m68k: dts: mcf5441x: add mmc device for mcf5441x
Subsystems (3)
PATCH v2 1/9 m68k: dts: mcf5441x: add mmc device for mcf5441x
Add mmc support for the mcf5441x family. There is only one esdhc controller for this cpu family.
--- arch/m68k/dts/mcf5441x.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/m68k/dts/mcf5441x.dtsi +8 -0
@@ -163,5 +163,13 @@ clock-frequency = <100000>; status = "disabled"; }; + + esdhc: mmc@0xfc0cc000 { + compatible = "fsl,esdhc"; + reg = <0xfc0cc000 0x8000>; + non-removable; + bus-width = <4>; + status = "disabled"; + }; }; };
Signature · 1 line
2.54.0
PATCH v2 4/9 board: stmark2: remove old garbage
Remove old erroneous garbage.
--- include/configs/stmark2.h | 1 - 1 file changed, 1 deletion(-)
include/configs/stmark2.h +0 -1
@@ -18,7 +18,6 @@"load mmc 0:1 ${loadaddr_ramfs} uRamfs\0" \"kern_size=0x700000\0" \"loadaddr=0x42000000\0" \ -"-(rootfs)\0" \"loadaddr_ramfs=0x43000000\0" \"update_uboot=loady ${loadaddr}; " \"sf probe 0:1 50000000; " \
Signature · 1 line
2.54.0
PATCH v2 5/9 mmc: Kconfig: allows m68k to use esdhc imx driver
In reply to Angelo DureghelloAllow cpu families as mcf5441x (m68k) to use the fsl_esdhc_imx driver since the hardware ip module is the same.
---
Changes in v2:
- moved before menuconfig changes
--- drivers/mmc/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mmc/Kconfig +1 -1
@@ -924,7 +924,7 @@ config ESDHCI_QUIRK_BROKEN_TIMEOUT_VALUE config FSL_ESDHC_IMX bool "Freescale/NXP i.MX eSDHC controller support" - depends on MACH_IMX + depends on MACH_IMX || M68K help This selects support for the i.MX eSDHC (Enhanced Secure Digital Host Controller) found on numerous Freescale/NXP SoCs.
Signature · 1 line
2.54.0
PATCH v2 2/9 m68k: dts: stmark2: enable esdhc
In reply to Angelo DureghelloEnable esdhc device.
--- arch/m68k/dts/stmark2.dts | 4 ++++ 1 file changed, 4 insertions(+)
arch/m68k/dts/stmark2.dts +4 -0
@@ -45,3 +45,7 @@ &i2c0 { status = "okay"; }; + +&esdhc { + status = "okay"; +};
Signature · 1 line
2.54.0
PATCH v2 3/9 board: stmark2: add sd boot command
In reply to Angelo DureghelloAdd command to boot from sd.
--- include/configs/stmark2.h | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
include/configs/stmark2.h +4 -1
@@ -14,9 +14,12 @@ board/sysam/stmark2/sbf_dram_init.o (.text*)#define CFG_EXTRA_ENV_SETTINGS \ + "boot_sd=load mmc 0:1 ${loadaddr} uImage; " \ + "load mmc 0:1 ${loadaddr_ramfs} uRamfs\0" \ "kern_size=0x700000\0" \ - "loadaddr=0x40001000\0" \ + "loadaddr=0x42000000\0" \ "-(rootfs)\0" \ + "loadaddr_ramfs=0x43000000\0" \ "update_uboot=loady ${loadaddr}; " \ "sf probe 0:1 50000000; " \ "sf erase 0 0x80000; " \
Signature · 1 line
2.54.0
PATCH v2 6/9 configs: stmark2: add support for mmc
In reply to Angelo DureghelloAdd support for mmc.
---
Changes in v2:
- recreated by make menuconfig
--- configs/stmark2_defconfig | 18 +++++++++++++----- 1 file changed, 13 insertions(+), 5 deletions(-)
configs/stmark2_defconfig +13 -5
@@ -3,19 +3,19 @@ CONFIG_TEXT_BASE=0x47E00000 CONFIG_SYS_MALLOC_LEN=0x40000 CONFIG_SF_DEFAULT_SPEED=50000000 CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x40000 +CONFIG_ENV_OFFSET=0x80000 CONFIG_ENV_SECT_SIZE=0x10000 CONFIG_DEFAULT_DEVICE_TREE="stmark2" -CONFIG_SYS_MONITOR_LEN=262144 -CONFIG_SYS_LOAD_ADDR=0x40010000 +CONFIG_SYS_MONITOR_LEN=327680 +CONFIG_SYS_LOAD_ADDR=0x42000000 CONFIG_TARGET_STMARK2=y CONFIG_SYS_BARGSIZE=256 CONFIG_SYS_MONITOR_BASE=0x47E00400 CONFIG_TIMESTAMP=y CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 rw rootfstype=ramfs rdinit=/bin/init devtmpfs.mount=1" +CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 rw rootfstype=ramfs rdinit=/sbin/init devtmpfs.mount=1" CONFIG_USE_BOOTCOMMAND=y -CONFIG_BOOTCOMMAND="sf probe 0:1 50000000; sf read ${loadaddr} 0x100000 ${kern_size}; bootm ${loadaddr}" +CONFIG_BOOTCOMMAND="run boot_sd; bootm ${loadaddr} ${loadaddr_ramfs}" CONFIG_SYS_PBSIZE=283 # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_SYS_MALLOC_BOOTPARAMS=y
@@ -28,9 +28,14 @@ CONFIG_SYS_PROMPT="stmark2 $ " # CONFIG_CMD_IMPORTENV is not set CONFIG_CMD_I2C=y # CONFIG_CMD_LOADS is not set +CONFIG_CMD_MMC=y CONFIG_CMD_SPI=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y CONFIG_CMD_MTDPARTS=y CONFIG_MTDIDS_DEFAULT="nor0=spi-flash.0" CONFIG_MTDPARTS_DEFAULT="mtdparts=spi-flash.0:1m(u-boot),7m(kernel),-(rootfs)"
@@ -42,6 +47,9 @@ CONFIG_HOSTNAME="stmark2" CONFIG_NO_NET=y CONFIG_DM_I2C=y CONFIG_SYS_I2C_FSL=y +CONFIG_MMC=y +CONFIG_FSL_ESDHC_IMX=y +CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y CONFIG_SPI_FLASH_ISSI=y
Signature · 1 line
2.54.0
PATCH v2 7/9 configs: stmark2: add bdinfo command
In reply to Angelo DureghelloEnable bdinfo command.
---
Changes in v2:
- recreated by make menuconfig
--- configs/stmark2_defconfig | 1 - 1 file changed, 1 deletion(-)
configs/stmark2_defconfig +0 -1
@@ -22,7 +22,6 @@ CONFIG_SYS_MALLOC_BOOTPARAMS=y CONFIG_HUSH_PARSER=y # CONFIG_CMDLINE_EDITING is not set CONFIG_SYS_PROMPT="stmark2 $ " -# CONFIG_CMD_BDI is not set # CONFIG_CMD_CONSOLE is not set # CONFIG_CMD_EXPORTENV is not set # CONFIG_CMD_IMPORTENV is not set
Signature · 1 line
2.54.0
PATCH v2 9/9 m68k: set proper u-boot image size for initial boot
In reply to Angelo DureghelloThere is a value of 256K hardcoded as u-boot image size. This produce bank tty as soon as the image size grows over the limit. Fix it by using value preset by CONFIG_SYS_MONITOR_LEN.
--- arch/m68k/cpu/mcf5445x/start.S | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
arch/m68k/cpu/mcf5445x/start.S +1 -2
@@ -114,7 +114,7 @@ vector192_255: /* Image header: chksum 4 bytes, len 4 bytes, img dest 4 bytes */ asm_sbf_img_hdr: .long 0x00000000 /* checksum, not yet implemented */ - .long 0x00040000 /* image length */ + .long CONFIG_SYS_MONITOR_LEN /* image length */ .long CONFIG_TEXT_BASE /* image to be relocated at */ asm_dram_init:
@@ -292,7 +292,6 @@ asm_dspi_rd_status: move.b (%a3), %d1 rts #endif /* CONFIG_CF_SBF */ - #ifdef CONFIG_SYS_NAND_BOOT /* copy 4 boot pages to dram as soon as possible */ /* each page is 996 bytes (1056 total with 60 ECC bytes */
Signature · 1 line
2.54.0
PATCH v2 8/9 m68k: mcf5441x: create stub to use imx drivers
In reply to Angelo DureghelloSome NXP imx hardware ip module as the esdhc controller are exactly the same in some new ColdFire cpus. For the specific case, mcf5441x needs to use the existing fsl_esdhc_imx.c driver for the esdhc device.
Create a stub to be able to use NXP "imx" serie drivers as the fsl_esdhc_imx in the ColdFire architecture.
--- arch/m68k/Kconfig | 1 + arch/m68k/include/asm/arch-mcf5445x/clock.h | 19 +++++++++++++++++ arch/m68k/lib/Makefile | 1 + arch/m68k/lib/clock.c | 23 +++++++++++++++++++++ 4 files changed, 44 insertions(+) create mode 100644 arch/m68k/include/asm/arch-mcf5445x/clock.h create mode 100644 arch/m68k/lib/clock.c
arch/m68k/Kconfig +1 -0
@@ -62,6 +62,7 @@ config MCF5441x select DM select DM_SERIAL select ARCH_COLDFIRE + select CREATE_ARCH_SYMLINK bool config M680x0
arch/m68k/include/asm/arch-mcf5445x/clock.h new file +19 -0
@@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* ColdFire clock support +* +* Copyright 2026 Kernelspace. +* Angelo Dureghello <[email protected]> +*/ + +#ifndef __CLOCK_H +#define __CLOCK_H + +/* Stub to use fsl/nxp drivers. */ +enum mxc_clock { +MXC_ESDHC_CLK , +}; + +int mxc_get_clock (enum mxc_clock clk); + +#endif /* __CLOCK_H */
arch/m68k/lib/Makefile +1 -0
@@ -9,3 +9,4 @@ lib-$(CONFIG_USE_PRIVATE_LIBGCC) += lshrdi3.o muldi3.o ashldi3.o ashrdi3.o obj-$(CONFIG_CMD_BOOTM) += bootm.o obj-$(CONFIG_ARCH_COLDFIRE) += cache.o interrupts.o time.o traps.o bdinfo.o fec.o +obj-$(CONFIG_MCF5441x) += clock.o
arch/m68k/lib/clock.c new file +23 -0
@@ -0,0 +1,23 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* (C) Copyright 2026 Kernelspace +* Angelo Dureghello <[email protected]> +*/ + +#include <config.h> +#include <asm/arch/clock.h> +#include <asm/global_data.h> + +DECLARE_GLOBAL_DATA_PTR ; +/* +* Stub to use existing nxp/fsl drivers. +*/ +int mxc_get_clock (enum mxc_clock clk) +{ +if (clk ==MXC_ESDHC_CLK ) +return gd->arch.sdhc_clk; + +printf ("Unsupported MXC CLK: %d\n" , clk); + +return 0 ; +}
Signature · 1 line
2.54.0