e1000e: Avoid DMA re-mapping on RX copybreak
Subsystems (2)
PATCH v2 1/1 e1000e: Avoid DMA re-mapping on RX copybreak
This patch factors out DMA re-mapping for skbs which were recycled in the RX path due to copybreak or errors. There is only one path out of the e1000_clean_rx_irq() loop where the skb is consumed and DMA needs to be re-mapped, so don't unmap it before checking the conditions.
The buffer allocation loop is adjusted to not assume that DMA is unmapped, handling mapping errors gracefully.
On systems with IOMMU enabled, the cost of re-mapping DMA is greater than the cost of copying data out of the ring buffer. When I use this patch and configure e1000e with copybreak=2048, my system with IOMMU completes RX twice as fast under load.
The kludge of unconditional unmapping has existed since this driver was introduced in 2007, inherited from the e1000 driver which has since factored it out. IOMMU tech was new at the time.
Tested on an I218-V.
---
v2:
* proofread description with Aleksandr
--- drivers/net/ethernet/intel/e1000e/netdev.c | 34 +++++++++++++++------- 1 file changed, 23 insertions(+), 11 deletions(-)
drivers/net/ethernet/intel/e1000e/netdev.c +23 -11
@@ -663,6 +663,8 @@ static void e1000_alloc_rx_buffers(struct e1000_ring *rx_ring, skb = buffer_info->skb;if (skb) {skb_trim (skb,0 ); +if (likely (buffer_info->dma)) + goto write_desc; goto map_skb; }
@@ -680,10 +682,12 @@ static void e1000_alloc_rx_buffers(struct e1000_ring *rx_ring, DMA_FROM_DEVICE);if (dma_mapping_error (&pdev->dev, buffer_info->dma)) {dev_err (&pdev->dev,"Rx DMA map failed\n" ); + buffer_info->dma =0 ; adapter->rx_dma_failed++;break ; } +write_desc: rx_desc =E1000_RX_DESC_EXT (*rx_ring, i); rx_desc->read.buffer_addr =cpu_to_le64 (buffer_info->dma);
@@ -941,7 +945,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,dma_rmb ();/* read descriptor and rx_buffer_info after status DD */ skb = buffer_info->skb; - buffer_info->skb =NULL ;prefetch (skb->data -NET_IP_ALIGN );
@@ -955,9 +958,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done, cleaned = true; cleaned_count++; -dma_unmap_single (&pdev->dev, buffer_info->dma, - adapter->rx_buffer_len,DMA_FROM_DEVICE ); - buffer_info->dma =0 ; length =le16_to_cpu (rx_desc->wb.upper.length);
@@ -973,8 +973,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,if (adapter->flags2 &FLAG2_IS_DISCARDING ) {/* All receives must fit into a single buffer */ e_dbg ("Receive packet consumed multiple buffers\n" ); -/* recycle */ - buffer_info->skb = skb;if (staterr &E1000_RXD_STAT_EOP ) adapter->flags2 &= ~FLAG2_IS_DISCARDING ; goto next_desc;
@@ -982,8 +980,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,if (unlikely ((staterr &E1000_RXDEXT_ERR_FRAME_ERR_MASK ) && !(netdev->features &NETIF_F_RXALL ))) { -/* recycle */ - buffer_info->skb = skb; goto next_desc; }
@@ -1010,19 +1006,35 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,struct sk_buff *new_skb =napi_alloc_skb (&adapter->napi, length);if (new_skb) { +dma_sync_single_for_cpu (&pdev->dev, + buffer_info->dma, + adapter->rx_buffer_len, +DMA_FROM_DEVICE );skb_copy_to_linear_data_offset (new_skb, -NET_IP_ALIGN , (skb->data -NET_IP_ALIGN ), (length +NET_IP_ALIGN )); -/* save the skb in buffer_info as good */ - buffer_info->skb = skb; +dma_sync_single_for_device (&pdev->dev, + buffer_info->dma, + adapter->rx_buffer_len, +DMA_FROM_DEVICE ); skb = new_skb; }/* else just continue with the old one */ } -/* end copybreak code */ + +/* If skb was not replaced by copybreak, we are consuming +* the original buffer and must release the DMA mapping. +*/ +if (skb == buffer_info->skb) { + buffer_info->skb =NULL ; +dma_unmap_single (&pdev->dev, buffer_info->dma, + adapter->rx_buffer_len, +DMA_FROM_DEVICE ); + buffer_info->dma =0 ; + }skb_put (skb, length);/* Receive Checksum Offload */
Signature · 1 line
2.43.0
Dear Matt,
Thank you for your patch.
Am 27.04.26 um 16:12 schrieb Matt Vollrath:
Quoted 5 lines
This patch factors out DMA re-mapping for skbs which were recycled in the RX path due to copybreak or errors. There is only one path out of the
e1000_clean_rx_irq()loop where the skb is consumed and DMA needs to be re-mapped, so don't unmap it before checking the conditions.
Quoted 7 lines
The buffer allocation loop is adjusted to not assume that DMA is unmapped, handling mapping errors gracefully.
On systems with IOMMU enabled, the cost of re-mapping DMA is greater than the cost of copying data out of the ring buffer. When I use this patch and configure e1000e with copybreak=2048, my system with IOMMU completes RX twice as fast under load.
It’d be great if you could document the benchmark, and described your system and shared the numbers.
Quoted 3 lines
The kludge of unconditional unmapping has existed since this driver was introduced in 2007, inherited from the e1000 driver which has since factored it out. IOMMU tech was new at the time.
Please share the commit factoring it out.
Also, what about systems where the IOMMU is disabled. (I think that is possible.)
Quoted 103 lines
Tested on an I218-V.
Assisted-by Claude:claude-4-7-opusSigned-off-by Matt Vollrath <[email protected]>Signed-off-by Aleksandr Loktionov <[email protected]>---
v2:
* proofread description with Aleksandr--- drivers/net/ethernet/intel/e1000e/netdev.c | 34 +++++++++++++++------- 1 file changed, 23 insertions(+), 11 deletions(-)drivers/net/ethernet/intel/e1000e/netdev.c +16
-11@@ -663,6 +663,8 @@ static void e1000_alloc_rx_buffers(struct e1000_ring *rx_ring, skb = buffer_info->skb;if (skb) {skb_trim (skb,0 ); +if (likely (buffer_info->dma)) + goto write_desc; goto map_skb; }@@ -680,10 +682,12 @@ static void e1000_alloc_rx_buffers(struct e1000_ring *rx_ring, DMA_FROM_DEVICE);if (dma_mapping_error (&pdev->dev, buffer_info->dma)) {dev_err (&pdev->dev,"Rx DMA map failed\n" ); + buffer_info->dma =0 ; adapter->rx_dma_failed++;break ; } +write_desc: rx_desc =E1000_RX_DESC_EXT (*rx_ring, i); rx_desc->read.buffer_addr =cpu_to_le64 (buffer_info->dma);@@ -941,7 +945,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,dma_rmb ();/* read descriptor and rx_buffer_info after status DD */ skb = buffer_info->skb; - buffer_info->skb =NULL ;prefetch (skb->data -NET_IP_ALIGN );@@ -955,9 +958,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done, cleaned = true; cleaned_count++; -dma_unmap_single (&pdev->dev, buffer_info->dma, - adapter->rx_buffer_len,DMA_FROM_DEVICE ); - buffer_info->dma =0 ; length =le16_to_cpu (rx_desc->wb.upper.length);@@ -973,8 +973,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,if (adapter->flags2 &FLAG2_IS_DISCARDING ) {/* All receives must fit into a single buffer */ e_dbg ("Receive packet consumed multiple buffers\n" ); -/* recycle */ - buffer_info->skb = skb;if (staterr &E1000_RXD_STAT_EOP ) adapter->flags2 &= ~FLAG2_IS_DISCARDING ; goto next_desc;@@ -982,8 +980,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,if (unlikely ((staterr &E1000_RXDEXT_ERR_FRAME_ERR_MASK ) && !(netdev->features &NETIF_F_RXALL ))) { -/* recycle */ - buffer_info->skb = skb; goto next_desc; }@@ -1010,19 +1006,35 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,struct sk_buff *new_skb =napi_alloc_skb (&adapter->napi, length);if (new_skb) { +dma_sync_single_for_cpu (&pdev->dev, + buffer_info->dma, + adapter->rx_buffer_len, +DMA_FROM_DEVICE );skb_copy_to_linear_data_offset (new_skb, -NET_IP_ALIGN , (skb->data -NET_IP_ALIGN ), (length +NET_IP_ALIGN )); -/* save the skb in buffer_info as good */ - buffer_info->skb = skb; +dma_sync_single_for_device (&pdev->dev, + buffer_info->dma, + adapter->rx_buffer_len, +DMA_FROM_DEVICE ); skb = new_skb; }/* else just continue with the old one */ } -/* end copybreak code */ + +/* If skb was not replaced by copybreak, we are consuming +* the original buffer and must release the DMA mapping. +*/
drivers/net/ethernet/intel/e1000e/netdev.c static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done, · line 1040
Quoted 10 lines
drivers/net/ethernet/intel/e1000e/netdev.c +7
-0+if (skb == buffer_info->skb) { + buffer_info->skb =NULL ; +dma_unmap_single (&pdev->dev, buffer_info->dma, + adapter->rx_buffer_len, +DMA_FROM_DEVICE ); + buffer_info->dma =0 ; + }skb_put (skb, length);/* Receive Checksum Offload */
Kind regards,
Paul
Quoted 21 lines · Paul Menzel
Dear Matt,
Thank you for your patch.
Am 27.04.26 um 16:12 schrieb Matt Vollrath:
Quoted 5 lines
This patch factors out DMA re-mapping for skbs which were recycled in the RX path due to copybreak or errors. There is only one path out of the
e1000_clean_rx_irq()loop where the skb is consumed and DMA needs to be re-mapped, so don't unmap it before checking the conditions.Quoted 7 lines
The buffer allocation loop is adjusted to not assume that DMA is unmapped, handling mapping errors gracefully.
On systems with IOMMU enabled, the cost of re-mapping DMA is greater than the cost of copying data out of the ring buffer. When I use this patch and configure e1000e with copybreak=2048, my system with IOMMU completes RX twice as fast under load.
It’d be great if you could document the benchmark, and described your system and shared the numbers.
Quoted 7 lines
Quoted 3 lines
The kludge of unconditional unmapping has existed since this driver was introduced in 2007, inherited from the e1000 driver which has since factored it out. IOMMU tech was new at the time.
Please share the commit factoring it out.
Also, what about systems where the IOMMU is disabled. (I think that is possible.)
Thanks Paul, I'll put in some benchmark details and cite the history.
At a glance, the performance impact on IOMMU-disabled or passthrough was marginal.
I'll also wait until tomorrow morning to post v3, jumped the gun this morning. No more revisions before breakfast!
Quoted 107 lines
Quoted 94 lines
Tested on an I218-V.
Assisted-by Claude:claude-4-7-opusSigned-off-by Matt Vollrath <[email protected]>Signed-off-by Aleksandr Loktionov <[email protected]>---
v2:
* proofread description with Aleksandr
---
drivers/net/ethernet/intel/e1000e/netdev.c| 34 +++++++++++++++-------1 file changed, 23 insertions(+), 11 deletions(-)drivers/net/ethernet/intel/e1000e/netdev.c +4
-0@@ -663,6 +663,8 @@ static void e1000_alloc_rx_buffers(struct e1000_ring *rx_ring, skb = buffer_info->skb; if (skb) { skb_trim(skb, 0); + if (likely(buffer_info->dma)) + goto write_desc; goto map_skb; }@@ -680,10 +682,12 @@ static void e1000_alloc_rx_buffers(struct e1000_ring *rx_ring, DMA_FROM_DEVICE); if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { dev_err(&pdev->dev, "Rx DMA map failed\n"); + buffer_info->dma = 0; adapter->rx_dma_failed++; break; } +write_desc: rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma);@@ -941,7 +945,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,dma_rmb(); /* read descriptor and
rx_buffer_infoafter status DD */ skb =buffer_info->skb;
-buffer_info->skb= NULL;
prefetch(skb->data - NET_IP_ALIGN);drivers/net/ethernet/intel/e1000e/netdev.c +0
-5@@ -955,9 +958,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done, cleaned = true; cleaned_count++; - dma_unmap_single(&pdev->dev, buffer_info->dma, - adapter->rx_buffer_len, DMA_FROM_DEVICE); - buffer_info->dma = 0; length = le16_to_cpu(rx_desc->wb.upper.length);@@ -973,8 +973,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done, if (adapter->flags2 & FLAG2_IS_DISCARDING) { /* All receives must fit into a single buffer */ e_dbg("Receive packet consumed multiple buffers\n"); - /* recycle */ - buffer_info->skb = skb; if (staterr & E1000_RXD_STAT_EOP) adapter->flags2 &= ~FLAG2_IS_DISCARDING; goto next_desc;@@ -982,8 +980,6 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,if (
unlikely((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) && !(netdev->features & NETIF_F_RXALL))) { - /* recycle */
-buffer_info->skb= skb;
gotonext_desc;
}drivers/net/ethernet/intel/e1000e/netdev.c +0
-0@@ -1010,19 +1006,35 @@ static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,struct
sk_buff*new_skb=napi_alloc_skb(&adapter->napi, length); if (new_skb) {
+ dma_sync_single_for_cpu(&pdev->dev,
+buffer_info->dma,
+adapter->rx_buffer_len,
+DMA_FROM_DEVICE);skb_copy_to_linear_data_offset(new_skb, -NET_IP_ALIGN, (skb->data - NET_IP_ALIGN), (length + NET_IP_ALIGN));
- /* save the skb inbuffer_infoas good */ -buffer_info->skb= skb;
+ dma_sync_single_for_device(&pdev->dev, +buffer_info->dma,
+adapter->rx_buffer_len, +DMA_FROM_DEVICE);
skb =new_skb;
}
/* else just continue with the old one */ }
- /* end copybreak code */
+
+ /* If skb was not replaced by copybreak, we are consuming + * the original buffer and must release the DMA mapping. + */
+ if (skb ==buffer_info->skb) {Quoted 8 lines
+
buffer_info->skb= NULL;
+ dma_unmap_single(&pdev->dev,buffer_info->dma, +adapter->rx_buffer_len,
+DMA_FROM_DEVICE);
+buffer_info->dma= 0;
+ }
skb_put(skb, length);
/* Receive Checksum Offload */Kind regards,
Paul