Skip to contentSkip to conversation

"htt version request timed out" with the last 4.1.1.c1 firmware

DISCUSSION Paul Nuville 5 participants 8 messages Dec 9, 2017 – Dec 20, 2017 2 messages not in the archive Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

#2 lore raw

Hello all,

I've installed Archlinux on a Samsung Galaxy Book 10.6", and I'm trying to set up the wifi. The only firmware that seems to be suitable is the lastest 4.1.1.c1 one. But I've some errors and neither ip ad networkmanager are able to set up the wlan interface.
Here are some outputs :

# lspci -k
01:00.0 Network controller: Qualcomm Atheros QCA6174 802.11ac Wireless Network 
Adapter (rev 32)
        Subsystem: Samsung Electronics Co Ltd QCA6174 802.11ac Wireless 
Network Adapter
        Kernel modules: ath10k_pci
# lsmod | grep ath10k
ath10k_pci             53248  0
ath10k_core           356352  1 ath10k_pci
ath                    32768  1 ath10k_core
mac80211              827392  1 ath10k_core
cfg80211              647168  3 mac80211,ath,ath10k_core
# dmesg | grep ath10k
[ 1777.602748] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 
reset_mode 0
[ 1777.861498] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-
cal-pci-0000:01:00.0.bin failed with error -2
[ 1777.861509] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-
pci-0000:01:00.0.bin failed with error -2
[ 1777.861572] ath10k_pci 0000:01:00.0: invalid firmware magic
[ 1777.861587] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/
QCA6174/hw3.0/firmware-5.bin failed with error -2
[ 1777.861815] ath10k_pci 0000:01:00.0: qca6174 hw3.2 target 0x05030000 
chip_id 0x00340aff sub 144d:c150
[ 1777.861817] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 
0 testmode 0
[ 1777.862589] ath10k_pci 0000:01:00.0: firmware ver WLAN.RM.2.0-00180-
QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5
[ 1777.926402] ath10k_pci 0000:01:00.0: failed to fetch board data for 
bus=pci,vendor=168c,device=003e,subsystem-vendor=144d,subsystem-device=c150 
from ath10k/QCA6174/hw3.0/board-2.bin
[ 1777.926428] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 
ed5f849a
[ 1781.596516] ath10k_pci 0000:01:00.0: htt version request timed out
[ 1781.596523] ath10k_pci 0000:01:00.0: failed to setup htt: -110
[ 1781.669496] ath10k_pci 0000:01:00.0: could not init core (-110)
[ 1781.669544] ath10k_pci 0000:01:00.0: could not probe fw (-110)

Any help will be apreciate !

Thank you in advance,

Paul

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#3 lore raw
Quoted 6 lines · Paul Nuville

I've installed Archlinux on a Samsung Galaxy Book 10.6", and I'm trying to set up the wifi. The only firmware that seems to be suitable is the lastest 4.1.1.c1 one. But I've some errors and neither ip ad networkmanager are able to set up the wlan interface.
Here are some outputs :

[...]

Quoted 4 lines
[ 1777.861815] ath10k_pci 0000:01:00.0: qca6174 hw3.2 target 0x05030000 
chip_id 0x00340aff sub 144d:c150
[ 1777.861817] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 

0 testmode 0

Quoted 8 lines
[ 1777.862589] ath10k_pci 0000:01:00.0: firmware ver WLAN.RM.2.0-00180-
QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5
[ 1777.926402] ath10k_pci 0000:01:00.0: failed to fetch board data for 
bus=pci,vendor=168c,device=003e,subsystem-vendor=144d,subsystem-device=c150 
from ath10k/QCA6174/hw3.0/board-2.bin
[ 1777.926428] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 
ed5f849a
[ 1781.596516] ath10k_pci 0000:01:00.0: htt version request timed out

ath10k didn't file the correct board file from board-2.bin. Try updating to the latest board-2.bin:

https://github.com/kvalo/ath10k-firmware/blob/master/QCA6174/hw3.0/board-2.bin

The md5sum should be:

eddaa17fa2092bcd6713720116e421f1

Signature · 5 lines
Kalle Valo
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#5 lore raw
Quoted 6 lines · Adrian Chadd

Hi,

I've had this issue with a 4.11 update from QSDK (4.0.8.) ILQ-1.1.8 worked fine with ye olde backports.

Is it really just a board-2.bin issue? I tried it and it didn't fix it.

The case Paul has seems due to the correct board file missing. Not sure what issue you're seeing? any logs?

Also the issue is for QCA6174, does your QSDK 4.0.8 run with QCA6174?

Signature · 6 lines
Ryan Hsu

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#6 lore raw

Hi,

* QSDK 4.0.8 doesn't run with QCA6174 - HTT timeout as above
* QSDK ILQ 1.1.8 runs with QCA6174
* The HTT debugging shows that after the HTC/HTT stuff is setup, none of the HTT "i'm awake" messages are coming back.

I'll try the latest firmware and board data from Kalle's repository and see if that makes a difference. Right now I'm about 2/3rds the way through undoing the 1.1.8 -> 4.0.8 changes in ath10k to see if I can narrow down the actual regression.

-adrian

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#7 lore raw

hi,

fyi - i tried the latest board-2.bin and firmware-6.bin from kvalo's ath10k repository - still getting HTT timeouts. This is on the QSDK 4.0.8 backports.

-adrian

Quoted 15 lines · Adrian Chadd

Hi,

* QSDK 4.0.8 doesn't run with QCA6174 - HTT timeout as above
* QSDK ILQ 1.1.8 runs with QCA6174
* The HTT debugging shows that after the HTC/HTT stuff is setup, none of the HTT "i'm awake" messages are coming back.

I'll try the latest firmware and board data from Kalle's repository and see if that makes a difference. Right now I'm about 2/3rds the way through undoing the 1.1.8 -> 4.0.8 changes in ath10k to see if I can narrow down the actual regression.

Quoted 1 line

-adrian

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#8 lore raw

lastest firmware 9984 (10.3-3.4.104)

with the most recent 10.3-3.4.104 firmware for 9984 i see this ath10k message

[ 2884.160502] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode
[ 2884.160545] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode
[ 2884.167760] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode
[ 2884.175905] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode

in addition there is a problem since a long time in wds ap mode. all wpa sta stations (no matter which chipset, ath9k and ath10k tests) gets kicked out at wpa rekeying. (and reconnect immediatly) this problem exists on 99x0 and 9984 but not on 988x

any ideas?

Sebastian

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#9 lore raw
In reply to Kalle Valo
Quoted 22 lines · Kalle Valo
Quoted 6 lines · Paul Nuville

I've installed Archlinux on a Samsung Galaxy Book 10.6", and I'm trying to set up the wifi. The only firmware that seems to be suitable is the lastest 4.1.1.c1 one. But I've some errors and neither ip ad networkmanager are able to set up the wlan interface.
Here are some outputs :

[...]

Quoted 4 lines
[ 1777.861815] ath10k_pci 0000:01:00.0: qca6174 hw3.2 target 0x05030000 
chip_id 0x00340aff sub 144d:c150
[ 1777.861817] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 

0 testmode 0

Quoted 8 lines
[ 1777.862589] ath10k_pci 0000:01:00.0: firmware ver WLAN.RM.2.0-00180-
QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5
[ 1777.926402] ath10k_pci 0000:01:00.0: failed to fetch board data for 
bus=pci,vendor=168c,device=003e,subsystem-vendor=144d,subsystem-device=c150 
from ath10k/QCA6174/hw3.0/board-2.bin
[ 1777.926428] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 
ed5f849a
[ 1781.596516] ath10k_pci 0000:01:00.0: htt version request timed out
Quoted 8 lines

ath10k didn't file the correct board file from board-2.bin. Try updating to the latest board-2.bin:

https://github.com/kvalo/ath10k-firmware/blob/master/QCA6174/hw3.0/board-2.bin

The md5sum should be:

eddaa17fa2092bcd6713720116e421f1

Other than updating the board-2.bin file, you might also want to make sure you update the firmware file. I saw you're still using the Rm2.0 instead of the 4.4.1.c1 you asked.

Signature · 6 lines
Ryan Hsu

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k