ASoC: Add TAS67524 quad-channel Class-D amplifier driver

new file mode 100644
index 000000000000..812a4d39e2a5
@@ -0,0 +1,280 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/ti,tas67524.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments TAS67524 Audio Amplifier
+
+maintainers:
+  - Sen Wang <[email protected]>
+
+description:
+  The TAS67524 is a four-channel, digital-input, automotive
+  Class-D audio amplifier with load diagnostics and an integrated
+  DSP for audio processing.
+
+allOf:
+  - $ref: dai-common.yaml#
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - ti,tas6754
+          - const: ti,tas67524
+      - const: ti,tas67524
+
+  reg:
+    maxItems: 1
+
+  '#sound-dai-cells':
+    const: 1
+    description: |
+      The device exposes three DAIs, selected by index.
+        0 - Standard Audio Path (Playback)
+        1 - Low-Latency Playback Path (Playback)
+        2 - Sensory Feedback (Capture - Vpredict and Isense)
+      By default, all four channels of each DAI are active.
+
+  interrupts:
+    maxItems: 1
+    description:
+      Active-low falling-edge interrupt from the FAULT pin. When provided,
+      the driver uses IRQ-driven fault reporting instead of polling.
+
+  powerdown-gpios:
+    maxItems: 1
+    description:
+      GPIO connected to the PD pin, active low. Controls the internal
+      digital circuitry power state. When asserted the device enters
+      full power-down mode and all register state is lost. Can be omitted if
+      PD pin is hardwired or externally controlled.
+
+  standby-gpios:
+    maxItems: 1
+    description:
+      GPIO connected to the STBY pin, active low. Controls the analog
+      power stage. When asserted the device enters Deep Sleep mode but
+      remains I2C-accessible with registers retained. Can be omitted if
+      STBY pin is tied to PD or hardwired.
+
+  dvdd-supply:
+    description:
+      Digital logic supply (1.62 V to 3.6 V). All three supply rails must
+      be within their recommended operating ranges before the PD pin is
+      released.
+
+  pvdd-supply:
+    description:
+      Output FET power supply (4.5 V to 19 V). All three supply rails must
+      be within their recommended operating ranges before the PD pin is
+      released.
+
+  vbat-supply:
+    description:
+      Battery supply for the Class-D output stage (4.5 V to 19 V). Optional
+      when PVDD and VBAT are connected to the same supply rail. When absent,
+      VBAT is assumed hardwired to PVDD.
+
+  ti,fast-boot:
+    type: boolean
+    description:
+      Skip DC load diagnostic sweep at power-on to reduce boot latency.
+      Automatic diagnostics after fault conditions remain enabled. Hardware
+      overcurrent protection is always active.
+
+  ti,audio-slot-no:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      TDM slot offset for the standard audio playback path via SDIN1. A value
+      of 4 maps to slot 4. If omitted, slot assignment is derived from the
+      tx_mask provided via set_tdm_slot(). Without either property, no slot
+      mapping is configured.
+
+  ti,llp-slot-no:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      TDM slot offset for the low-latency playback path via SDIN1. If omitted,
+      slot assignment is derived from the tx_mask provided via set_tdm_slot().
+      Without either property, no slot mapping is configured. Disabled outside
+      of LLP mode, and only relevant for TDM formats.
+
+  ti,vpredict-slot-no:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      In TDM mode, enables Vpredict output and assigns its starting slot;
+      four consecutive slots carry Vpredict Ch1-4 on SDOUT1. May coexist
+      with ti,isense-slot-no using separate non-overlapping slots.
+
+      In I2S mode, enables Vpredict output on SDOUT1 (Ch1/Ch2) and SDOUT2
+      (Ch3/Ch4). The slot value is unused. Requires a GPIO configured as
+      sdout2 for Ch3/Ch4; without it only Ch1/Ch2 are output. Mutually
+      exclusive with ti,isense-slot-no; if both are set, Vpredict takes
+      priority.
+
+      Irrelevant in Left-J and Right-J modes.
+
+  ti,isense-slot-no:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      In TDM mode, enables Isense output and assigns its starting slot;
+      four consecutive slots carry Isense Ch1-4 on SDOUT1. May coexist
+      with ti,vpredict-slot-no using separate non-overlapping slots.
+
+      In I2S mode, enables Isense output on SDOUT1 (Ch1/Ch2) and SDOUT2
+      (Ch3/Ch4). The slot value is unused. Requires a GPIO configured as
+      SDOUT2 for Ch3/Ch4; without it only Ch1/Ch2 are output. Mutually
+      exclusive with ti,vpredict-slot-no; Vpredict takes priority if both
+      are set.
+
+      Irrelevant in Left-J and Right-J modes.
+
+  ti,gpio1-function:
+    $ref: /schemas/types.yaml#/definitions/string
+    description:
+      Function for the GPIO_1 pin. When omitted, GPIO_1 remains in its
+      power-on default state.
+    enum:
+      - low            # Output: driven low
+      - auto-mute      # Output: high when all channels are auto-muted
+      - auto-mute-ch4  # Output: high when channel 4 is auto-muted
+      - auto-mute-ch3  # Output: high when channel 3 is auto-muted
+      - auto-mute-ch2  # Output: high when channel 2 is auto-muted
+      - auto-mute-ch1  # Output: high when channel 1 is auto-muted
+      - sdout2         # Output: Routes secondary serial data output 2
+      - sdout1         # Output: Re-routes secondary serial data output 1
+      - warn           # Output: warning signal (OTW, CBC)
+      - fault          # Output: fault signal (OTSD, OC, DC)
+      - clock-sync     # Output: clock synchronisation
+      - invalid-clock  # Output: high when clock is invalid
+      - high           # Output: driven high
+      - mute           # Input: external mute control
+      - phase-sync     # Input: phase synchronisation
+      - sdin2          # Input: secondary SDIN2 for I2S/LJ/RJ ch3/ch4
+      - deep-sleep     # Input: asserted transitions device to Deep Sleep
+      - hiz            # Input: asserted transitions device to Hi-Z
+      - play           # Input: asserted transitions device to Play
+      - sleep          # Input: asserted transitions device to Sleep
+
+  ti,gpio2-function:
+    $ref: /schemas/types.yaml#/definitions/string
+    description:
+      Function for the GPIO_2 pin. When omitted, GPIO_2 remains in its
+      power-on default state.
+    enum:
+      - low            # Output: driven low
+      - auto-mute      # Output: high when all channels are auto-muted
+      - auto-mute-ch4  # Output: high when channel 4 is auto-muted
+      - auto-mute-ch3  # Output: high when channel 3 is auto-muted
+      - auto-mute-ch2  # Output: high when channel 2 is auto-muted
+      - auto-mute-ch1  # Output: high when channel 1 is auto-muted
+      - sdout2         # Output: Routes secondary serial data output 2
+      - sdout1         # Output: Re-routes secondary serial data output 1
+      - warn           # Output: warning signal (OTW, CBC)
+      - fault          # Output: fault signal (OTSD, OC, DC)
+      - clock-sync     # Output: clock synchronisation
+      - invalid-clock  # Output: high when clock is invalid
+      - high           # Output: driven high
+      - mute           # Input: external mute control
+      - phase-sync     # Input: phase synchronisation
+      - sdin2          # Input: secondary SDIN2 for I2S/LJ/RJ ch3/ch4
+      - deep-sleep     # Input: asserted transitions device to Deep Sleep
+      - hiz            # Input: asserted transitions device to Hi-Z
+      - play           # Input: asserted transitions device to Play
+      - sleep          # Input: asserted transitions device to Sleep
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    properties:
+      port@0:
+        $ref: audio-graph-port.yaml#
+        unevaluatedProperties: false
+        description: Standard audio playback port (DAI 0).
+
+      port@1:
+        $ref: audio-graph-port.yaml#
+        unevaluatedProperties: false
+        description: Low-latency playback port (LLP) (DAI 1).
+
+      port@2:
+        $ref: audio-graph-port.yaml#
+        unevaluatedProperties: false
+        description: Sensory feedback capture port (DAI 2).
+
+  port:
+    $ref: audio-graph-port.yaml#
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - '#sound-dai-cells'
+  - dvdd-supply
+  - pvdd-supply
+
+anyOf:
+  - required: [powerdown-gpios]
+  - required: [standby-gpios]
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        amplifier@70 {
+            compatible = "ti,tas67524";
+            reg = <0x70>;
+            #sound-dai-cells = <1>;
+            sound-name-prefix = "TAS0";
+
+            standby-gpios = <&main_gpio0 33 GPIO_ACTIVE_LOW>;
+
+            dvdd-supply = <&dvdd_1v8>;
+            pvdd-supply = <&pvdd_12v>;
+            vbat-supply = <&vbat_12v>;
+
+            ti,audio-slot-no = <0>;
+            ti,llp-slot-no = <4>;
+            ti,vpredict-slot-no = <0>;
+            ti,isense-slot-no = <4>;
+
+            ti,gpio2-function = "warn";
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+
+                    tas0_audio_ep: endpoint {
+                        dai-format = "dsp_b";
+                        remote-endpoint = <&be_tas0_audio_ep>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+
+                    tas0_anc_ep: endpoint {
+                        remote-endpoint = <&be_tas0_anc_ep>;
+                    };
+                };
+
+                port@2 {
+                    reg = <2>;
+
+                    tas0_fb_ep: endpoint {
+                        remote-endpoint = <&be_tas0_fb_ep>;
+                    };
+                };
+            };
+        };
+    };

index f9e6a83e55c6..28a976f32d9f 100644
@@ -275,6 +275,7 @@ config SND_SOC_ALL_CODECS
 	imply SND_SOC_TAS571X
 	imply SND_SOC_TAS5720
 	imply SND_SOC_TAS6424
+	imply SND_SOC_TAS675X
 	imply SND_SOC_TDA7419
 	imply SND_SOC_TFA9879
 	imply SND_SOC_TFA989X

@@ -2240,6 +2241,16 @@ config SND_SOC_TAS6424
 	  Enable support for Texas Instruments TAS6424 high-efficiency
 	  digital input quad-channel Class-D audio power amplifiers.
 
+config SND_SOC_TAS675X
+	tristate "Texas Instruments TAS675x Quad-Channel Audio Amplifier"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  Enable support for Texas Instruments TAS675x quad-channel Class-D
+	  audio power amplifier. The device supports I2S and TDM interfaces
+	  with real-time voltage and current sense feedback via SDOUT, and
+	  provides DC/AC/real-time load diagnostics for speaker monitoring.
+
 config SND_SOC_TDA7419
 	tristate "ST TDA7419 audio processor"
 	depends on I2C

index 172861d17cfd..106fdc140d42 100644
@@ -318,6 +318,7 @@ snd-soc-tas571x-y := tas571x.o
 snd-soc-tas5720-y := tas5720.o
 snd-soc-tas5805m-y := tas5805m.o
 snd-soc-tas6424-y := tas6424.o
+snd-soc-tas675x-y := tas675x.o
 snd-soc-tda7419-y := tda7419.o
 snd-soc-tas2770-y := tas2770.o
 snd-soc-tas2781-comlib-y := tas2781-comlib.o

@@ -760,6 +761,7 @@ obj-$(CONFIG_SND_SOC_TAS571X)	+= snd-soc-tas571x.o
 obj-$(CONFIG_SND_SOC_TAS5720)	+= snd-soc-tas5720.o
 obj-$(CONFIG_SND_SOC_TAS5805M)	+= snd-soc-tas5805m.o
 obj-$(CONFIG_SND_SOC_TAS6424)	+= snd-soc-tas6424.o
+obj-$(CONFIG_SND_SOC_TAS675X)	+= snd-soc-tas675x.o
 obj-$(CONFIG_SND_SOC_TDA7419)	+= snd-soc-tda7419.o
 obj-$(CONFIG_SND_SOC_TAS2770) += snd-soc-tas2770.o
 obj-$(CONFIG_SND_SOC_TFA9879)	+= snd-soc-tfa9879.o

index 2cb95d87bbef..7594d0a38d6b 100644
@@ -7,3 +7,4 @@ Codec-Specific Information
    :maxdepth: 2
 
    cs35l56
+   tas675x

686 lines not on this page · raw message

index a626dee5c106..a78b6cb9b907 100644
@@ -26191,17 +26191,20 @@ TEXAS INSTRUMENTS AUDIO (ASoC/HDA) DRIVERS
 M:	Shenghao Ding <[email protected]>
 M:	Kevin Lu <[email protected]>
 M:	Baojun Xu <[email protected]>
+M:	Sen Wang <[email protected]>
 L:	[email protected]
 S:	Maintained
 F:	Documentation/devicetree/bindings/sound/ti,tas2552.yaml
 F:	Documentation/devicetree/bindings/sound/ti,tas2562.yaml
 F:	Documentation/devicetree/bindings/sound/ti,tas2770.yaml
 F:	Documentation/devicetree/bindings/sound/ti,tas27xx.yaml
+F:	Documentation/devicetree/bindings/sound/ti,tas67524.yaml
 F:	Documentation/devicetree/bindings/sound/ti,tpa6130a2.yaml
 F:	Documentation/devicetree/bindings/sound/ti,pcm1681.yaml
 F:	Documentation/devicetree/bindings/sound/ti,pcm3168a.yaml
 F:	Documentation/devicetree/bindings/sound/ti,tlv320*.yaml
 F:	Documentation/devicetree/bindings/sound/ti,tlv320adcx140.yaml
+F:	Documentation/sound/codecs/tas675x*
 F:	include/sound/tas2*.h
 F:	include/sound/tlv320*.h
 F:	sound/hda/codecs/side-codecs/tas2781_hda_i2c.c

@@ -26215,6 +26218,7 @@ F:	sound/soc/codecs/pcm3168a*.*
 F:	sound/soc/codecs/pcm5102a.c
 F:	sound/soc/codecs/pcm512x*.*
 F:	sound/soc/codecs/tas2*.*
+F:	sound/soc/codecs/tas675x*.*
 F:	sound/soc/codecs/tlv320*.*
 F:	sound/soc/codecs/tpa6130a2.*