	return 0;
+
+err_port:
+	list_for_each_entry_safe(port, tmp, &pcie->ports, list)
+		list_del(&port->list);
+
+	return ret;
+}
+
+static int eic7700_pcie_host_init(struct dw_pcie_rp *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct eic7700_pcie *pcie = to_eic7700_pcie(pci);
+	struct eic7700_pcie_port *port;
+	u32 val;
+	int ret;
+
+	pcie->num_clks = devm_clk_bulk_get_all_enabled(pci->dev, &pcie->clks);
+	if (pcie->num_clks < 0)
+		return dev_err_probe(pci->dev, pcie->num_clks,
+				     "Failed to get pcie clocks\n");
+
+	/*
+	 * The PWR and DBI Reset signals are respectively used to reset the
+	 * PCIe controller and the DBI registers.
+	 * The PERST# signal is a reset signal that simultaneously controls the
+	 * PCIe controller, PHY, and Endpoint.
+	 * Before configuring the PHY, the PERST# signal must first be
+	 * deasserted.
+	 * The external reference clock is supplied simultaneously to the PHY
+	 * and EP. When the PHY is configurable, the entire chip already has
+	 * stable power and reference clock.
+	 * The PHY will be ready within 20ms after writing app_hold_phy_rst
+	 * register of ELBI register space.
+	 */
+	ret = reset_control_bulk_deassert(EIC7700_NUM_RSTS, pcie->resets);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to deassert resets\n");
+		return ret;
+	}
+
+	/* Configure Root Port type */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val &= ~PCIEELBI_CTRL0_DEV_TYPE;
+	val |= FIELD_PREP(PCIEELBI_CTRL0_DEV_TYPE, PCI_EXP_TYPE_ROOT_PORT);
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	list_for_each_entry(port, &pcie->ports, list) {
+		ret = eic7700_pcie_perst_reset(port, pcie);
+		if (ret)
+			goto err_perst;
+	}
+
+	/* Configure app_hold_phy_rst */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val &= ~PCIEELBI_APP_HOLD_PHY_RST;
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	/* The maximum waiting time for the clock switch lock is 20ms */
+	ret = readl_poll_timeout(pci->elbi_base + PCIEELBI_STATUS0_OFFSET,
+				 val, !(val & PCIEELBI_PM_SEL_AUX_CLK), 1000,
+				 20000);
+	if (ret) {
+		dev_err(pci->dev, "Timeout waiting for PM_SEL_AUX_CLK ready\n");
+		goto err_phy_init;
Quoted 8 lines

drivers/pci/controller/dwc/pcie-eic7700.c line 231

Quoted 6 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +6 -0
+	}
+
+	/*
+	 * Configure ESWIN VID:DID for Root Port as the default values are
+	 * invalid.
+	 */

we need to make dbi registers writeable before this through this API dw_pcie_dbi_ro_wr_en().

Hi, Krishna Chaitanya

Thank you for your comment.
When our driver initialization starts, the BIT(0) of the PCIE_MISC_CONTROL_1_OFF address defaults to 1, allowing for the reading and writing of dbi registers.

Quoted 76 lines
Quoted 76 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +76 -0
+	dw_pcie_writew_dbi(pci, PCI_VENDOR_ID, PCI_VENDOR_ID_ESWIN);
+	dw_pcie_writew_dbi(pci, PCI_DEVICE_ID, PCI_DEVICE_ID_ESWIN);
+
+	return 0;
+
+err_phy_init:
+	list_for_each_entry(port, &pcie->ports, list)
+		reset_control_assert(port->perst);
+err_perst:
+	reset_control_bulk_assert(EIC7700_NUM_RSTS, pcie->resets);
+
+	return ret;
+}
+
+static void eic7700_pcie_host_deinit(struct dw_pcie_rp *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct eic7700_pcie *pcie = to_eic7700_pcie(pci);
+	struct eic7700_pcie_port *port;
+
+	list_for_each_entry(port, &pcie->ports, list)
+		reset_control_assert(port->perst);
+	reset_control_bulk_assert(EIC7700_NUM_RSTS, pcie->resets);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
+}
+
+static const struct dw_pcie_host_ops eic7700_pcie_host_ops = {
+	.init = eic7700_pcie_host_init,
+	.deinit = eic7700_pcie_host_deinit,
+};
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+	.start_link = eic7700_pcie_start_link,
+	.link_up = eic7700_pcie_link_up,
+};
+
+static int eic7700_pcie_probe(struct platform_device *pdev)
+{
+	const struct eic7700_pcie_data *data;
+	struct eic7700_pcie_port *port, *tmp;
+	struct device *dev = &pdev->dev;
+	struct eic7700_pcie *pcie;
+	struct dw_pcie *pci;
+	int ret, i;
+
+	data = of_device_get_match_data(dev);
+	if (!data)
+		return dev_err_probe(dev, -ENODATA, "OF data missing\n");
+
+	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
+	if (!pcie)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&pcie->ports);
+
+	pci = &pcie->pci;
+	pci->dev = dev;
+	pci->ops = &dw_pcie_ops;
+	pci->pp.ops = &eic7700_pcie_host_ops;
+	pcie->data = data;
+	pci->no_pme_handshake = pcie->data->no_pme_handshake;
+
+	for (i = 0; i < EIC7700_NUM_RSTS; i++)
+		pcie->resets[i].id = eic7700_pcie_rsts[i];
+
+	ret = devm_reset_control_bulk_get_exclusive(dev, EIC7700_NUM_RSTS,
+						    pcie->resets);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to get resets\n");
+
+	ret = eic7700_pcie_parse_ports(pcie);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Failed to parse Root Port: %d\n", ret);
+
+	platform_set_drvdata(pdev, pcie);
Quoted 8 lines

drivers/pci/controller/dwc/pcie-eic7700.c line 313

Quoted 6 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +6 -0
+
+	pm_runtime_no_callbacks(dev);
+	devm_pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0)
+		goto err_pm_runtime_put;

Any specific reason why we are enabling runtime pm and doing pm_runtime_get_sync()

To avoid warnings when the driver starts, pm_runtime_get_sync() has been added. Warnings as follows:

"pci0000:00: runtime PM trying to activate child device pci0000:00 but parent (54000000.pcie) is not active"

Kind regards,
Senchuan Zhang

Quoted 65 lines
Quoted 65 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +65 -0
+
+	ret = dw_pcie_host_init(&pci->pp);
+	if (ret) {
+		dev_err(dev, "Failed to initialize host\n");
+		goto err_init;
+	}
+
+	return 0;
+
+err_init:
+	list_for_each_entry_safe(port, tmp, &pcie->ports, list) {
+		list_del(&port->list);
+		reset_control_put(port->perst);
+	}
+err_pm_runtime_put:
+	pm_runtime_put(dev);
+
+	return ret;
+}
+
+static int eic7700_pcie_suspend_noirq(struct device *dev)
+{
+	struct eic7700_pcie *pcie = dev_get_drvdata(dev);
+
+	return dw_pcie_suspend_noirq(&pcie->pci);
+}
+
+static int eic7700_pcie_resume_noirq(struct device *dev)
+{
+	struct eic7700_pcie *pcie = dev_get_drvdata(dev);
+
+	return dw_pcie_resume_noirq(&pcie->pci);
+}
+
+static const struct dev_pm_ops eic7700_pcie_pm_ops = {
+	NOIRQ_SYSTEM_SLEEP_PM_OPS(eic7700_pcie_suspend_noirq,
+				  eic7700_pcie_resume_noirq)
+};
+
+static const struct eic7700_pcie_data eic7700_data = {
+	.no_pme_handshake = true,
+};
+
+static const struct of_device_id eic7700_pcie_of_match[] = {
+	{ .compatible = "eswin,eic7700-pcie", .data = &eic7700_data },
+	{},
+};
+
+static struct platform_driver eic7700_pcie_driver = {
+	.probe = eic7700_pcie_probe,
+	.driver = {
+		.name = "eic7700-pcie",
+		.of_match_table = eic7700_pcie_of_match,
+		.suppress_bind_attrs = true,
+		.pm = &eic7700_pcie_pm_ops,
+		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
+	},
+};
+builtin_platform_driver(eic7700_pcie_driver);
+
+MODULE_DESCRIPTION("Eswin EIC7700 PCIe host controller driver");
+MODULE_AUTHOR("Yu Ning <[email protected]>");
+MODULE_AUTHOR("Senchuan Zhang <[email protected]>");
+MODULE_AUTHOR("Yanghui Ou <[email protected]>");
+MODULE_LICENSE("GPL");
#5 lore raw

Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 302 lines · zhangsenchuan
Quoted 294 lines

-----Original Messages-----
From: "Krishna Chaitanya Chundru" <[email protected]>
Send time:Friday, 05/12/2025 20:40:53
To: [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected]
Cc: [email protected], [email protected], [email protected], [email protected]
Subject: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 282 lines · On 12/2/2025 2:34 PM, [email protected] wrote:

From: Senchuan Zhang <[email protected]>

Add driver for the Eswin EIC7700 PCIe host controller, which is based on the DesignWare PCIe core, IP revision 5.96a. The PCIe Gen.3 controller supports a data rate of 8 GT/s and 4 channels, support INTx and MSI interrupts.

---
   drivers/pci/controller/dwc/Kconfig        |  11 +
   drivers/pci/controller/dwc/Makefile       |   1 +
   drivers/pci/controller/dwc/pcie-eic7700.c | 378 ++++++++++++++++++++++
   3 files changed, 390 insertions(+)

create mode 100644 drivers/pci/controller/dwc/pcie-eic7700.c

drivers/pci/controller/dwc/Kconfig +11 -0
index 519b59422b47..c837cb5947b6 100644
@@ -93,6 +93,17 @@ config PCIE_BT1
   	  Enables support for the PCIe controller in the Baikal-T1 SoC to work
   	  in host mode. It's based on the Synopsys DWC PCIe v4.60a IP-core.
 
+config PCIE_EIC7700
+	tristate "Eswin EIC7700 PCIe controller"
+	depends on ARCH_ESWIN || COMPILE_TEST
+	depends on PCI_MSI
+	select PCIE_DW_HOST
+	help
+	  Say Y here if you want PCIe controller support for the Eswin EIC7700.
+	  The PCIe controller on EIC7700 is based on DesignWare hardware,
+	  enables support for the PCIe controller in the EIC7700 SoC to work in
+	  host mode.
+
   config PCI_IMX6
   	bool
 
drivers/pci/controller/dwc/Makefile +1 -0
index 67ba59c02038..7c5a5186ea83 100644
@@ -6,6 +6,7 @@ obj-$(CONFIG_PCIE_DW_EP) += pcie-designware-ep.o
   obj-$(CONFIG_PCIE_DW_PLAT) += pcie-designware-plat.o
   obj-$(CONFIG_PCIE_AMD_MDB) += pcie-amd-mdb.o
   obj-$(CONFIG_PCIE_BT1) += pcie-bt1.o
+obj-$(CONFIG_PCIE_EIC7700) += pcie-eic7700.o
   obj-$(CONFIG_PCI_DRA7XX) += pci-dra7xx.o
   obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
   obj-$(CONFIG_PCIE_FU740) += pcie-fu740.o
drivers/pci/controller/dwc/pcie-eic7700.c new file +225 -0
new file mode 100644
index 000000000000..cb7cdea6a94b
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ESWIN EIC7700 PCIe root complex driver
+ *
+ * Copyright 2025, Beijing ESWIN Computing Technology Co., Ltd.
+ *
+ * Authors: Yu Ning <[email protected]>
+ *          Senchuan Zhang <[email protected]>
+ *          Yanghui Ou <[email protected]>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/resource.h>
+#include <linux/reset.h>
+#include <linux/types.h>
+
+#include "pcie-designware.h"
+
+/* ELBI registers */
+#define PCIEELBI_CTRL0_OFFSET		0x0
+#define PCIEELBI_STATUS0_OFFSET		0x100
+
+/* LTSSM register fields */
+#define PCIEELBI_APP_LTSSM_ENABLE	BIT(5)
+
+/* APP_HOLD_PHY_RST register fields */
+#define PCIEELBI_APP_HOLD_PHY_RST	BIT(6)
+
+/* PM_SEL_AUX_CLK register fields */
+#define PCIEELBI_PM_SEL_AUX_CLK		BIT(16)
+
+/* DEV_TYPE register fields */
+#define PCIEELBI_CTRL0_DEV_TYPE		GENMASK(3, 0)
+
+/* Vendor and device ID value */
+#define PCI_VENDOR_ID_ESWIN		0x1fe1
+#define PCI_DEVICE_ID_ESWIN		0x2030
+
+#define EIC7700_NUM_RSTS		ARRAY_SIZE(eic7700_pcie_rsts)
+
+static const char * const eic7700_pcie_rsts[] = {
+	"pwr",
+	"dbi",
+};
+
+struct eic7700_pcie_data {
+	bool no_pme_handshake;
+};
+
+struct eic7700_pcie_port {
+	struct list_head list;
+	struct reset_control *perst;
+	int num_lanes;
+};
+
+struct eic7700_pcie {
+	struct dw_pcie pci;
+	struct clk_bulk_data *clks;
+	struct reset_control_bulk_data resets[EIC7700_NUM_RSTS];
+	struct list_head ports;
+	const struct eic7700_pcie_data *data;
+	int num_clks;
+};
+
+#define to_eic7700_pcie(x) dev_get_drvdata((x)->dev)
+
+static int eic7700_pcie_start_link(struct dw_pcie *pci)
+{
+	u32 val;
+
+	/* Enable LTSSM */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val |= PCIEELBI_APP_LTSSM_ENABLE;
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	return 0;
+}
+
+static bool eic7700_pcie_link_up(struct dw_pcie *pci)
+{
+	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	u16 val = dw_pcie_readw_dbi(pci, offset + PCI_EXP_LNKSTA);
+
+	return val & PCI_EXP_LNKSTA_DLLLA;
+}
+
+static int eic7700_pcie_perst_reset(struct eic7700_pcie_port *port,
+				    struct eic7700_pcie *pcie)
+{
+	int ret;
+
+	ret = reset_control_assert(port->perst);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to assert PERST#\n");
+		return ret;
+	}
+
+	/* Ensure that PERST# has been asserted for at least 100 ms */
+	msleep(PCIE_T_PVPERL_MS);
+
+	ret = reset_control_deassert(port->perst);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to deassert PERST#\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int eic7700_pcie_parse_port(struct eic7700_pcie *pcie,
+				   struct device_node *node)
+{
+	struct device *dev = pcie->pci.dev;
+	struct eic7700_pcie_port *port;
+
+	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	port->perst = of_reset_control_get_exclusive(node, "perst");
+	if (IS_ERR(port->perst)) {
+		dev_err(dev, "Failed to get PERST# reset\n");
+		return PTR_ERR(port->perst);
+	}
+
+	/*
+	 * TODO: Since the Root Port node is separated out by pcie devicetree,
+	 * the DWC core initialization code can't parse the num-lanes attribute
+	 * in the Root Port. Before entering the DWC core initialization code,
+	 * the platform driver code parses the Root Port node. The EIC7700 only
+	 * supports one Root Port node, and the num-lanes attribute is suitable
+	 * for the case of one Root Rort.
+	 */
+	if (!of_property_read_u32(node, "num-lanes", &port->num_lanes))
+		pcie->pci.num_lanes = port->num_lanes;
+
+	INIT_LIST_HEAD(&port->list);
+	list_add_tail(&port->list, &pcie->ports);
+
+	return 0;
+}
+
+static int eic7700_pcie_parse_ports(struct eic7700_pcie *pcie)
+{
+	struct eic7700_pcie_port *port, *tmp;
+	struct device *dev = pcie->pci.dev;
+	int ret;
+
+	for_each_available_child_of_node_scoped(dev->of_node, of_port) {
+		ret = eic7700_pcie_parse_port(pcie, of_port);
+		if (ret)
+			goto err_port;
+	}
+
+	return 0;
+
+err_port:
+	list_for_each_entry_safe(port, tmp, &pcie->ports, list)
+		list_del(&port->list);
+
+	return ret;
+}
+
+static int eic7700_pcie_host_init(struct dw_pcie_rp *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct eic7700_pcie *pcie = to_eic7700_pcie(pci);
+	struct eic7700_pcie_port *port;
+	u32 val;
+	int ret;
+
+	pcie->num_clks = devm_clk_bulk_get_all_enabled(pci->dev, &pcie->clks);
+	if (pcie->num_clks < 0)
+		return dev_err_probe(pci->dev, pcie->num_clks,
+				     "Failed to get pcie clocks\n");
+
+	/*
+	 * The PWR and DBI Reset signals are respectively used to reset the
+	 * PCIe controller and the DBI registers.
+	 * The PERST# signal is a reset signal that simultaneously controls the
+	 * PCIe controller, PHY, and Endpoint.
+	 * Before configuring the PHY, the PERST# signal must first be
+	 * deasserted.
+	 * The external reference clock is supplied simultaneously to the PHY
+	 * and EP. When the PHY is configurable, the entire chip already has
+	 * stable power and reference clock.
+	 * The PHY will be ready within 20ms after writing app_hold_phy_rst
+	 * register of ELBI register space.
+	 */
+	ret = reset_control_bulk_deassert(EIC7700_NUM_RSTS, pcie->resets);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to deassert resets\n");
+		return ret;
+	}
+
+	/* Configure Root Port type */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val &= ~PCIEELBI_CTRL0_DEV_TYPE;
+	val |= FIELD_PREP(PCIEELBI_CTRL0_DEV_TYPE, PCI_EXP_TYPE_ROOT_PORT);
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	list_for_each_entry(port, &pcie->ports, list) {
+		ret = eic7700_pcie_perst_reset(port, pcie);
+		if (ret)
+			goto err_perst;
+	}
+
+	/* Configure app_hold_phy_rst */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val &= ~PCIEELBI_APP_HOLD_PHY_RST;
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	/* The maximum waiting time for the clock switch lock is 20ms */
+	ret = readl_poll_timeout(pci->elbi_base + PCIEELBI_STATUS0_OFFSET,
+				 val, !(val & PCIEELBI_PM_SEL_AUX_CLK), 1000,
+				 20000);
+	if (ret) {
+		dev_err(pci->dev, "Timeout waiting for PM_SEL_AUX_CLK ready\n");
+		goto err_phy_init;
Quoted 8 lines

drivers/pci/controller/dwc/pcie-eic7700.c line 231

Quoted 6 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +6 -0
+	}
+
+	/*
+	 * Configure ESWIN VID:DID for Root Port as the default values are
+	 * invalid.
+	 */

we need to make dbi registers writeable before this through this API dw_pcie_dbi_ro_wr_en().

Quoted 6 lines

Hi, Krishna Chaitanya

Thank you for your comment.
When our driver initialization starts, the BIT(0) of the PCIE_MISC_CONTROL_1_OFF address defaults to 1, allowing for the reading and writing of dbi registers.

Thanks for the info, then in that case do we need to clear it before enumeration?

-  Krishna Chaitanya.

Quoted 158 lines
Quoted 76 lines
Quoted 76 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +76 -0
+	dw_pcie_writew_dbi(pci, PCI_VENDOR_ID, PCI_VENDOR_ID_ESWIN);
+	dw_pcie_writew_dbi(pci, PCI_DEVICE_ID, PCI_DEVICE_ID_ESWIN);
+
+	return 0;
+
+err_phy_init:
+	list_for_each_entry(port, &pcie->ports, list)
+		reset_control_assert(port->perst);
+err_perst:
+	reset_control_bulk_assert(EIC7700_NUM_RSTS, pcie->resets);
+
+	return ret;
+}
+
+static void eic7700_pcie_host_deinit(struct dw_pcie_rp *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct eic7700_pcie *pcie = to_eic7700_pcie(pci);
+	struct eic7700_pcie_port *port;
+
+	list_for_each_entry(port, &pcie->ports, list)
+		reset_control_assert(port->perst);
+	reset_control_bulk_assert(EIC7700_NUM_RSTS, pcie->resets);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
+}
+
+static const struct dw_pcie_host_ops eic7700_pcie_host_ops = {
+	.init = eic7700_pcie_host_init,
+	.deinit = eic7700_pcie_host_deinit,
+};
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+	.start_link = eic7700_pcie_start_link,
+	.link_up = eic7700_pcie_link_up,
+};
+
+static int eic7700_pcie_probe(struct platform_device *pdev)
+{
+	const struct eic7700_pcie_data *data;
+	struct eic7700_pcie_port *port, *tmp;
+	struct device *dev = &pdev->dev;
+	struct eic7700_pcie *pcie;
+	struct dw_pcie *pci;
+	int ret, i;
+
+	data = of_device_get_match_data(dev);
+	if (!data)
+		return dev_err_probe(dev, -ENODATA, "OF data missing\n");
+
+	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
+	if (!pcie)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&pcie->ports);
+
+	pci = &pcie->pci;
+	pci->dev = dev;
+	pci->ops = &dw_pcie_ops;
+	pci->pp.ops = &eic7700_pcie_host_ops;
+	pcie->data = data;
+	pci->no_pme_handshake = pcie->data->no_pme_handshake;
+
+	for (i = 0; i < EIC7700_NUM_RSTS; i++)
+		pcie->resets[i].id = eic7700_pcie_rsts[i];
+
+	ret = devm_reset_control_bulk_get_exclusive(dev, EIC7700_NUM_RSTS,
+						    pcie->resets);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to get resets\n");
+
+	ret = eic7700_pcie_parse_ports(pcie);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Failed to parse Root Port: %d\n", ret);
+
+	platform_set_drvdata(pdev, pcie);
Quoted 8 lines

drivers/pci/controller/dwc/pcie-eic7700.c line 313

Quoted 6 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +6 -0
+
+	pm_runtime_no_callbacks(dev);
+	devm_pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0)
+		goto err_pm_runtime_put;

Any specific reason why we are enabling runtime pm and doing pm_runtime_get_sync()

To avoid warnings when the driver starts, pm_runtime_get_sync() has been added. Warnings as follows:

"pci0000:00: runtime PM trying to activate child device pci0000:00 but parent (54000000.pcie) is not active"

Kind regards,
Senchuan Zhang

Quoted 65 lines
Quoted 65 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +65 -0
+
+	ret = dw_pcie_host_init(&pci->pp);
+	if (ret) {
+		dev_err(dev, "Failed to initialize host\n");
+		goto err_init;
+	}
+
+	return 0;
+
+err_init:
+	list_for_each_entry_safe(port, tmp, &pcie->ports, list) {
+		list_del(&port->list);
+		reset_control_put(port->perst);
+	}
+err_pm_runtime_put:
+	pm_runtime_put(dev);
+
+	return ret;
+}
+
+static int eic7700_pcie_suspend_noirq(struct device *dev)
+{
+	struct eic7700_pcie *pcie = dev_get_drvdata(dev);
+
+	return dw_pcie_suspend_noirq(&pcie->pci);
+}
+
+static int eic7700_pcie_resume_noirq(struct device *dev)
+{
+	struct eic7700_pcie *pcie = dev_get_drvdata(dev);
+
+	return dw_pcie_resume_noirq(&pcie->pci);
+}
+
+static const struct dev_pm_ops eic7700_pcie_pm_ops = {
+	NOIRQ_SYSTEM_SLEEP_PM_OPS(eic7700_pcie_suspend_noirq,
+				  eic7700_pcie_resume_noirq)
+};
+
+static const struct eic7700_pcie_data eic7700_data = {
+	.no_pme_handshake = true,
+};
+
+static const struct of_device_id eic7700_pcie_of_match[] = {
+	{ .compatible = "eswin,eic7700-pcie", .data = &eic7700_data },
+	{},
+};
+
+static struct platform_driver eic7700_pcie_driver = {
+	.probe = eic7700_pcie_probe,
+	.driver = {
+		.name = "eic7700-pcie",
+		.of_match_table = eic7700_pcie_of_match,
+		.suppress_bind_attrs = true,
+		.pm = &eic7700_pcie_pm_ops,
+		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
+	},
+};
+builtin_platform_driver(eic7700_pcie_driver);
+
+MODULE_DESCRIPTION("Eswin EIC7700 PCIe host controller driver");
+MODULE_AUTHOR("Yu Ning <[email protected]>");
+MODULE_AUTHOR("Senchuan Zhang <[email protected]>");
+MODULE_AUTHOR("Yanghui Ou <[email protected]>");
+MODULE_LICENSE("GPL");
#6 lore raw

Re: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 315 lines

-----Original Messages-----
From: "Krishna Chaitanya Chundru" <[email protected]>
Send time:Monday, 08/12/2025 22:13:13
To: zhangsenchuan <[email protected]>
Cc: [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected]
Subject: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 302 lines · zhangsenchuan
Quoted 302 lines

-----Original Messages-----
From: "Krishna Chaitanya Chundru" <[email protected]>
Send time:Friday, 05/12/2025 20:40:53
To: [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected]
Cc: [email protected], [email protected], [email protected], [email protected]
Subject: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 278 lines · On 12/2/2025 2:34 PM, [email protected] wrote:

From: Senchuan Zhang <[email protected]>

Add driver for the Eswin EIC7700 PCIe host controller, which is based on the DesignWare PCIe core, IP revision 5.96a. The PCIe Gen.3 controller supports a data rate of 8 GT/s and 4 channels, support INTx and MSI interrupts.

---
   drivers/pci/controller/dwc/Kconfig        |  11 +
   drivers/pci/controller/dwc/Makefile       |   1 +
   drivers/pci/controller/dwc/pcie-eic7700.c | 378 ++++++++++++++++++++++
   3 files changed, 390 insertions(+)

create mode 100644 drivers/pci/controller/dwc/pcie-eic7700.c

drivers/pci/controller/dwc/Kconfig +11 -0
index 519b59422b47..c837cb5947b6 100644
@@ -93,6 +93,17 @@ config PCIE_BT1
   	  Enables support for the PCIe controller in the Baikal-T1 SoC to work
   	  in host mode. It's based on the Synopsys DWC PCIe v4.60a IP-core.
 
+config PCIE_EIC7700
+	tristate "Eswin EIC7700 PCIe controller"
+	depends on ARCH_ESWIN || COMPILE_TEST
+	depends on PCI_MSI
+	select PCIE_DW_HOST
+	help
+	  Say Y here if you want PCIe controller support for the Eswin EIC7700.
+	  The PCIe controller on EIC7700 is based on DesignWare hardware,
+	  enables support for the PCIe controller in the EIC7700 SoC to work in
+	  host mode.
+
   config PCI_IMX6
   	bool
 
drivers/pci/controller/dwc/Makefile +1 -0
index 67ba59c02038..7c5a5186ea83 100644
@@ -6,6 +6,7 @@ obj-$(CONFIG_PCIE_DW_EP) += pcie-designware-ep.o
   obj-$(CONFIG_PCIE_DW_PLAT) += pcie-designware-plat.o
   obj-$(CONFIG_PCIE_AMD_MDB) += pcie-amd-mdb.o
   obj-$(CONFIG_PCIE_BT1) += pcie-bt1.o
+obj-$(CONFIG_PCIE_EIC7700) += pcie-eic7700.o
   obj-$(CONFIG_PCI_DRA7XX) += pci-dra7xx.o
   obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
   obj-$(CONFIG_PCIE_FU740) += pcie-fu740.o
drivers/pci/controller/dwc/pcie-eic7700.c new file +221 -0
new file mode 100644
index 000000000000..cb7cdea6a94b
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ESWIN EIC7700 PCIe root complex driver
+ *
+ * Copyright 2025, Beijing ESWIN Computing Technology Co., Ltd.
+ *
+ * Authors: Yu Ning <[email protected]>
+ *          Senchuan Zhang <[email protected]>
+ *          Yanghui Ou <[email protected]>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/resource.h>
+#include <linux/reset.h>
+#include <linux/types.h>
+
+#include "pcie-designware.h"
+
+/* ELBI registers */
+#define PCIEELBI_CTRL0_OFFSET		0x0
+#define PCIEELBI_STATUS0_OFFSET		0x100
+
+/* LTSSM register fields */
+#define PCIEELBI_APP_LTSSM_ENABLE	BIT(5)
+
+/* APP_HOLD_PHY_RST register fields */
+#define PCIEELBI_APP_HOLD_PHY_RST	BIT(6)
+
+/* PM_SEL_AUX_CLK register fields */
+#define PCIEELBI_PM_SEL_AUX_CLK		BIT(16)
+
+/* DEV_TYPE register fields */
+#define PCIEELBI_CTRL0_DEV_TYPE		GENMASK(3, 0)
+
+/* Vendor and device ID value */
+#define PCI_VENDOR_ID_ESWIN		0x1fe1
+#define PCI_DEVICE_ID_ESWIN		0x2030
+
+#define EIC7700_NUM_RSTS		ARRAY_SIZE(eic7700_pcie_rsts)
+
+static const char * const eic7700_pcie_rsts[] = {
+	"pwr",
+	"dbi",
+};
+
+struct eic7700_pcie_data {
+	bool no_pme_handshake;
+};
+
+struct eic7700_pcie_port {
+	struct list_head list;
+	struct reset_control *perst;
+	int num_lanes;
+};
+
+struct eic7700_pcie {
+	struct dw_pcie pci;
+	struct clk_bulk_data *clks;
+	struct reset_control_bulk_data resets[EIC7700_NUM_RSTS];
+	struct list_head ports;
+	const struct eic7700_pcie_data *data;
+	int num_clks;
+};
+
+#define to_eic7700_pcie(x) dev_get_drvdata((x)->dev)
+
+static int eic7700_pcie_start_link(struct dw_pcie *pci)
+{
+	u32 val;
+
+	/* Enable LTSSM */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val |= PCIEELBI_APP_LTSSM_ENABLE;
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	return 0;
+}
+
+static bool eic7700_pcie_link_up(struct dw_pcie *pci)
+{
+	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	u16 val = dw_pcie_readw_dbi(pci, offset + PCI_EXP_LNKSTA);
+
+	return val & PCI_EXP_LNKSTA_DLLLA;
+}
+
+static int eic7700_pcie_perst_reset(struct eic7700_pcie_port *port,
+				    struct eic7700_pcie *pcie)
+{
+	int ret;
+
+	ret = reset_control_assert(port->perst);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to assert PERST#\n");
+		return ret;
+	}
+
+	/* Ensure that PERST# has been asserted for at least 100 ms */
+	msleep(PCIE_T_PVPERL_MS);
+
+	ret = reset_control_deassert(port->perst);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to deassert PERST#\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int eic7700_pcie_parse_port(struct eic7700_pcie *pcie,
+				   struct device_node *node)
+{
+	struct device *dev = pcie->pci.dev;
+	struct eic7700_pcie_port *port;
+
+	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	port->perst = of_reset_control_get_exclusive(node, "perst");
+	if (IS_ERR(port->perst)) {
+		dev_err(dev, "Failed to get PERST# reset\n");
+		return PTR_ERR(port->perst);
+	}
+
+	/*
+	 * TODO: Since the Root Port node is separated out by pcie devicetree,
+	 * the DWC core initialization code can't parse the num-lanes attribute
+	 * in the Root Port. Before entering the DWC core initialization code,
+	 * the platform driver code parses the Root Port node. The EIC7700 only
+	 * supports one Root Port node, and the num-lanes attribute is suitable
+	 * for the case of one Root Rort.
+	 */
+	if (!of_property_read_u32(node, "num-lanes", &port->num_lanes))
+		pcie->pci.num_lanes = port->num_lanes;
+
+	INIT_LIST_HEAD(&port->list);
+	list_add_tail(&port->list, &pcie->ports);
+
+	return 0;
+}
+
+static int eic7700_pcie_parse_ports(struct eic7700_pcie *pcie)
+{
+	struct eic7700_pcie_port *port, *tmp;
+	struct device *dev = pcie->pci.dev;
+	int ret;
+
+	for_each_available_child_of_node_scoped(dev->of_node, of_port) {
+		ret = eic7700_pcie_parse_port(pcie, of_port);
+		if (ret)
+			goto err_port;
+	}
+
+	return 0;
+
+err_port:
+	list_for_each_entry_safe(port, tmp, &pcie->ports, list)
+		list_del(&port->list);
+
+	return ret;
+}
+
+static int eic7700_pcie_host_init(struct dw_pcie_rp *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct eic7700_pcie *pcie = to_eic7700_pcie(pci);
+	struct eic7700_pcie_port *port;
+	u32 val;
+	int ret;
+
+	pcie->num_clks = devm_clk_bulk_get_all_enabled(pci->dev, &pcie->clks);
+	if (pcie->num_clks < 0)
+		return dev_err_probe(pci->dev, pcie->num_clks,
+				     "Failed to get pcie clocks\n");
+
+	/*
+	 * The PWR and DBI Reset signals are respectively used to reset the
+	 * PCIe controller and the DBI registers.
+	 * The PERST# signal is a reset signal that simultaneously controls the
+	 * PCIe controller, PHY, and Endpoint.
+	 * Before configuring the PHY, the PERST# signal must first be
+	 * deasserted.
+	 * The external reference clock is supplied simultaneously to the PHY
+	 * and EP. When the PHY is configurable, the entire chip already has
+	 * stable power and reference clock.
+	 * The PHY will be ready within 20ms after writing app_hold_phy_rst
+	 * register of ELBI register space.
+	 */
+	ret = reset_control_bulk_deassert(EIC7700_NUM_RSTS, pcie->resets);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to deassert resets\n");
+		return ret;
+	}
+
+	/* Configure Root Port type */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val &= ~PCIEELBI_CTRL0_DEV_TYPE;
+	val |= FIELD_PREP(PCIEELBI_CTRL0_DEV_TYPE, PCI_EXP_TYPE_ROOT_PORT);
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	list_for_each_entry(port, &pcie->ports, list) {
+		ret = eic7700_pcie_perst_reset(port, pcie);
+		if (ret)
+			goto err_perst;
+	}
+
+	/* Configure app_hold_phy_rst */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val &= ~PCIEELBI_APP_HOLD_PHY_RST;
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	/* The maximum waiting time for the clock switch lock is 20ms */
+	ret = readl_poll_timeout(pci->elbi_base + PCIEELBI_STATUS0_OFFSET,
+				 val, !(val & PCIEELBI_PM_SEL_AUX_CLK), 1000,

drivers/pci/controller/dwc/pcie-eic7700.c line 231

Quoted 10 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +10 -0
+				 20000);
+	if (ret) {
+		dev_err(pci->dev, "Timeout waiting for PM_SEL_AUX_CLK ready\n");
+		goto err_phy_init;
+	}
+
+	/*
+	 * Configure ESWIN VID:DID for Root Port as the default values are
+	 * invalid.
+	 */

we need to make dbi registers writeable before this through this API dw_pcie_dbi_ro_wr_en().

Quoted 8 lines
Quoted 6 lines

Hi, Krishna Chaitanya

Thank you for your comment.
When our driver initialization starts, the BIT(0) of the PCIE_MISC_CONTROL_1_OFF address defaults to 1, allowing for the reading and writing of dbi registers.

Thanks for the info, then in that case do we need to clear it before enumeration?

Thank you for the reminder.
Do you mean that after executing the dw_pcie_writew_dbi function, dw_pcie_dbi_ro_wr_dis() should be called to clear the writable bits of dbi?

Kind regards,
Senchuan Zhang

Quoted 159 lines
Quoted 159 lines
Quoted 77 lines
Quoted 77 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +76 -0
+	dw_pcie_writew_dbi(pci, PCI_VENDOR_ID, PCI_VENDOR_ID_ESWIN);
+	dw_pcie_writew_dbi(pci, PCI_DEVICE_ID, PCI_DEVICE_ID_ESWIN);
+
+	return 0;
+
+err_phy_init:
+	list_for_each_entry(port, &pcie->ports, list)
+		reset_control_assert(port->perst);
+err_perst:
+	reset_control_bulk_assert(EIC7700_NUM_RSTS, pcie->resets);
+
+	return ret;
+}
+
+static void eic7700_pcie_host_deinit(struct dw_pcie_rp *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct eic7700_pcie *pcie = to_eic7700_pcie(pci);
+	struct eic7700_pcie_port *port;
+
+	list_for_each_entry(port, &pcie->ports, list)
+		reset_control_assert(port->perst);
+	reset_control_bulk_assert(EIC7700_NUM_RSTS, pcie->resets);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
+}
+
+static const struct dw_pcie_host_ops eic7700_pcie_host_ops = {
+	.init = eic7700_pcie_host_init,
+	.deinit = eic7700_pcie_host_deinit,
+};
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+	.start_link = eic7700_pcie_start_link,
+	.link_up = eic7700_pcie_link_up,
+};
+
+static int eic7700_pcie_probe(struct platform_device *pdev)
+{
+	const struct eic7700_pcie_data *data;
+	struct eic7700_pcie_port *port, *tmp;
+	struct device *dev = &pdev->dev;
+	struct eic7700_pcie *pcie;
+	struct dw_pcie *pci;
+	int ret, i;
+
+	data = of_device_get_match_data(dev);
+	if (!data)
+		return dev_err_probe(dev, -ENODATA, "OF data missing\n");
+
+	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
+	if (!pcie)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&pcie->ports);
+
+	pci = &pcie->pci;
+	pci->dev = dev;
+	pci->ops = &dw_pcie_ops;
+	pci->pp.ops = &eic7700_pcie_host_ops;
+	pcie->data = data;
+	pci->no_pme_handshake = pcie->data->no_pme_handshake;
+
+	for (i = 0; i < EIC7700_NUM_RSTS; i++)
+		pcie->resets[i].id = eic7700_pcie_rsts[i];
+
+	ret = devm_reset_control_bulk_get_exclusive(dev, EIC7700_NUM_RSTS,
+						    pcie->resets);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to get resets\n");
+
+	ret = eic7700_pcie_parse_ports(pcie);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Failed to parse Root Port: %d\n", ret);
+
+	platform_set_drvdata(pdev, pcie);
Quoted 8 lines

drivers/pci/controller/dwc/pcie-eic7700.c line 313

Quoted 6 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +6 -0
+
+	pm_runtime_no_callbacks(dev);
+	devm_pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0)
+		goto err_pm_runtime_put;

Any specific reason why we are enabling runtime pm and doing pm_runtime_get_sync()

To avoid warnings when the driver starts, pm_runtime_get_sync() has been added. Warnings as follows:

"pci0000:00: runtime PM trying to activate child device pci0000:00 but parent (54000000.pcie) is not active"

Kind regards,
Senchuan Zhang

Quoted 65 lines
Quoted 65 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +65 -0
+
+	ret = dw_pcie_host_init(&pci->pp);
+	if (ret) {
+		dev_err(dev, "Failed to initialize host\n");
+		goto err_init;
+	}
+
+	return 0;
+
+err_init:
+	list_for_each_entry_safe(port, tmp, &pcie->ports, list) {
+		list_del(&port->list);
+		reset_control_put(port->perst);
+	}
+err_pm_runtime_put:
+	pm_runtime_put(dev);
+
+	return ret;
+}
+
+static int eic7700_pcie_suspend_noirq(struct device *dev)
+{
+	struct eic7700_pcie *pcie = dev_get_drvdata(dev);
+
+	return dw_pcie_suspend_noirq(&pcie->pci);
+}
+
+static int eic7700_pcie_resume_noirq(struct device *dev)
+{
+	struct eic7700_pcie *pcie = dev_get_drvdata(dev);
+
+	return dw_pcie_resume_noirq(&pcie->pci);
+}
+
+static const struct dev_pm_ops eic7700_pcie_pm_ops = {
+	NOIRQ_SYSTEM_SLEEP_PM_OPS(eic7700_pcie_suspend_noirq,
+				  eic7700_pcie_resume_noirq)
+};
+
+static const struct eic7700_pcie_data eic7700_data = {
+	.no_pme_handshake = true,
+};
+
+static const struct of_device_id eic7700_pcie_of_match[] = {
+	{ .compatible = "eswin,eic7700-pcie", .data = &eic7700_data },
+	{},
+};
+
+static struct platform_driver eic7700_pcie_driver = {
+	.probe = eic7700_pcie_probe,
+	.driver = {
+		.name = "eic7700-pcie",
+		.of_match_table = eic7700_pcie_of_match,
+		.suppress_bind_attrs = true,
+		.pm = &eic7700_pcie_pm_ops,
+		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
+	},
+};
+builtin_platform_driver(eic7700_pcie_driver);
+
+MODULE_DESCRIPTION("Eswin EIC7700 PCIe host controller driver");
+MODULE_AUTHOR("Yu Ning <[email protected]>");
+MODULE_AUTHOR("Senchuan Zhang <[email protected]>");
+MODULE_AUTHOR("Yanghui Ou <[email protected]>");
+MODULE_LICENSE("GPL");
#7 lore raw

Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 319 lines · zhangsenchuan
Quoted 319 lines

-----Original Messages-----
From: "Krishna Chaitanya Chundru" <[email protected]>
Send time:Monday, 08/12/2025 22:13:13
To: zhangsenchuan <[email protected]>
Cc: [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected]
Subject: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 307 lines · zhangsenchuan
Quoted 293 lines

-----Original Messages-----
From: "Krishna Chaitanya Chundru" <[email protected]>
Send time:Friday, 05/12/2025 20:40:53
To: [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected]
Cc: [email protected], [email protected], [email protected], [email protected]
Subject: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 282 lines · On 12/2/2025 2:34 PM, [email protected] wrote:

From: Senchuan Zhang <[email protected]>

Add driver for the Eswin EIC7700 PCIe host controller, which is based on the DesignWare PCIe core, IP revision 5.96a. The PCIe Gen.3 controller supports a data rate of 8 GT/s and 4 channels, support INTx and MSI interrupts.

---
    drivers/pci/controller/dwc/Kconfig        |  11 +
    drivers/pci/controller/dwc/Makefile       |   1 +
    drivers/pci/controller/dwc/pcie-eic7700.c | 378 ++++++++++++++++++++++
    3 files changed, 390 insertions(+)
    create mode 100644 drivers/pci/controller/dwc/pcie-eic7700.c
drivers/pci/controller/dwc/Kconfig +11 -0
index 519b59422b47..c837cb5947b6 100644
@@ -93,6 +93,17 @@ config PCIE_BT1
    	  Enables support for the PCIe controller in the Baikal-T1 SoC to work
    	  in host mode. It's based on the Synopsys DWC PCIe v4.60a IP-core.
 
+config PCIE_EIC7700
+	tristate "Eswin EIC7700 PCIe controller"
+	depends on ARCH_ESWIN || COMPILE_TEST
+	depends on PCI_MSI
+	select PCIE_DW_HOST
+	help
+	  Say Y here if you want PCIe controller support for the Eswin EIC7700.
+	  The PCIe controller on EIC7700 is based on DesignWare hardware,
+	  enables support for the PCIe controller in the EIC7700 SoC to work in
+	  host mode.
+
    config PCI_IMX6
    	bool
 
drivers/pci/controller/dwc/Makefile +1 -0
index 67ba59c02038..7c5a5186ea83 100644
@@ -6,6 +6,7 @@ obj-$(CONFIG_PCIE_DW_EP) += pcie-designware-ep.o
    obj-$(CONFIG_PCIE_DW_PLAT) += pcie-designware-plat.o
    obj-$(CONFIG_PCIE_AMD_MDB) += pcie-amd-mdb.o
    obj-$(CONFIG_PCIE_BT1) += pcie-bt1.o
+obj-$(CONFIG_PCIE_EIC7700) += pcie-eic7700.o
    obj-$(CONFIG_PCI_DRA7XX) += pci-dra7xx.o
    obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
    obj-$(CONFIG_PCIE_FU740) += pcie-fu740.o
drivers/pci/controller/dwc/pcie-eic7700.c new file +225 -0
new file mode 100644
index 000000000000..cb7cdea6a94b
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ESWIN EIC7700 PCIe root complex driver
+ *
+ * Copyright 2025, Beijing ESWIN Computing Technology Co., Ltd.
+ *
+ * Authors: Yu Ning <[email protected]>
+ *          Senchuan Zhang <[email protected]>
+ *          Yanghui Ou <[email protected]>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/resource.h>
+#include <linux/reset.h>
+#include <linux/types.h>
+
+#include "pcie-designware.h"
+
+/* ELBI registers */
+#define PCIEELBI_CTRL0_OFFSET		0x0
+#define PCIEELBI_STATUS0_OFFSET		0x100
+
+/* LTSSM register fields */
+#define PCIEELBI_APP_LTSSM_ENABLE	BIT(5)
+
+/* APP_HOLD_PHY_RST register fields */
+#define PCIEELBI_APP_HOLD_PHY_RST	BIT(6)
+
+/* PM_SEL_AUX_CLK register fields */
+#define PCIEELBI_PM_SEL_AUX_CLK		BIT(16)
+
+/* DEV_TYPE register fields */
+#define PCIEELBI_CTRL0_DEV_TYPE		GENMASK(3, 0)
+
+/* Vendor and device ID value */
+#define PCI_VENDOR_ID_ESWIN		0x1fe1
+#define PCI_DEVICE_ID_ESWIN		0x2030
+
+#define EIC7700_NUM_RSTS		ARRAY_SIZE(eic7700_pcie_rsts)
+
+static const char * const eic7700_pcie_rsts[] = {
+	"pwr",
+	"dbi",
+};
+
+struct eic7700_pcie_data {
+	bool no_pme_handshake;
+};
+
+struct eic7700_pcie_port {
+	struct list_head list;
+	struct reset_control *perst;
+	int num_lanes;
+};
+
+struct eic7700_pcie {
+	struct dw_pcie pci;
+	struct clk_bulk_data *clks;
+	struct reset_control_bulk_data resets[EIC7700_NUM_RSTS];
+	struct list_head ports;
+	const struct eic7700_pcie_data *data;
+	int num_clks;
+};
+
+#define to_eic7700_pcie(x) dev_get_drvdata((x)->dev)
+
+static int eic7700_pcie_start_link(struct dw_pcie *pci)
+{
+	u32 val;
+
+	/* Enable LTSSM */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val |= PCIEELBI_APP_LTSSM_ENABLE;
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	return 0;
+}
+
+static bool eic7700_pcie_link_up(struct dw_pcie *pci)
+{
+	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	u16 val = dw_pcie_readw_dbi(pci, offset + PCI_EXP_LNKSTA);
+
+	return val & PCI_EXP_LNKSTA_DLLLA;
+}
+
+static int eic7700_pcie_perst_reset(struct eic7700_pcie_port *port,
+				    struct eic7700_pcie *pcie)
+{
+	int ret;
+
+	ret = reset_control_assert(port->perst);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to assert PERST#\n");
+		return ret;
+	}
+
+	/* Ensure that PERST# has been asserted for at least 100 ms */
+	msleep(PCIE_T_PVPERL_MS);
+
+	ret = reset_control_deassert(port->perst);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to deassert PERST#\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int eic7700_pcie_parse_port(struct eic7700_pcie *pcie,
+				   struct device_node *node)
+{
+	struct device *dev = pcie->pci.dev;
+	struct eic7700_pcie_port *port;
+
+	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	port->perst = of_reset_control_get_exclusive(node, "perst");
+	if (IS_ERR(port->perst)) {
+		dev_err(dev, "Failed to get PERST# reset\n");
+		return PTR_ERR(port->perst);
+	}
+
+	/*
+	 * TODO: Since the Root Port node is separated out by pcie devicetree,
+	 * the DWC core initialization code can't parse the num-lanes attribute
+	 * in the Root Port. Before entering the DWC core initialization code,
+	 * the platform driver code parses the Root Port node. The EIC7700 only
+	 * supports one Root Port node, and the num-lanes attribute is suitable
+	 * for the case of one Root Rort.
+	 */
+	if (!of_property_read_u32(node, "num-lanes", &port->num_lanes))
+		pcie->pci.num_lanes = port->num_lanes;
+
+	INIT_LIST_HEAD(&port->list);
+	list_add_tail(&port->list, &pcie->ports);
+
+	return 0;
+}
+
+static int eic7700_pcie_parse_ports(struct eic7700_pcie *pcie)
+{
+	struct eic7700_pcie_port *port, *tmp;
+	struct device *dev = pcie->pci.dev;
+	int ret;
+
+	for_each_available_child_of_node_scoped(dev->of_node, of_port) {
+		ret = eic7700_pcie_parse_port(pcie, of_port);
+		if (ret)
+			goto err_port;
+	}
+
+	return 0;
+
+err_port:
+	list_for_each_entry_safe(port, tmp, &pcie->ports, list)
+		list_del(&port->list);
+
+	return ret;
+}
+
+static int eic7700_pcie_host_init(struct dw_pcie_rp *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct eic7700_pcie *pcie = to_eic7700_pcie(pci);
+	struct eic7700_pcie_port *port;
+	u32 val;
+	int ret;
+
+	pcie->num_clks = devm_clk_bulk_get_all_enabled(pci->dev, &pcie->clks);
+	if (pcie->num_clks < 0)
+		return dev_err_probe(pci->dev, pcie->num_clks,
+				     "Failed to get pcie clocks\n");
+
+	/*
+	 * The PWR and DBI Reset signals are respectively used to reset the
+	 * PCIe controller and the DBI registers.
+	 * The PERST# signal is a reset signal that simultaneously controls the
+	 * PCIe controller, PHY, and Endpoint.
+	 * Before configuring the PHY, the PERST# signal must first be
+	 * deasserted.
+	 * The external reference clock is supplied simultaneously to the PHY
+	 * and EP. When the PHY is configurable, the entire chip already has
+	 * stable power and reference clock.
+	 * The PHY will be ready within 20ms after writing app_hold_phy_rst
+	 * register of ELBI register space.
+	 */
+	ret = reset_control_bulk_deassert(EIC7700_NUM_RSTS, pcie->resets);
+	if (ret) {
+		dev_err(pcie->pci.dev, "Failed to deassert resets\n");
+		return ret;
+	}
+
+	/* Configure Root Port type */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val &= ~PCIEELBI_CTRL0_DEV_TYPE;
+	val |= FIELD_PREP(PCIEELBI_CTRL0_DEV_TYPE, PCI_EXP_TYPE_ROOT_PORT);
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	list_for_each_entry(port, &pcie->ports, list) {
+		ret = eic7700_pcie_perst_reset(port, pcie);
+		if (ret)
+			goto err_perst;
+	}
+
+	/* Configure app_hold_phy_rst */
+	val = readl_relaxed(pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+	val &= ~PCIEELBI_APP_HOLD_PHY_RST;
+	writel_relaxed(val, pci->elbi_base + PCIEELBI_CTRL0_OFFSET);
+
+	/* The maximum waiting time for the clock switch lock is 20ms */
+	ret = readl_poll_timeout(pci->elbi_base + PCIEELBI_STATUS0_OFFSET,
+				 val, !(val & PCIEELBI_PM_SEL_AUX_CLK), 1000,
+				 20000);
+	if (ret) {
+		dev_err(pci->dev, "Timeout waiting for PM_SEL_AUX_CLK ready\n");
+		goto err_phy_init;
Quoted 8 lines

drivers/pci/controller/dwc/pcie-eic7700.c line 231

Quoted 6 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +6 -0
+	}
+
+	/*
+	 * Configure ESWIN VID:DID for Root Port as the default values are
+	 * invalid.
+	 */

we need to make dbi registers writeable before this through this API dw_pcie_dbi_ro_wr_en().

Hi, Krishna Chaitanya

Thank you for your comment.
When our driver initialization starts, the BIT(0) of the PCIE_MISC_CONTROL_1_OFF address defaults to 1, allowing for the reading and writing of dbi registers.

Quoted 98 lines
Quoted 2 lines

Thanks for the info, then in that case do we need to clear it before enumeration?

Thank you for the reminder.
Do you mean that after executing the dw_pcie_writew_dbi function, dw_pcie_dbi_ro_wr_dis() should be called to clear the writable bits of dbi?

Kind regards,
Senchuan Zhang

Quoted 89 lines
Quoted 89 lines
Quoted 76 lines
Quoted 76 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +76 -0
+	dw_pcie_writew_dbi(pci, PCI_VENDOR_ID, PCI_VENDOR_ID_ESWIN);
+	dw_pcie_writew_dbi(pci, PCI_DEVICE_ID, PCI_DEVICE_ID_ESWIN);
+
+	return 0;
+
+err_phy_init:
+	list_for_each_entry(port, &pcie->ports, list)
+		reset_control_assert(port->perst);
+err_perst:
+	reset_control_bulk_assert(EIC7700_NUM_RSTS, pcie->resets);
+
+	return ret;
+}
+
+static void eic7700_pcie_host_deinit(struct dw_pcie_rp *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct eic7700_pcie *pcie = to_eic7700_pcie(pci);
+	struct eic7700_pcie_port *port;
+
+	list_for_each_entry(port, &pcie->ports, list)
+		reset_control_assert(port->perst);
+	reset_control_bulk_assert(EIC7700_NUM_RSTS, pcie->resets);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
+}
+
+static const struct dw_pcie_host_ops eic7700_pcie_host_ops = {
+	.init = eic7700_pcie_host_init,
+	.deinit = eic7700_pcie_host_deinit,
+};
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+	.start_link = eic7700_pcie_start_link,
+	.link_up = eic7700_pcie_link_up,
+};
+
+static int eic7700_pcie_probe(struct platform_device *pdev)
+{
+	const struct eic7700_pcie_data *data;
+	struct eic7700_pcie_port *port, *tmp;
+	struct device *dev = &pdev->dev;
+	struct eic7700_pcie *pcie;
+	struct dw_pcie *pci;
+	int ret, i;
+
+	data = of_device_get_match_data(dev);
+	if (!data)
+		return dev_err_probe(dev, -ENODATA, "OF data missing\n");
+
+	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
+	if (!pcie)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&pcie->ports);
+
+	pci = &pcie->pci;
+	pci->dev = dev;
+	pci->ops = &dw_pcie_ops;
+	pci->pp.ops = &eic7700_pcie_host_ops;
+	pcie->data = data;
+	pci->no_pme_handshake = pcie->data->no_pme_handshake;
+
+	for (i = 0; i < EIC7700_NUM_RSTS; i++)
+		pcie->resets[i].id = eic7700_pcie_rsts[i];
+
+	ret = devm_reset_control_bulk_get_exclusive(dev, EIC7700_NUM_RSTS,
+						    pcie->resets);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to get resets\n");
+
+	ret = eic7700_pcie_parse_ports(pcie);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Failed to parse Root Port: %d\n", ret);
+
+	platform_set_drvdata(pdev, pcie);
Quoted 8 lines

drivers/pci/controller/dwc/pcie-eic7700.c line 313

Quoted 6 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +6 -0
+
+	pm_runtime_no_callbacks(dev);
+	devm_pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0)
+		goto err_pm_runtime_put;

Any specific reason why we are enabling runtime pm and doing pm_runtime_get_sync()

To avoid warnings when the driver starts, pm_runtime_get_sync() has been added. Warnings as follows:

"pci0000:00: runtime PM trying to activate child device pci0000:00 but parent (54000000.pcie) is not active".

Yes, otherwise we are violating the PCIe spec.

- Krishna Chaitanya.

Quoted 69 lines
Quoted 69 lines
Quoted 69 lines

Kind regards,
Senchuan Zhang

Quoted 65 lines
Quoted 65 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +65 -0
+
+	ret = dw_pcie_host_init(&pci->pp);
+	if (ret) {
+		dev_err(dev, "Failed to initialize host\n");
+		goto err_init;
+	}
+
+	return 0;
+
+err_init:
+	list_for_each_entry_safe(port, tmp, &pcie->ports, list) {
+		list_del(&port->list);
+		reset_control_put(port->perst);
+	}
+err_pm_runtime_put:
+	pm_runtime_put(dev);
+
+	return ret;
+}
+
+static int eic7700_pcie_suspend_noirq(struct device *dev)
+{
+	struct eic7700_pcie *pcie = dev_get_drvdata(dev);
+
+	return dw_pcie_suspend_noirq(&pcie->pci);
+}
+
+static int eic7700_pcie_resume_noirq(struct device *dev)
+{
+	struct eic7700_pcie *pcie = dev_get_drvdata(dev);
+
+	return dw_pcie_resume_noirq(&pcie->pci);
+}
+
+static const struct dev_pm_ops eic7700_pcie_pm_ops = {
+	NOIRQ_SYSTEM_SLEEP_PM_OPS(eic7700_pcie_suspend_noirq,
+				  eic7700_pcie_resume_noirq)
+};
+
+static const struct eic7700_pcie_data eic7700_data = {
+	.no_pme_handshake = true,
+};
+
+static const struct of_device_id eic7700_pcie_of_match[] = {
+	{ .compatible = "eswin,eic7700-pcie", .data = &eic7700_data },
+	{},
+};
+
+static struct platform_driver eic7700_pcie_driver = {
+	.probe = eic7700_pcie_probe,
+	.driver = {
+		.name = "eic7700-pcie",
+		.of_match_table = eic7700_pcie_of_match,
+		.suppress_bind_attrs = true,
+		.pm = &eic7700_pcie_pm_ops,
+		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
+	},
+};
+builtin_platform_driver(eic7700_pcie_driver);
+
+MODULE_DESCRIPTION("Eswin EIC7700 PCIe host controller driver");
+MODULE_AUTHOR("Yu Ning <[email protected]>");
+MODULE_AUTHOR("Senchuan Zhang <[email protected]>");
+MODULE_AUTHOR("Yanghui Ou <[email protected]>");
+MODULE_LICENSE("GPL");
#8 lore raw

Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

In reply to [email protected]
Quoted 11 lines · On Tue, Dec 02, 2025 at 05:04:06PM +0800, [email protected]…

From: Senchuan Zhang <[email protected]>

Add driver for the Eswin EIC7700 PCIe host controller, which is based on the DesignWare PCIe core, IP revision 5.96a. The PCIe Gen.3 controller supports a data rate of 8 GT/s and 4 channels, support INTx and MSI interrupts.

drivers/pci/controller/dwc/pcie-eic7700.c new file +3 -0
+static int eic7700_pcie_host_init(struct dw_pcie_rp *pp)
...
+	/*
+	 * The PWR and DBI Reset signals are respectively used to reset the

drivers/pci/controller/dwc/pcie-eic7700.c line 194

Quoted 10 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +10 -0
+	 * PCIe controller and the DBI registers.
+	 * The PERST# signal is a reset signal that simultaneously controls the
+	 * PCIe controller, PHY, and Endpoint.
+	 * Before configuring the PHY, the PERST# signal must first be
+	 * deasserted.
+	 * The external reference clock is supplied simultaneously to the PHY
+	 * and EP. When the PHY is configurable, the entire chip already has
+	 * stable power and reference clock.
+	 * The PHY will be ready within 20ms after writing app_hold_phy_rst
+	 * register of ELBI register space.

Add blank lines between paragraphs.

drivers/pci/controller/dwc/pcie-eic7700.c line 292

Quoted 3 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +2 -0
+static int eic7700_pcie_probe(struct platform_device *pdev)
...
+	pci->no_pme_handshake = pcie->data->no_pme_handshake;

This needs to go in the 3/3 "PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast" patch because "no_pme_handshake" doesn't exist yet so this patch doesn't build by itself.

drivers/pci/controller/dwc/pcie-eic7700.c line 351

Quoted 4 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +4 -0
+static const struct dev_pm_ops eic7700_pcie_pm_ops = {
+	NOIRQ_SYSTEM_SLEEP_PM_OPS(eic7700_pcie_suspend_noirq,
+				  eic7700_pcie_resume_noirq)
+};

Use DEFINE_NOIRQ_DEV_PM_OPS() instead. The collection of PM-related macros is confusing to say the least, and they're not used consistently across the PCIe drivers, but I *think* the rule of thumb should be:

Prefer DEFINE_NOIRQ_DEV_PM_OPS() over NOIRQ_SYSTEM_SLEEP_PM_OPS() when possible and omit pm_sleep_ptr() and pm_ptr().

Bjorn

#9 lore raw

Re: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 35 lines

-----Original Messages-----
From: "Bjorn Helgaas" <[email protected]>
Send time:Thursday, 11/12/2025 00:43:27
To: [email protected]
Cc: [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected]
Subject: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 11 lines · On Tue, Dec 02, 2025 at 05:04:06PM +0800, [email protected]…

From: Senchuan Zhang <[email protected]>

Add driver for the Eswin EIC7700 PCIe host controller, which is based on the DesignWare PCIe core, IP revision 5.96a. The PCIe Gen.3 controller supports a data rate of 8 GT/s and 4 channels, support INTx and MSI interrupts.

drivers/pci/controller/dwc/pcie-eic7700.c new file +3 -0
+static int eic7700_pcie_host_init(struct dw_pcie_rp *pp)
...
+	/*
+	 * The PWR and DBI Reset signals are respectively used to reset the

drivers/pci/controller/dwc/pcie-eic7700.c line 194

Quoted 10 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +10 -0
+	 * PCIe controller and the DBI registers.
+	 * The PERST# signal is a reset signal that simultaneously controls the
+	 * PCIe controller, PHY, and Endpoint.
+	 * Before configuring the PHY, the PERST# signal must first be
+	 * deasserted.
+	 * The external reference clock is supplied simultaneously to the PHY
+	 * and EP. When the PHY is configurable, the entire chip already has
+	 * stable power and reference clock.
+	 * The PHY will be ready within 20ms after writing app_hold_phy_rst
+	 * register of ELBI register space.

Add blank lines between paragraphs.

Quoted 7 lines

drivers/pci/controller/dwc/pcie-eic7700.c line 292

Quoted 3 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +2 -0
+static int eic7700_pcie_probe(struct platform_device *pdev)
...
+	pci->no_pme_handshake = pcie->data->no_pme_handshake;

This needs to go in the 3/3 "PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast" patch because "no_pme_handshake" doesn't exist yet so this patch doesn't build by itself.

Hi, Bjorn

Thanks for your comment.
Do I need to adjust the order of the patches?
3/2 "PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast" 3/3 "PCI: eic7700: Add Eswin PCIe host controller driver"

Or merge Patch 2/3 and Patch 3/3?

Kind regards,
Senchuan Zhang

Quoted 11 lines

drivers/pci/controller/dwc/pcie-eic7700.c line 351

Quoted 5 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +4 -0
+static const struct dev_pm_ops eic7700_pcie_pm_ops = {
+	NOIRQ_SYSTEM_SLEEP_PM_OPS(eic7700_pcie_suspend_noirq,
+				  eic7700_pcie_resume_noirq)
+};

Use DEFINE_NOIRQ_DEV_PM_OPS() instead. The collection of PM-related macros is confusing to say the least, and they're not used consistently across the PCIe drivers, but I *think* the rule of thumb should be:

Quoted 2 lines

Prefer DEFINE_NOIRQ_DEV_PM_OPS() over NOIRQ_SYSTEM_SLEEP_PM_OPS() when possible and omit pm_sleep_ptr() and pm_ptr().

Okey, thanks.
I will use the following combination: DEFINE_NOIRQ_DEV_PM_OPS(eic7700_pcie_pm, eic7700_pcie_suspend_noirq,

                        eic7700_pcie_resume_noirq);

.pm = &eic7700_pcie_pm,

#10 lore raw

Re: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 6 lines · zhangsenchuan
Quoted 6 lines

-----Original Messages-----
From: "Bjorn Helgaas" <[email protected]>
Send time:Thursday, 11/12/2025 00:43:27
To: [email protected]
Cc: [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected]
Subject: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Please avoid the pointless quote of all the headers (above) if you can. That just clutters the thread. Also trim context that is not relevant. More hints here: https://subspace.kernel.org/etiquette.html

Quoted 16 lines
Quoted 8 lines · On Tue, Dec 02, 2025 at 05:04:06PM +0800, [email protected]…
Quoted 6 lines

From: Senchuan Zhang <[email protected]>

Add driver for the Eswin EIC7700 PCIe host controller, which is based on the DesignWare PCIe core, IP revision 5.96a. The PCIe Gen.3 controller supports a data rate of 8 GT/s and 4 channels, support INTx and MSI interrupts.

Quoted 7 lines

drivers/pci/controller/dwc/pcie-eic7700.c line 292

Quoted 3 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +2 -0
+static int eic7700_pcie_probe(struct platform_device *pdev)
...
+	pci->no_pme_handshake = pcie->data->no_pme_handshake;

This needs to go in the 3/3 "PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast" patch because "no_pme_handshake" doesn't exist yet so this patch doesn't build by itself.

Quoted 5 lines

Do I need to adjust the order of the patches?
3/2 "PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast" 3/3 "PCI: eic7700: Add Eswin PCIe host controller driver"

Or merge Patch 2/3 and Patch 3/3?

I think the best thing would be to leave dw_pcie_suspend_noirq() along and implement eic7700_pcie_suspend_noirq() without calling it.

dw_pcie_suspend_noirq() is already problematic [1], and we don't need more complication there. Even without calling dw_pcie_suspend_noirq(), your eic7700_pcie_suspend_noirq() will be pretty simple. Just add a comment about why you don't use dw_pcie_suspend_noirq().

[1] https://lore.kernel.org/linux-pci/20251114213540.GA2335845@bhelgaas/

#11 lore raw

Re: Re: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Quoted 5 lines
Quoted 1 line
Quoted 1 line

Subject: Re: [PATCH v7 2/3] PCI: eic7700: Add Eswin PCIe host controller driver

Please avoid the pointless quote of all the headers (above) if you can. That just clutters the thread. Also trim context that is not relevant. More hints here: https://subspace.kernel.org/etiquette.html

Okey, thanks.

Quoted 26 lines
Quoted 17 lines
Quoted 9 lines · On Tue, Dec 02, 2025 at 05:04:06PM +0800, [email protected]…
Quoted 6 lines

From: Senchuan Zhang <[email protected]>

Add driver for the Eswin EIC7700 PCIe host controller, which is based on the DesignWare PCIe core, IP revision 5.96a. The PCIe Gen.3 controller supports a data rate of 8 GT/s and 4 channels, support INTx and MSI interrupts.

Quoted 7 lines

drivers/pci/controller/dwc/pcie-eic7700.c line 292

Quoted 3 lines
drivers/pci/controller/dwc/pcie-eic7700.c new file +2 -0
+static int eic7700_pcie_probe(struct platform_device *pdev)
...
+	pci->no_pme_handshake = pcie->data->no_pme_handshake;

This needs to go in the 3/3 "PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast" patch because "no_pme_handshake" doesn't exist yet so this patch doesn't build by itself.

Quoted 5 lines

Do I need to adjust the order of the patches?
3/2 "PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast" 3/3 "PCI: eic7700: Add Eswin PCIe host controller driver"

Or merge Patch 2/3 and Patch 3/3?

I think the best thing would be to leave dw_pcie_suspend_noirq() along and implement eic7700_pcie_suspend_noirq() without calling it.

Quoted 7 lines

dw_pcie_suspend_noirq() is already problematic [1], and we don't need more complication there. Even without calling dw_pcie_suspend_noirq(), your eic7700_pcie_suspend_noirq() will be pretty simple. Just add a comment about why you don't use dw_pcie_suspend_noirq().

[1] https://lore.kernel.org/linux-pci/20251114213540.GA2335845@bhelgaas/

Thanks for your suggestion. I have sent the V8 patch, and remove dw_pcie_suspend_noirq/dw_pcie_resume_noirq in the driver file.

Kind regards,
Senchuan Zhang

#12 lore raw

PATCH v7 3/3 PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast

In reply to [email protected]

From: Senchuan Zhang <[email protected]>

The ESWIN EIC7700 SoC lacks hardware support for the L2/L3 low-power link states. It cannot enter the L2/L3 ready state through the PME_Turn_Off/PME_To_Ack handshake protocol. To address this, add a no_pme_handshake flag skip PME_Turn_Off broadcast and link state check code, other driver can reuse this flag if meet the similar situation.

---
 drivers/pci/controller/dwc/pcie-designware-host.c | 4 ++++
 drivers/pci/controller/dwc/pcie-designware.h      | 1 +
 2 files changed, 5 insertions(+)
drivers/pci/controller/dwc/pcie-designware-host.c +4 -0
index 372207c33a85..8302bc7a6cbf 100644
@@ -1168,6 +1168,9 @@ int dw_pcie_suspend_noirq(struct dw_pcie *pci)
 	if (dw_pcie_readw_dbi(pci, offset + PCI_EXP_LNKCTL) & PCI_EXP_LNKCTL_ASPM_L1)
 		return 0;
 
+	if (pci->no_pme_handshake)
+		goto stop_link;
+
 	if (pci->pp.ops->pme_turn_off) {
 		pci->pp.ops->pme_turn_off(&pci->pp);
 	} else {
@@ -1194,6 +1197,7 @@ int dw_pcie_suspend_noirq(struct dw_pcie *pci)
 	 */
 	udelay(1);
 
+stop_link:
 	dw_pcie_stop_link(pci);
 	if (pci->pp.ops->deinit)
 		pci->pp.ops->deinit(&pci->pp);
drivers/pci/controller/dwc/pcie-designware.h +1 -0
index 31685951a080..e8057db303d0 100644
@@ -549,6 +549,7 @@ struct dw_pcie {
 	 * use_parent_dt_ranges to true to avoid this warning.
 	 */
 	bool			use_parent_dt_ranges;
+	bool			no_pme_handshake;
 };
 
 #define to_dw_pcie_from_pp(port) container_of((port), struct dw_pcie, pp)

--
2.25.1

#13 lore raw

Re: [PATCH v7 3/3] PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast

Hello,

Quoted 7 lines · On 12/2/25 10:04, [email protected] wrote:

From: Senchuan Zhang <[email protected]>

The ESWIN EIC7700 SoC lacks hardware support for the L2/L3 low-power link states. It cannot enter the L2/L3 ready state through the PME_Turn_Off/PME_To_Ack handshake protocol. To address this, add a no_pme_handshake flag skip PME_Turn_Off broadcast and link state check code, other driver can reuse this flag if meet the similar situation.

What about testing !PME_SUPPORT in the PM Capabilities Register, or just re-use the struct pci_dev pme_support flag ?

Regards,

Quoted 46 lines
---
  drivers/pci/controller/dwc/pcie-designware-host.c | 4 ++++
  drivers/pci/controller/dwc/pcie-designware.h      | 1 +
  2 files changed, 5 insertions(+)
drivers/pci/controller/dwc/pcie-designware-host.c +4 -0
index 372207c33a85..8302bc7a6cbf 100644
@@ -1168,6 +1168,9 @@ int dw_pcie_suspend_noirq(struct dw_pcie *pci)
  	if (dw_pcie_readw_dbi(pci, offset + PCI_EXP_LNKCTL) & PCI_EXP_LNKCTL_ASPM_L1)
  		return 0;
 
+	if (pci->no_pme_handshake)
+		goto stop_link;
+
  	if (pci->pp.ops->pme_turn_off) {
  		pci->pp.ops->pme_turn_off(&pci->pp);
  	} else {
@@ -1194,6 +1197,7 @@ int dw_pcie_suspend_noirq(struct dw_pcie *pci)
  	 */
  	udelay(1);
 
+stop_link:
  	dw_pcie_stop_link(pci);
  	if (pci->pp.ops->deinit)
  		pci->pp.ops->deinit(&pci->pp);
drivers/pci/controller/dwc/pcie-designware.h +1 -1
index 31685951a080..e8057db303d0 100644
@@ -549,6 +549,7 @@ struct dw_pcie {
  	 * use_parent_dt_ranges to true to avoid this warning.
  	 */
  	bool			use_parent_dt_ranges;
+	bool			no_pme_handshake;
  };
 
  #define to_dw_pcie_from_pp(port) container_of((port), struct dw_pcie, pp)
--

2.25.1

#14 lore raw

Re: Re: [PATCH v7 3/3] PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast

Quoted 15 lines

-----Original Messages-----
From: "Christian Bruel" <[email protected]>
Send time:Wednesday, 03/12/2025 18:09:06
To: [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], [email protected]
Cc: [email protected], [email protected], [email protected], [email protected]
Subject: Re: [PATCH v7 3/3] PCI: dwc: Add no_pme_handshake flag and skip PME_Turn_Off broadcast

Hello,

Quoted 2 lines · On 12/2/25 10:04, [email protected] wrote:

From: Senchuan Zhang <[email protected]>

Quoted 9 lines
Quoted 5 lines

The ESWIN EIC7700 SoC lacks hardware support for the L2/L3 low-power link states. It cannot enter the L2/L3 ready state through the PME_Turn_Off/PME_To_Ack handshake protocol. To address this, add a no_pme_handshake flag skip PME_Turn_Off broadcast and link state check code, other driver can reuse this flag if meet the similar situation.

What about testing !PME_SUPPORT in the PM Capabilities Register, or just re-use the struct pci_dev pme_support flag ?

Hi, Christian

Thank you for your suggestions.
Our hardware supports generating PME#, supports L0s/L1/L1.1 low-power mode, but L2/L3 low-power link state is not supported. It cannot enter the L2/L3 ready state through the PME_Turn_Off/PME_To_Ack handshake protocol.

Through the PM Capabilities Register, it can be seen that PME# is supported. The pme_support flag is about whether PME# generation is supported, which is not very suitable for us.

Kind regards,
Senchuan Zhang

Quoted 47 lines
Quoted 47 lines
---
  drivers/pci/controller/dwc/pcie-designware-host.c | 4 ++++
  drivers/pci/controller/dwc/pcie-designware.h      | 1 +
  2 files changed, 5 insertions(+)
drivers/pci/controller/dwc/pcie-designware-host.c +4 -0
index 372207c33a85..8302bc7a6cbf 100644
@@ -1168,6 +1168,9 @@ int dw_pcie_suspend_noirq(struct dw_pcie *pci)
  	if (dw_pcie_readw_dbi(pci, offset + PCI_EXP_LNKCTL) & PCI_EXP_LNKCTL_ASPM_L1)
  		return 0;
 
+	if (pci->no_pme_handshake)
+		goto stop_link;
+
  	if (pci->pp.ops->pme_turn_off) {
  		pci->pp.ops->pme_turn_off(&pci->pp);
  	} else {
@@ -1194,6 +1197,7 @@ int dw_pcie_suspend_noirq(struct dw_pcie *pci)
  	 */
  	udelay(1);
 
+stop_link:
  	dw_pcie_stop_link(pci);
  	if (pci->pp.ops->deinit)
  		pci->pp.ops->deinit(&pci->pp);
drivers/pci/controller/dwc/pcie-designware.h +1 -1
index 31685951a080..e8057db303d0 100644
@@ -549,6 +549,7 @@ struct dw_pcie {
  	 * use_parent_dt_ranges to true to avoid this warning.
  	 */
  	bool			use_parent_dt_ranges;
+	bool			no_pme_handshake;
  };
 
  #define to_dw_pcie_from_pp(port) container_of((port), struct dw_pcie, pp)
--

2.25.1