Skip to contentSkip to conversation

nvmem: core: Default to read-only if wp-gpios present

PATCH Superseded Marek Vasut 2 participants 2 messages Apr 27 – Apr 28

Subsystems (2)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 nvmem: core: Default to read-only if wp-gpios present

In case the nvmem DT node contains "wp-gpios" DT property, the device currently defaults to read-write and the force_ro sysfs attribute reads
0. Switch to the default read-only, which is both safer, and aligned with eMMC HW BOOT partition force_ro sysfs attribute behavior, which also defaults to read-only.

The adjustment of nvmem->read_only value to read-only in case wp-gpios DT property is present must be done only after the device_add() got called because device_add() does internally call nvmem_bin_attr_get_umode(), which configures the permissions of 'nvmem' bin attr based on the value of nvmem->read_only that is only parsed from DT property 'read-only', without any adjustment. This way, if DT property 'read-only' is present, the 'nvmem' attribute is always read-only. Otherwise, if the device is writeable, then 'nvmem' attribute is writeable, and nvmem->read_only defaults to read-only, but can be switched to read-write at runtime via the 'force_ro' attribute.

The updated behavior can be tested as follows:

Current content:
"

$ cat /sys/bus/nvmem/devices/logging7/force_ro
1
$ hexdump -C /sys/bus/nvmem/devices/logging7/nvmem
00000000  66 6f 6f 0a ff ff ff ff
"

Write into default-read-only device:
"

$ echo bar > /sys/bus/nvmem/devices/logging7/nvmem
bash: echo: write error: Operation not permitted
$ cat /sys/bus/nvmem/devices/logging7/force_ro
1
"

Unlock and write into device:
"

$ echo 0 > /sys/bus/nvmem/devices/logging7/force_ro
$ cat /sys/bus/nvmem/devices/logging7/force_ro
0
$ echo bar > /sys/bus/nvmem/devices/logging7/nvmem
$ hexdump -C /sys/bus/nvmem/devices/logging7/nvmem
00000000  62 61 72 0a ff ff ff ff
"

Relock and write into device, fails because device is read-only again:
"

$ echo 1 > /sys/bus/nvmem/devices/logging7/force_ro
$ echo baz > /sys/bus/nvmem/devices/logging7/nvmem
bash: echo: write error: Operation not permitted
$ hexdump -C /sys/bus/nvmem/devices/logging7/nvmem
00000000  62 61 72 0a ff ff ff ff
"

---
Cc: Arnd Bergmann <[email protected]>
Cc: Bartosz Golaszewski <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Srinivas Kandagatla <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
V2: Simplify the implementation, make devices with wp-gpios default
to read-only and let users unlock those devices via force_ro sysfs attribute, just like eMMC HW BOOT partitions
V3: Drop unnecessary gpiod_set_value_cansleep()

---
 drivers/nvmem/core.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/nvmem/core.c +4 -0
index 311cb2e5a5c02..be28a366f6031 100644
@@ -1019,6 +1019,10 @@ struct nvmem_device *nvmem_register(const struct nvmem_config *config)
 	if (rval)
 		goto err_remove_dev;
 
+	/* If the device has WP GPIO, default to read-only */
+	if (nvmem->wp_gpio)
+		nvmem->read_only = true;
+
 #ifdef CONFIG_NVMEM_SYSFS
 	rval = nvmem_populate_sysfs_cells(nvmem);
 	if (rval)
Signature · 1 line
2.53.0
Reviewed-by on v3 1/1
#1 lore raw
Quoted 6 lines · Marek Vasut

In case the nvmem DT node contains "wp-gpios" DT property, the device currently defaults to read-write and the force_ro sysfs attribute reads
0. Switch to the default read-only, which is both safer, and aligned with eMMC HW BOOT partition force_ro sysfs attribute behavior, which also defaults to read-only.

Quoted 10 lines

The adjustment of nvmem->read_only value to read-only in case wp-gpios DT property is present must be done only after the device_add() got called because device_add() does internally call nvmem_bin_attr_get_umode(), which configures the permissions of 'nvmem' bin attr based on the value of nvmem->read_only that is only parsed from DT property 'read-only', without any adjustment. This way, if DT property 'read-only' is present, the 'nvmem' attribute is always read-only. Otherwise, if the device is writeable, then 'nvmem' attribute is writeable, and nvmem->read_only defaults to read-only, but can be switched to read-write at runtime via the 'force_ro' attribute.

This slightly changes the behavior for user-space but I'm willing to give it a go and see if anyone complains.

Bart