ASoC: SOF: Support for on-demand DSP boot
Subsystems (3)
Peter Ujfalusi
maintainercover ASoC: SOF: Support for on-demand DSP boot
Hi,
On system suspend / resume we always power up the DSP and boot the firmware, which is not strictly needed as right after the firmware booted up we power the DSP down again on suspend and we also power it down after resume after some inactivity.
Similarly, on jack insert/removal we needlesly boot up the firmware to check the jack status, which needs no DSP/firmware communication.
The on-demand DSP boot will make sure that we boot the DSP firmware up only when it is needed - for audio activity, in other cases the firmware will be not booted up, which saves time.
Out of caution, add a new platform descriptor flag to enable on-demand DSP boot since this might not work without changes to platform code on certain platforms.
With the on-demand dsp boot enabled we will not boot the DSP and firmware up on system or rpm resume, just enable audio subsystem since audio IPs, like HDA and SoundWire might be needed (codecs suspend/resume operation). Only boot up the DSP during the first hw_params() call when the DSP is really going to be needed.
In this way we can handle the audio related use cases:
normal audio use (rpm suspend/resume)
system suspend/resume without active audio
system suspend/resume with active audio
system suspend/resume without active audio, and audio start before the rpm suspend timeout
Add module option to force the on-demand DSP boot to allow it to be disabled or enabled without kernel change for testing.
The on-demand boot has been tested in our CI for more than half a year and so far no issues have been seen on supported platforms since it's introduction to our development tree (sof-dev).
Regards,
Peter
---
Peter Ujfalusi (8):
ASoC: SOF: ipc4-loader: Remove redundant rpm resume_and_get from
load_library
ASoC: SOF: control: skip rpm calls in ext_volatile_get if not
implemented
ASoC: SOF: Add support for on-demand DSP boot
ASoC: SOF: sof-client: Add support for on-demand DSP boot
ASoC: SOF: Intel: hda-sdw-bpt: Add support for on-demand DSP boot
ASoC: SOF: Intel: pci-lnl: Set on_demand_dsp_boot for LNL
ASoC: SOF: Intel: pci-ptl: Set on_demand_dsp_boot for PTL and WCL
ASoC: SOF: Intel: pci-nvl: Set on_demand_dsp_boot for NVL-S
include/sound/sof.h | 3 + sound/soc/sof/compress.c | 8 + sound/soc/sof/control.c | 13 +- sound/soc/sof/core.c | 1 + sound/soc/sof/debug.c | 7 +- sound/soc/sof/intel/hda-sdw-bpt.c | 11 ++ sound/soc/sof/intel/pci-lnl.c | 1 + sound/soc/sof/intel/pci-nvl.c | 1 + sound/soc/sof/intel/pci-ptl.c | 2 + sound/soc/sof/ipc3-dtrace.c | 7 +- sound/soc/sof/ipc4-loader.c | 19 +-- sound/soc/sof/ipc4.c | 13 ++ sound/soc/sof/pcm.c | 10 ++ sound/soc/sof/pm.c | 149 +++++++++++------- sound/soc/sof/sof-client-ipc-flood-test.c | 7 +- .../soc/sof/sof-client-ipc-kernel-injector.c | 4 +- sound/soc/sof/sof-client-ipc-msg-injector.c | 14 +- sound/soc/sof/sof-client-probes.c | 26 ++- sound/soc/sof/sof-client.c | 6 + sound/soc/sof/sof-client.h | 3 + sound/soc/sof/sof-priv.h | 3 + 21 files changed, 215 insertions(+), 93 deletions(-)
Signature · 1 line
2.52.0
Peter Ujfalusi
maintainerPATCH 1/8 ASoC: SOF: ipc4-loader: Remove redundant rpm resume_and_get from load_library
The initial library loading is happening during topology loading, which is already protected with pm_runtime_resume_and_get() via pcm.c
The redundant rpm code can be dropped from sof_ipc4_load_library()
--- sound/soc/sof/ipc4-loader.c | 19 +------------------ 1 file changed, 1 insertion(+), 18 deletions(-)
sound/soc/sof/ipc4-loader.c +1 -18
@@ -175,7 +175,7 @@ static int sof_ipc4_load_library(struct snd_sof_dev *sdev, unsigned long lib_id,struct sof_ipc4_fw_data *ipc4_data = sdev->private;struct sof_ipc4_fw_library *fw_lib;ssize_t payload_offset; -int ret, i, err; +int ret, i;if (!ipc4_data->load_library) {dev_err (sdev->dev,"Library loading is not supported on this platform\n" );
@@ -223,24 +223,7 @@ static int sof_ipc4_load_library(struct snd_sof_dev *sdev, unsigned long lib_id,for (i =0 ; i < fw_lib->num_modules; i++) fw_lib->modules[i].man4_module_entry.id |= (lib_id <<SOF_IPC4_MOD_LIB_ID_SHIFT ); -/* -* Make sure that the DSP is booted and stays up while attempting the -* loading the library for the first time -*/ - ret =pm_runtime_resume_and_get (sdev->dev); -if (ret <0 && ret != -EACCES ) { -dev_err_ratelimited (sdev->dev,"%s: pm_runtime resume failed: %d\n" , - __func__, ret); - goto release; - } - ret = ipc4_data->load_library (sdev, fw_lib, false); - - err =pm_runtime_put_autosuspend (sdev->dev); -if (err <0 ) -dev_err_ratelimited (sdev->dev,"%s: pm_runtime idle failed: %d\n" , - __func__, err); -if (ret) goto release;
Signature · 1 line
2.52.0
Peter Ujfalusi
maintainerPATCH 2/8 ASoC: SOF: control: skip rpm calls in ext_volatile_get if not implemented
In reply to Peter UjfalusiTest earlier for the existence of ext_volatile_get callback and if it is missing, skip the rpm calls to avoid needles DSP power on.
No change in functionality, we just skip the DSP power on in the unlikely case when the ext_volatile _get is not supported and yet the topology adds such control.
--- sound/soc/sof/control.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
sound/soc/sof/control.c +6 -2
@@ -187,14 +187,18 @@ int snd_sof_bytes_ext_volatile_get(struct snd_kcontrol *kcontrol, unsigned int _const struct sof_ipc_tplg_ops *tplg_ops =sof_ipc_get_ops (sdev, tplg);int ret, err; +/* ignore the ext_volatile_get call if the callbacks are not provided */ +if (!tplg_ops || !tplg_ops->control || + !tplg_ops->control->bytes_ext_volatile_get) +return 0 ; + ret =pm_runtime_resume_and_get (scomp->dev);if (ret <0 && ret != -EACCES ) {dev_err_ratelimited (scomp->dev,"%s: failed to resume %d\n" , __func__, ret);return ret; } -if (tplg_ops && tplg_ops->control && tplg_ops->control->bytes_ext_volatile_get) - ret = tplg_ops->control->bytes_ext_volatile_get (scontrol, binary_data, size); + ret = tplg_ops->control->bytes_ext_volatile_get (scontrol, binary_data, size); err =pm_runtime_put_autosuspend (scomp->dev);if (err <0 )
Signature · 1 line
2.52.0
Peter Ujfalusi
maintainerPATCH 3/8 ASoC: SOF: Add support for on-demand DSP boot
In reply to Peter UjfalusiOn system suspend / resume we always power up the DSP and boot the firmware, which is not strictly needed as right after the firmware booted up we power the DSP down again on suspend and we also power it down after resume after some inactivity.
Out of caution, add a new platform descriptor flag to enable on-demand DSP boot since this might not work without changes to platform code on certain platforms.
With the on-demand dsp boot enabled we will not boot the DSP and firmware up on system or rpm resume, just enable audio subsystem since audio IPs, like HDA and SoundWire might be needed (codecs suspend/resume operation). Only boot up the DSP during the first hw_params() call when the DSP is really going to be needed.
In this way we can handle the audio related use cases:
normal audio use (rpm suspend/resume)
system suspend/resume without active audio
system suspend/resume with active audio
system suspend/resume without active audio, and audio start before the rpm suspend timeout
Add module option to force the on-demand DSP boot to allow it to be disabled or enabled without kernel change for testing.
--- include/sound/sof.h | 3 + sound/soc/sof/compress.c | 8 ++ sound/soc/sof/control.c | 7 +- sound/soc/sof/core.c | 1 + sound/soc/sof/debug.c | 7 +- sound/soc/sof/ipc3-dtrace.c | 7 +- sound/soc/sof/ipc4.c | 13 ++++ sound/soc/sof/pcm.c | 10 +++ sound/soc/sof/pm.c | 149 ++++++++++++++++++++++-------------- sound/soc/sof/sof-priv.h | 3 + 10 files changed, 149 insertions(+), 59 deletions(-)
include/sound/sof.h +3 -0
@@ -159,6 +159,9 @@ struct sof_dev_desc {/* The platform supports DSPless mode */ bool dspless_mode_supported; +/* On demand DSP booting is possible on the platform */ +bool on_demand_dsp_boot; +/* defaults paths for firmware, library and topology files */ const char *default_fw_path[SOF_IPC_TYPE_COUNT ];const char *default_lib_path[SOF_IPC_TYPE_COUNT ];
sound/soc/sof/compress.c +8 -0
@@ -195,6 +195,14 @@ static int sof_compr_set_params(struct snd_soc_component *component,if (sizeof (*pcm) + ext_data_size > sdev->ipc->max_payload_size)return -EINVAL ; +/* +* Make sure that the DSP is booted up, which might not be the +* case if the on-demand DSP boot is used +*/ + ret =snd_sof_boot_dsp_firmware (sdev); +if (ret) +return ret; + pcm =kzalloc (sizeof (*pcm) + ext_data_size,GFP_KERNEL );if (!pcm)return -ENOMEM ;
sound/soc/sof/control.c +6 -1
@@ -198,7 +198,12 @@ int snd_sof_bytes_ext_volatile_get(struct snd_kcontrol *kcontrol, unsigned int _return ret; } - ret = tplg_ops->control->bytes_ext_volatile_get (scontrol, binary_data, size); +/* Make sure the DSP/firmware is booted up */ + ret =snd_sof_boot_dsp_firmware (sdev); +if (!ret) + ret = tplg_ops->control->bytes_ext_volatile_get (scontrol, + binary_data, + size); err =pm_runtime_put_autosuspend (scomp->dev);if (err <0 )
sound/soc/sof/core.c +1 -0
@@ -680,6 +680,7 @@ int snd_sof_device_probe(struct device *dev, struct snd_sof_pdata *plat_data)mutex_init (&sdev->power_state_access);mutex_init (&sdev->ipc_client_mutex);mutex_init (&sdev->client_event_handler_mutex); +mutex_init (&sdev->dsp_fw_boot_mutex);/* set default timeouts if none provided */ if (plat_data->desc->ipc_timeout ==0 )
sound/soc/sof/debug.c +6 -1
@@ -216,7 +216,12 @@ static int memory_info_update(struct snd_sof_dev *sdev, char *buf, size_t buff_s goto error; } - ret =sof_ipc_tx_message (sdev->ipc, &msg, msg.size, reply,SOF_IPC_MSG_MAX_SIZE ); +/* Make sure the DSP/firmware is booted up */ + ret =snd_sof_boot_dsp_firmware (sdev); +if (!ret) + ret =sof_ipc_tx_message (sdev->ipc, &msg, msg.size, reply, +SOF_IPC_MSG_MAX_SIZE ); +pm_runtime_put_autosuspend (sdev->dev);if (ret <0 || reply->rhdr.error <0 ) { ret =min (ret, reply->rhdr.error);
sound/soc/sof/ipc3-dtrace.c +6 -1
@@ -171,7 +171,12 @@ static int ipc3_trace_update_filter(struct snd_sof_dev *sdev, int num_elems,dev_err (sdev->dev,"enabling device failed: %d\n" , ret); goto error; } - ret =sof_ipc_tx_message_no_reply (sdev->ipc, msg, msg->hdr.size); + +/* Make sure the DSP/firmware is booted up */ + ret =snd_sof_boot_dsp_firmware (sdev); +if (!ret) + ret =sof_ipc_tx_message_no_reply (sdev->ipc, msg, msg->hdr.size); +pm_runtime_put_autosuspend (sdev->dev); error:
sound/soc/sof/ipc4.c +13 -0
@@ -892,6 +892,19 @@ void sof_ipc4_mic_privacy_state_change(struct snd_sof_dev *sdev, bool state)struct sof_ipc4_msg msg;u32 data = state; +/* +* The mic privacy change notification's role is to notify the running +* firmware that there is a change in mic privacy state from whatever +* the state was before - since the firmware booted up or since the +* previous change during runtime. +* +* If the firmware has not been booted up, there is no need to send +* change notification (the firmware is not booted up). +* The firmware checks the current state during its boot. +*/ +if (sdev->fw_state !=SOF_FW_BOOT_COMPLETE ) +return ; + msg.primary =SOF_IPC4_MSG_TARGET (SOF_IPC4_MODULE_MSG ); msg.primary |=SOF_IPC4_MSG_DIR (SOF_IPC4_MSG_REQUEST ); msg.primary |=SOF_IPC4_MOD_ID (SOF_IPC4_MOD_INIT_BASEFW_MOD_ID );
sound/soc/sof/pcm.c +10 -0
@@ -122,6 +122,16 @@ static int sof_pcm_hw_params(struct snd_soc_component *component,spcm_dbg (spcm, substream->stream,"Entry: hw_params\n" ); +if (!sdev->dspless_mode_selected) { +/* +* Make sure that the DSP is booted up, which might not be the +* case if the on-demand DSP boot is used +*/ + ret =snd_sof_boot_dsp_firmware (sdev); +if (ret) +return ret; + } +/* * Handle repeated calls to hw_params() without free_pcm() in * between. At least ALSA OSS emulation depends on this.
sound/soc/sof/pm.c +93 -56
216 lines not on this page · raw message
sound/soc/sof/sof-priv.h +3 -0
@@ -580,6 +580,8 @@ struct snd_sof_dev {wait_queue_head_t boot_wait;enum sof_fw_state fw_state;bool first_boot; +/* mutex to protect DSP firmware boot (except initial, probe time boot */ +struct mutex dsp_fw_boot_mutex;/* work queue in case the probe is implemented in two steps */ struct work_struct probe_work;
@@ -703,6 +705,7 @@ int snd_sof_suspend(struct device *dev);int snd_sof_dsp_power_down_notify (struct snd_sof_dev *sdev);int snd_sof_prepare (struct device *dev);void snd_sof_complete (struct device *dev); +int snd_sof_boot_dsp_firmware (struct snd_sof_dev *sdev);void snd_sof_new_platform_drv (struct snd_sof_dev *sdev);
Signature · 1 line
2.52.0
Peter Ujfalusi
maintainerPATCH 4/8 ASoC: SOF: sof-client: Add support for on-demand DSP boot
In reply to Peter UjfalusiWith the introduction of on-demand DSP boot the rpm status not necessary tells that the DSP firmware is booted up.
Introduce the sof_client_boot_dsp() which can be used to make sure that the DSP is booted and it can handle IPCs.
Update the client drivers to use the new function where it is expected that the DSP is booted up.
--- sound/soc/sof/sof-client-ipc-flood-test.c | 7 ++--- .../soc/sof/sof-client-ipc-kernel-injector.c | 4 ++- sound/soc/sof/sof-client-ipc-msg-injector.c | 14 ++++++---- sound/soc/sof/sof-client-probes.c | 26 ++++++++++++++----- sound/soc/sof/sof-client.c | 6 +++++ sound/soc/sof/sof-client.h | 3 +++ 6 files changed, 45 insertions(+), 15 deletions(-)
sound/soc/sof/sof-client-ipc-flood-test.c +4 -3
@@ -219,9 +219,10 @@ static ssize_t sof_ipc_flood_dfs_write(struct file *file, const char __user *buf goto out; } -/* flood test */ - ret =sof_debug_ipc_flood_test (cdev, flood_duration_test, - ipc_duration_ms, ipc_count); + ret =sof_client_boot_dsp (cdev); +if (!ret) + ret =sof_debug_ipc_flood_test (cdev, flood_duration_test, + ipc_duration_ms, ipc_count); err =pm_runtime_put_autosuspend (dev);if (err <0 )
sound/soc/sof/sof-client-ipc-kernel-injector.c +3 -1
@@ -63,7 +63,9 @@ static ssize_t sof_kernel_msg_inject_dfs_write(struct file *file, const char __ureturn ret; } -sof_client_ipc_rx_message (cdev, hdr, priv->kernel_buffer); + ret =sof_client_boot_dsp (cdev); +if (!ret) +sof_client_ipc_rx_message (cdev, hdr, priv->kernel_buffer); ret =pm_runtime_put_autosuspend (dev);if (ret <0 )
sound/soc/sof/sof-client-ipc-msg-injector.c +9 -5
@@ -131,11 +131,15 @@ static int sof_msg_inject_send_message(struct sof_client_dev *cdev)return ret; } -/* send the message */ - ret =sof_client_ipc_tx_message (cdev, priv->tx_buffer, priv->rx_buffer, - priv->max_msg_size); -if (ret) -dev_err (dev,"IPC message send failed: %d\n" , ret); + ret =sof_client_boot_dsp (cdev); +if (!ret) { +/* send the message */ + ret =sof_client_ipc_tx_message (cdev, priv->tx_buffer, + priv->rx_buffer, + priv->max_msg_size); +if (ret) +dev_err (dev,"IPC message send failed: %d\n" , ret); + } err =pm_runtime_put_autosuspend (dev);if (err <0 )
sound/soc/sof/sof-client-probes.c +20 -6
@@ -123,6 +123,10 @@ static int sof_probes_compr_set_params(struct snd_compr_stream *cstream,if (ret)return ret; + ret =sof_client_boot_dsp (cdev); +if (ret) +return ret; + ret = ipc->init (cdev, priv->extractor_stream_tag, rtd->dma_bytes);if (ret <0 ) {dev_err (dai->dev,"Failed to init probe: %d\n" , ret);
@@ -224,6 +228,10 @@ static ssize_t sof_probes_dfs_points_read(struct file *file, char __user *to, goto exit; } + ret =sof_client_boot_dsp (cdev); +if (ret) + goto pm_error; + ret = ipc->points_info (cdev, &desc, &num_desc, type);if (ret <0 ) goto pm_error;
@@ -312,9 +320,12 @@ sof_probes_dfs_points_write(struct file *file, const char __user *from, goto exit; } - ret = ipc->points_add (cdev, desc, bytes /sizeof (*desc)); -if (!ret) - ret = count; + ret =sof_client_boot_dsp (cdev); +if (!ret) { + ret = ipc->points_add (cdev, desc, bytes /sizeof (*desc)); +if (!ret) + ret = count; + } err =pm_runtime_put_autosuspend (dev);if (err <0 )
@@ -367,9 +378,12 @@ sof_probes_dfs_points_remove_write(struct file *file, const char __user *from, goto exit; } - ret = ipc->points_remove (cdev, &array[1 ], array[0 ]); -if (!ret) - ret = count; + ret =sof_client_boot_dsp (cdev); +if (!ret) { + ret = ipc->points_remove (cdev, &array[1 ], array[0 ]); +if (!ret) + ret = count; + } err =pm_runtime_put_autosuspend (dev);if (err <0 )
sound/soc/sof/sof-client.c +6 -0
@@ -486,6 +486,12 @@ enum sof_ipc_type sof_client_get_ipc_type(struct sof_client_dev *cdev) }EXPORT_SYMBOL_NS_GPL (sof_client_get_ipc_type,"SND_SOC_SOF_CLIENT" ); +int sof_client_boot_dsp (struct sof_client_dev *cdev) +{ +return snd_sof_boot_dsp_firmware (sof_client_dev_to_sof_dev (cdev)); +} +EXPORT_SYMBOL_NS_GPL (sof_client_boot_dsp,"SND_SOC_SOF_CLIENT" ); +/* module refcount management of SOF core */ int sof_client_core_module_get (struct sof_client_dev *cdev) {
sound/soc/sof/sof-client.h +3 -0
@@ -50,6 +50,9 @@ const struct sof_ipc_fw_version *sof_client_get_fw_version(struct sof_client_devsize_t sof_client_get_ipc_max_payload_size (struct sof_client_dev *cdev);enum sof_ipc_type sof_client_get_ipc_type (struct sof_client_dev *cdev); +/* DSP/firmware boot request */ +int sof_client_boot_dsp (struct sof_client_dev *cdev); +/* module refcount management of SOF core */ int sof_client_core_module_get (struct sof_client_dev *cdev);void sof_client_core_module_put (struct sof_client_dev *cdev);
Signature · 1 line
2.52.0
Peter Ujfalusi
maintainerPATCH 5/8 ASoC: SOF: Intel: hda-sdw-bpt: Add support for on-demand DSP boot
In reply to Peter UjfalusiIf on-demand DSP boot is used we need to make sure that the DSP is booted up - which might not be the case - since we need ChainDMA in normal, non DSPless mode for the BRA to work.
--- sound/soc/sof/intel/hda-sdw-bpt.c | 11 +++++++++++ 1 file changed, 11 insertions(+)
sound/soc/sof/intel/hda-sdw-bpt.c +11 -0
@@ -98,6 +98,17 @@ static int hda_sdw_bpt_dma_prepare(struct device *dev, struct hdac_ext_stream **struct hdac_ext_stream *bpt_stream;unsigned int format =HDA_CL_STREAM_FORMAT ; +if (!sdev->dspless_mode_selected) { +int ret; + +/* +* Make sure that the DSP is booted up, which might not be the +* case if the on-demand DSP boot is used +*/ + ret =snd_sof_boot_dsp_firmware (sdev); +if (ret) +return ret; + }/* * the baseline format needs to be adjusted to * bandwidth requirements
Signature · 1 line
2.52.0
Peter Ujfalusi
maintainerPATCH 6/8 ASoC: SOF: Intel: pci-lnl: Set on_demand_dsp_boot for LNL
In reply to Peter UjfalusiLNL can be used with on-demand DSP booting, set the flag to enable it.
--- sound/soc/sof/intel/pci-lnl.c | 1 + 1 file changed, 1 insertion(+)
sound/soc/sof/intel/pci-lnl.c +1 -0
@@ -40,6 +40,7 @@ static const struct sof_dev_desc lnl_desc = { .ipc_supported_mask = BIT(SOF_IPC_TYPE_4), .ipc_default = SOF_IPC_TYPE_4, .dspless_mode_supported = true, + .on_demand_dsp_boot = true, .default_fw_path = { [SOF_IPC_TYPE_4] = "intel/sof-ipc4/lnl", },
Signature · 1 line
2.52.0
Peter Ujfalusi
maintainerPATCH 7/8 ASoC: SOF: Intel: pci-ptl: Set on_demand_dsp_boot for PTL and WCL
In reply to Peter UjfalusiPTL and WCL can be used with on-demand DSP booting, set the flag to enable it.
--- sound/soc/sof/intel/pci-ptl.c | 2 ++ 1 file changed, 2 insertions(+)
sound/soc/sof/intel/pci-ptl.c +2 -0
@@ -38,6 +38,7 @@ static const struct sof_dev_desc ptl_desc = { .ipc_supported_mask = BIT(SOF_IPC_TYPE_4), .ipc_default = SOF_IPC_TYPE_4, .dspless_mode_supported = true, + .on_demand_dsp_boot = true, .default_fw_path = { [SOF_IPC_TYPE_4] = "intel/sof-ipc4/ptl", },
@@ -67,6 +68,7 @@ static const struct sof_dev_desc wcl_desc = { .ipc_supported_mask = BIT(SOF_IPC_TYPE_4), .ipc_default = SOF_IPC_TYPE_4, .dspless_mode_supported = true, + .on_demand_dsp_boot = true, .default_fw_path = { [SOF_IPC_TYPE_4] = "intel/sof-ipc4/wcl", },
Signature · 1 line
2.52.0
Peter Ujfalusi
maintainerPATCH 8/8 ASoC: SOF: Intel: pci-nvl: Set on_demand_dsp_boot for NVL-S
In reply to Peter UjfalusiNVL-S can be used with on-demand DSP booting, set the flag to enable it.
--- sound/soc/sof/intel/pci-nvl.c | 1 + 1 file changed, 1 insertion(+)
sound/soc/sof/intel/pci-nvl.c +1 -0
@@ -38,6 +38,7 @@ static const struct sof_dev_desc nvl_s_desc = { .ipc_supported_mask = BIT(SOF_IPC_TYPE_4), .ipc_default = SOF_IPC_TYPE_4, .dspless_mode_supported = true, + .on_demand_dsp_boot = true, .default_fw_path = { [SOF_IPC_TYPE_4] = "intel/sof-ipc4/nvl-s", },
Signature · 1 line
2.52.0
Mark Brown
maintainerQuoted 9 lines · Peter Ujfalusi
On system suspend / resume we always power up the DSP and boot the firmware, which is not strictly needed as right after the firmware booted up we power the DSP down again on suspend and we also power it down after resume after some inactivity.
Similarly, on jack insert/removal we needlesly boot up the firmware to check the jack status, which needs no DSP/firmware communication.
[...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thanks!
[1/8] ASoC: SOF: ipc4-loader: Remove redundant rpm resume_and_get from load_library
commit: b8e54b447cdec234f0e0d80487af9540063d17dd
[2/8] ASoC: SOF: control: skip rpm calls in ext_volatile_get if not implemented
commit: 2c77ff200f59103ecdee60c00818a43cee38a6b8
[3/8] ASoC: SOF: Add support for on-demand DSP boot
commit: c3e1549811747e4b4ff7e4bba691980d9dab2d9e
[4/8] ASoC: SOF: sof-client: Add support for on-demand DSP boot
commit: 2cf7a9ced3c1a999f7de8711cb2a212557fbd800
[5/8] ASoC: SOF: Intel: hda-sdw-bpt: Add support for on-demand DSP boot
commit: d4e34f4ef88fc48a09b654bbe1b23c6788e7844a
[6/8] ASoC: SOF: Intel: pci-lnl: Set on_demand_dsp_boot for LNL
commit: 6780fb864d5b80f20694c9141036717b23190150
[7/8] ASoC: SOF: Intel: pci-ptl: Set on_demand_dsp_boot for PTL and WCL
commit: aabcb01353013d38533ba4346b6ca84bff1b96f0
[8/8] ASoC: SOF: Intel: pci-nvl: Set on_demand_dsp_boot for NVL-S
commit: f25c7d709b93602ee9a08eba522808a18e1f5d56All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark