Skip to contentSkip to conversation

board: dhelectronics: imx: Use second Ethernet MAC also from fuse

PATCH In review Christoph Niedermaier 3 participants 4 messages Apr 15 – Apr 22

Subsystems (2)
lore
Share & tools
lore

Christoph Niedermaier

author maintainer
#0 lore raw

PATCH v3 1/1 board: dhelectronics: imx: Use second Ethernet MAC also from fuse

Currently, the board specific code evaluates only the first Ethernet MAC address fuse, regardless of whether the first or second MAC address is requested. When the function for determine the second Ethernet MAC address is looking for the fused MAC address, it only reads the first MAC address fuse and increment it by one to set the second Ethernet MAC address. That is not the expected behavior when two MAC addresses are fused, because this causes the second fused MAC address to be ignored. Change this so that the second fused MAC address will be used.

---
Cc: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Sam Protsenko <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: [email protected]
---
V2: - Change the commit message to be more precise
- Move index to the end of parameters to be consistent to the STM32MP plattform
- Remove fallback where the first MAC address fuse incremented by one is used
- Remove MAC Adress treatmeant for early prototypes
V3: - Revert removal of the MAC Adress treatmeant for early prototypes and
and remove the corresponding part from the commit message
- The Reviewed-by has now been properly ordered

---
 board/dhelectronics/common/dh_imx.c               | 4 ++--
 board/dhelectronics/common/dh_imx.h               | 3 ++-
 board/dhelectronics/dh_imx6/dh_imx6.c             | 2 +-
 board/dhelectronics/dh_imx8mp/imx8mp_dhcom_pdk2.c | 6 +++---
 4 files changed, 8 insertions(+), 7 deletions(-)
board/dhelectronics/common/dh_imx.c +2 -2
index 3d6487dd0d8..50404a66f9d 100644
@@ -10,13 +10,13 @@
 #include <net.h>
 #include "dh_imx.h"
 
-int dh_imx_get_mac_from_fuse(unsigned char *enetaddr)
+int dh_imx_get_mac_from_fuse(unsigned char *enetaddr, int index)
 {
 	/*
 	 * If IIM fuses contain valid MAC address, use it.
 	 * The IIM MAC address fuses are NOT programmed by default.
 	 */
-	imx_get_mac_from_fuse(0, enetaddr);
+	imx_get_mac_from_fuse(index, enetaddr);
 	if (!is_valid_ethaddr(enetaddr))
 		return -EINVAL;
 
board/dhelectronics/common/dh_imx.h +2 -1
index 284f8637fb8..be2ff5e076c 100644
@@ -7,6 +7,7 @@
  * dh_imx_get_mac_from_fuse - Get MAC address from fuse and write it to env
  *
  * @enetaddr: buffer where address is to be stored
+ * @index: index of MAC address in fuse (starts with 0)
  * Return: 0 if OK, other value on error
  */
-int dh_imx_get_mac_from_fuse(unsigned char *enetaddr);
+int dh_imx_get_mac_from_fuse(unsigned char *enetaddr, int index);
board/dhelectronics/dh_imx6/dh_imx6.c +1 -1
index 234824b38c2..c9e8107685a 100644
@@ -94,7 +94,7 @@ int dh_setup_mac_address(struct eeprom_id_page *eip)
 	if (dh_get_mac_is_enabled("ethernet0"))
 		return 0;
 
-	if (!dh_imx_get_mac_from_fuse(enetaddr))
+	if (!dh_imx_get_mac_from_fuse(enetaddr, 0))
 		goto out;
 
 	if (!dh_get_mac_from_eeprom(enetaddr, "eeprom0"))
board/dhelectronics/dh_imx8mp/imx8mp_dhcom_pdk2.c +3 -3
index 3424be10936..486073392e9 100644
@@ -47,7 +47,7 @@ static int dh_imx8_setup_ethaddr(struct eeprom_id_page *eip)
 	if (dh_get_mac_is_enabled("ethernet0"))
 		return 0;
 
-	if (!dh_imx_get_mac_from_fuse(enetaddr))
+	if (!dh_imx_get_mac_from_fuse(enetaddr, 0))
 		goto out;
 
 	if (!dh_get_value_from_eeprom_buffer(DH_MAC0, enetaddr, sizeof(enetaddr), eip))
@@ -72,8 +72,8 @@ static int dh_imx8_setup_eth1addr(struct eeprom_id_page *eip)
 	if (dh_get_mac_is_enabled("ethernet1"))
 		return 0;
 
-	if (!dh_imx_get_mac_from_fuse(enetaddr))
-		goto increment_out;
+	if (!dh_imx_get_mac_from_fuse(enetaddr, 1))
+		goto out;
 
 	if (!dh_get_value_from_eeprom_buffer(DH_MAC1, enetaddr, sizeof(enetaddr), eip))
 		goto out;
Signature · 1 line
2.30.2
maintainer Reviewed-by on v3 1/1
#1 lore raw
Quoted 9 lines · Christoph Niedermaier

Currently, the board specific code evaluates only the first Ethernet MAC address fuse, regardless of whether the first or second MAC address is requested. When the function for determine the second Ethernet MAC address is looking for the fused MAC address, it only reads the first MAC address fuse and increment it by one to set the second Ethernet MAC address. That is not the expected behavior when two MAC addresses are fused, because this causes the second fused MAC address to be ignored. Change this so that the second fused MAC address will be used.

Thanks

maintainer
#2 lore raw
In reply to Christoph Niedermaier
Quoted 3 lines · Christoph Niedermaier

Currently, the board specific code evaluates only the first Ethernet MAC address fuse, regardless of whether the first or second MAC address is requested. When the function for determine the second

"the function _to_ determine" ... can this be fixed when applying ?

... and uh, odd, why is Fabio not on CC ? I don't think this patch will be picked up with him not on Cc.

reviewer
#3 lore raw
Quoted 4 lines · Marek Vasut

"the function _to_ determine" ... can this be fixed when applying ?

... and uh, odd, why is Fabio not on CC ? I don't think this patch will be picked up with him not on Cc.

I have fixed the typo and applied it, thanks.