doc: clarify sisfb notes and fix minor wording issues
Subsystems (5)
PATCH 1/1 doc: clarify sisfb notes and fix minor wording issues
Signed-off-by George Jones <[email protected]>
--- Documentation/fb/sisfb.rst | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
Documentation/fb/sisfb.rst +1 -1
@@ -49,7 +49,7 @@ Example for sisfb as a module: Start sisfb by typing:: modprobe sisfb mode=1024x768x16 rate=75 mem=12288 -A common mistake is that folks use a wrong parameter format when using the +A common mistake is that people use a wrong parameter format when using the driver compiled into the kernel. Please note: If compiled into the kernel, the parameter format is video=sisfb:mode:none or video=sisfb:mode:1024x768x16 (or whatever mode you want to use, alternatively using any other format
Signature · 1 line
2.43.0
PATCH 1/1 doc: clarify wording for FlashPoint system ordering
Signed-off-by George Jones <[email protected]>
--- Documentation/scsi/FlashPoint.rst | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
Documentation/scsi/FlashPoint.rst +1 -1
@@ -97,7 +97,7 @@ Contact: After this problem was identified, BusLogic contacted its major OEM customers to make sure the BT-946C/956C MultiMaster cards would still be - made available, and that Linux users who mistakenly ordered systems with + made available, and that Linux users who accidently ordered systems with the FlashPoint would be able to upgrade to the BT-946C. While this helped many purchasers of new systems, it was only a partial solution to the overall problem of FlashPoint support for Linux users. It did nothing to
Signature · 1 line
2.43.0
PATCH 1/1 doc: clarify wording for ntrig sensor disconnect behavior
In reply to George JonesSigned-off-by George Jones <[email protected]>
--- Documentation/input/devices/ntrig.rst | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
Documentation/input/devices/ntrig.rst +1 -1
@@ -41,7 +41,7 @@ The following parameters are used to configure filters to reduce noise: When the last finger is removed from the device, it sends a number of empty frames. By holding off on deactivation for a few frames we can tolerate false -erroneous disconnects, where the sensor may mistakenly not detect a finger that +erroneous disconnects, where the sensor may fail to detect a finger that is still present. Thus deactivate_slack addresses problems where a users might see breaks in lines during drawing, or drop an object during a long drag.
Signature · 1 line
2.43.0
PATCH 1/1 doc: fix typo in coding-style documentation (reformat)
In reply to George JonesFrom: Zack Mackintire <[email protected]>
Signed-off-by Zack Mackintire <[email protected]>
--- Documentation/process/coding-style.rst | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
Documentation/process/coding-style.rst +1 -1
@@ -719,7 +719,7 @@ re-formatting you may want to take a look at the man page. But remember: ``indent`` is not a fix for bad programming. Note that you can also use the ``clang-format`` tool to help you with -these rules, to quickly re-format parts of your code automatically, +these rules, to quickly reformat parts of your code automatically, and to review full files in order to spot coding style mistakes, typos and possible improvements. It is also handy for sorting ``#includes``, for aligning variables/macros, for reflowing text and other similar tasks.
Signature · 1 line
2.43.0
PATCH 1/1 doc: fix typo in serial-console documentation
In reply to George JonesSigned-off-by George Jones <[email protected]>
--- Documentation/admin-guide/serial-console.rst | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
Documentation/admin-guide/serial-console.rst +1 -1
@@ -55,7 +55,7 @@ times. In this case, there are the following two rules: subsystems. This rule is used also when the last console= parameter is not used - for other reasons. For example, because of a typo or because + for other reasons. For example, due to a typo or the hardware is not available. The result might be surprising. For example, the following two command
Signature · 1 line
2.43.0