Skip to contentSkip to conversation

sunxi: A523: Add SPI support

PATCH Superseded Andre Przywara 2 participants 12 messages May 11 – May 15

Subsystems (4)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

cover sunxi: A523: Add SPI support

This series adds SPI support to the A523 family of SoCs. The SPI controller is very similar to the previous generation, to a degree where we don't need actual code changes, but just to add the new DT compatible string to the driver (patch 1/5).
Patch 3/5 adds support for SPL SPI booting, again no real driver changes, just adding the required pinmux settings for the A523. To make this easier, patch 2/5 reworks the SPI pinmux setting. That doesn't look as pretty as I hoped for, but is still better than what we have now. The last two patches enable SPI and SPI booting on two boards with NOR flash.

I could successfully boot U-Boot from SPI on the Radxa A5E with that. The OrangePi 4A also has a NOR SPI, but I couldn't test this, as I don't have that board.

Please have a look and test!

Cheers,
Andre

Andre Przywara (5):
spi: sunxi: add support for A523 SPI controller
sunxi: spl: spi: Clean up SPI0 pinmux setting
sunxi: spl: spi: Add support for Allwinner A523
sunxi: configs: Radxa Cubie A5E: enable SPI
sunxi: configs: OrangePi 4A: enable SPI

 arch/arm/mach-sunxi/spl_spi_sunxi.c | 48 +++++++++++++----------------
 configs/orangepi_4a_defconfig       |  4 +++
 configs/radxa-cubie-a5e_defconfig   |  6 +++-
 drivers/spi/spi-sunxi.c             |  4 +++
 4 files changed, 35 insertions(+), 27 deletions(-)
Signature · 1 line
2.46.4
#1 lore raw

PATCH 1/5 spi: sunxi: add support for A523 SPI controller

The SPI controllers in the Allwinner A523/A527/T527 SoCs is very close to the one used in the R329 and D1 generation, definitely as far as our driver is concerned.

Add the new compatible string, but use the existing config section from the previous SoC generation.

---
 drivers/spi/spi-sunxi.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/spi/spi-sunxi.c +4 -0
index 08b603f04a2..4e91cf6b7fd 100644
@@ -587,6 +587,10 @@ static const struct udevice_id sun4i_spi_ids[] = {
 	  .compatible = "allwinner,sun50i-r329-spi",
 	  .data = (ulong)&sun50i_r329_spi_variant,
 	},
+	{
+	  .compatible = "allwinner,sun55i-a523-spi",
+	  .data = (ulong)&sun50i_r329_spi_variant,
+	},
 	{ /* sentinel */ }
 };
 
Signature · 1 line
2.46.4
maintainer Acked-by on v1 1/5
#2 lore raw

Re: [PATCH 1/5] spi: sunxi: add support for A523 SPI controller

Dne ponedeljek, 11. maj 2026 ob 23:37:09 Srednjeevropski poletni čas je Andre Przywara napisal(a):

Quoted 8 lines

The SPI controllers in the Allwinner A523/A527/T527 SoCs is very close to the one used in the R329 and D1 generation, definitely as far as our driver is concerned.

Add the new compatible string, but use the existing config section from the previous SoC generation.

Best regards,
Jernej

#3 lore raw

PATCH 2/5 sunxi: spl: spi: Clean up SPI0 pinmux setting

In reply to Andre Przywara

The function to set the pinmux for the Port C SPI0 pins was looking more like a logic puzzle from a magazine than something that readers could understand and extend.

Replace the convoluted pinmux setup, grouped by pin, with a simple array of the four pins involved, and just initialise this array at build time, based on the selected SoC.

This makes it easy to see which pins are needed, and even easier to extend.

---
 arch/arm/mach-sunxi/spl_spi_sunxi.c | 43 ++++++++++++-----------------
 1 file changed, 18 insertions(+), 25 deletions(-)
arch/arm/mach-sunxi/spl_spi_sunxi.c +18 -25
index 5f72e809952..905a7db2a77 100644
@@ -105,35 +105,28 @@
 
 /*
  * Allwinner A10/A20 SoCs were using pins PC0,PC1,PC2,PC23 for booting
- * from SPI Flash, everything else is using pins PC0,PC1,PC2,PC3.
- * The H6 uses PC0, PC2, PC3, PC5, the H616 PC0, PC2, PC3, PC4.
+ * from SPI Flash, later SoCs are using pins PC0,PC1,PC2,PC3.
+ * Newer SoCs are all over the place.
  */
 static void spi0_pinmux_setup(unsigned int pin_function)
 {
-	/* All chips use PC2. And all chips use PC0, except R528/T113 */
-	if (!IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(0), pin_function);
-
-	sunxi_gpio_set_cfgpin(SUNXI_GPC(2), pin_function);
+	const u16 spi0_pc_pins[4] = {
+#if IS_ENABLED(CONFIG_MACH_SUN8I_R528)
+		SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(4), SUNXI_GPC(5)
+#elif IS_ENABLED(CONFIG_MACH_SUN50I_H616)
+		SUNXI_GPC(0), SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(4)
+#elif IS_ENABLED(CONFIG_MACH_SUN50I_H6)
+		SUNXI_GPC(0), SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(5)
+#elif IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN5I) || \
+      IS_ENABLED(CONFIG_MACH_SUN7I) || IS_ENABLED(CONFIG_MACH_SUN8I_R40)
+		SUNXI_GPC(0), SUNXI_GPC(1), SUNXI_GPC(2), SUNXI_GPC(23)
+#else
+		SUNXI_GPC(0), SUNXI_GPC(1), SUNXI_GPC(2), SUNXI_GPC(3)
+#endif
+	};
 
-	/* All chips except H6/H616/R528/T113 use PC1. */
-	if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6) &&
-	    !IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(1), pin_function);
-
-	if (IS_ENABLED(CONFIG_MACH_SUN50I_H6) ||
-	    IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(5), pin_function);
-	if (IS_ENABLED(CONFIG_MACH_SUN50I_H616) ||
-	    IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(4), pin_function);
-
-	/* Older generations use PC23 for CS, newer ones use PC3. */
-	if (IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN7I) ||
-	    IS_ENABLED(CONFIG_MACH_SUN8I_R40))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(23), pin_function);
-	else
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(3), pin_function);
+	for (int i = 0; i < 4; i++)
+		sunxi_gpio_set_cfgpin(spi0_pc_pins[i], pin_function);
 }
 
 static bool is_sun6i_gen_spi(void)
Signature · 1 line
2.46.4
maintainer
#4 lore raw

Re: [PATCH 2/5] sunxi: spl: spi: Clean up SPI0 pinmux setting

Dne ponedeljek, 11. maj 2026 ob 23:37:10 Srednjeevropski poletni čas je Andre Przywara napisal(a):

Quoted 33 lines

The function to set the pinmux for the Port C SPI0 pins was looking more like a logic puzzle from a magazine than something that readers could understand and extend.

Replace the convoluted pinmux setup, grouped by pin, with a simple array of the four pins involved, and just initialise this array at build time, based on the selected SoC.

This makes it easy to see which pins are needed, and even easier to extend.

---
 arch/arm/mach-sunxi/spl_spi_sunxi.c | 43 ++++++++++++-----------------
 1 file changed, 18 insertions(+), 25 deletions(-)
arch/arm/mach-sunxi/spl_spi_sunxi.c +2 -5
index 5f72e809952..905a7db2a77 100644
@@ -105,35 +105,28 @@
 
 /*
  * Allwinner A10/A20 SoCs were using pins PC0,PC1,PC2,PC23 for booting
- * from SPI Flash, everything else is using pins PC0,PC1,PC2,PC3.
- * The H6 uses PC0, PC2, PC3, PC5, the H616 PC0, PC2, PC3, PC4.
+ * from SPI Flash, later SoCs are using pins PC0,PC1,PC2,PC3.
+ * Newer SoCs are all over the place.
  */
 static void spi0_pinmux_setup(unsigned int pin_function)
 {
-	/* All chips use PC2. And all chips use PC0, except R528/T113 */
-	if (!IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(0), pin_function);

arch/arm/mach-sunxi/spl_spi_sunxi.c line 120

Quoted 10 lines
arch/arm/mach-sunxi/spl_spi_sunxi.c +8 -2
-
-	sunxi_gpio_set_cfgpin(SUNXI_GPC(2), pin_function);
+	const u16 spi0_pc_pins[4] = {
+#if IS_ENABLED(CONFIG_MACH_SUN8I_R528)
+		SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(4), SUNXI_GPC(5)
+#elif IS_ENABLED(CONFIG_MACH_SUN50I_H616)
+		SUNXI_GPC(0), SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(4)
+#elif IS_ENABLED(CONFIG_MACH_SUN50I_H6)
+		SUNXI_GPC(0), SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(5)
+#elif IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN5I) || \

Are you sure about CONFIG_MACH_SUN5I? It seems to me that it should fall to PC3 pin. Also A13 datasheet confirms it.

Best regards,
Jernej

Quoted 31 lines
arch/arm/mach-sunxi/spl_spi_sunxi.c +8 -18
+      IS_ENABLED(CONFIG_MACH_SUN7I) || IS_ENABLED(CONFIG_MACH_SUN8I_R40)
+		SUNXI_GPC(0), SUNXI_GPC(1), SUNXI_GPC(2), SUNXI_GPC(23)
+#else
+		SUNXI_GPC(0), SUNXI_GPC(1), SUNXI_GPC(2), SUNXI_GPC(3)
+#endif
+	};
 
-	/* All chips except H6/H616/R528/T113 use PC1. */
-	if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6) &&
-	    !IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(1), pin_function);
-
-	if (IS_ENABLED(CONFIG_MACH_SUN50I_H6) ||
-	    IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(5), pin_function);
-	if (IS_ENABLED(CONFIG_MACH_SUN50I_H616) ||
-	    IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(4), pin_function);
-
-	/* Older generations use PC23 for CS, newer ones use PC3. */
-	if (IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN7I) ||
-	    IS_ENABLED(CONFIG_MACH_SUN8I_R40))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(23), pin_function);
-	else
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(3), pin_function);
+	for (int i = 0; i < 4; i++)
+		sunxi_gpio_set_cfgpin(spi0_pc_pins[i], pin_function);
 }
 
 static bool is_sun6i_gen_spi(void)
#5 lore raw

Re: [PATCH 2/5] sunxi: spl: spi: Clean up SPI0 pinmux setting

Quoted 39 lines · On Tue, 12 May 2026 19:37:06 +0200 Jernej Škrabec <[email protected]>…

Dne ponedeljek, 11. maj 2026 ob 23:37:10 Srednjeevropski poletni čas je Andre Przywara napisal(a):

Quoted 38 lines

The function to set the pinmux for the Port C SPI0 pins was looking more like a logic puzzle from a magazine than something that readers could understand and extend.

Replace the convoluted pinmux setup, grouped by pin, with a simple array of the four pins involved, and just initialise this array at build time, based on the selected SoC.

This makes it easy to see which pins are needed, and even easier to extend.

---
 arch/arm/mach-sunxi/spl_spi_sunxi.c | 43 ++++++++++++-----------------
 1 file changed, 18 insertions(+), 25 deletions(-)
arch/arm/mach-sunxi/spl_spi_sunxi.c +5 -7
index 5f72e809952..905a7db2a77 100644
@@ -105,35 +105,28 @@
 
 /*
  * Allwinner A10/A20 SoCs were using pins PC0,PC1,PC2,PC23 for booting
- * from SPI Flash, everything else is using pins PC0,PC1,PC2,PC3.
- * The H6 uses PC0, PC2, PC3, PC5, the H616 PC0, PC2, PC3, PC4.
+ * from SPI Flash, later SoCs are using pins PC0,PC1,PC2,PC3.
+ * Newer SoCs are all over the place.
  */
 static void spi0_pinmux_setup(unsigned int pin_function)
 {
-	/* All chips use PC2. And all chips use PC0, except R528/T113 */
-	if (!IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(0), pin_function);
-
-	sunxi_gpio_set_cfgpin(SUNXI_GPC(2), pin_function);
+	const u16 spi0_pc_pins[4] = {
+#if IS_ENABLED(CONFIG_MACH_SUN8I_R528)
+		SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(4), SUNXI_GPC(5)
Quoted 8 lines

arch/arm/mach-sunxi/spl_spi_sunxi.c line 120

Quoted 5 lines
arch/arm/mach-sunxi/spl_spi_sunxi.c +5 -0
+#elif IS_ENABLED(CONFIG_MACH_SUN50I_H616)
+		SUNXI_GPC(0), SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(4)
+#elif IS_ENABLED(CONFIG_MACH_SUN50I_H6)
+		SUNXI_GPC(0), SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(5)
+#elif IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN5I) || \  

Are you sure about CONFIG_MACH_SUN5I? It seems to me that it should fall to PC3 pin. Also A13 datasheet confirms it.

Yes, you are right, good catch, will fix that!

Thanks for having a look!

Cheers,
Andre

Quoted 39 lines

Best regards,
Jernej

Quoted 31 lines
arch/arm/mach-sunxi/spl_spi_sunxi.c +8 -18
+      IS_ENABLED(CONFIG_MACH_SUN7I) || IS_ENABLED(CONFIG_MACH_SUN8I_R40)
+		SUNXI_GPC(0), SUNXI_GPC(1), SUNXI_GPC(2), SUNXI_GPC(23)
+#else
+		SUNXI_GPC(0), SUNXI_GPC(1), SUNXI_GPC(2), SUNXI_GPC(3)
+#endif
+	};
 
-	/* All chips except H6/H616/R528/T113 use PC1. */
-	if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6) &&
-	    !IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(1), pin_function);
-
-	if (IS_ENABLED(CONFIG_MACH_SUN50I_H6) ||
-	    IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(5), pin_function);
-	if (IS_ENABLED(CONFIG_MACH_SUN50I_H616) ||
-	    IS_ENABLED(CONFIG_MACH_SUN8I_R528))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(4), pin_function);
-
-	/* Older generations use PC23 for CS, newer ones use PC3. */
-	if (IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN7I) ||
-	    IS_ENABLED(CONFIG_MACH_SUN8I_R40))
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(23), pin_function);
-	else
-		sunxi_gpio_set_cfgpin(SUNXI_GPC(3), pin_function);
+	for (int i = 0; i < 4; i++)
+		sunxi_gpio_set_cfgpin(spi0_pc_pins[i], pin_function);
 }
 
 static bool is_sun6i_gen_spi(void)
#6 lore raw

PATCH 3/5 sunxi: spl: spi: Add support for Allwinner A523

In reply to Andre Przywara

The SPI IP in the Allwinner A523 is mostly compatible to the later generation used in other Allwinner SoCs, at least as far as the SPL driver is concerned.

Just add the pinmux configuration for SPI0 on PortC, as used by the BROM. This enables SPI (NOR) boot on A523/A527/T527 boards.

---
 arch/arm/mach-sunxi/spl_spi_sunxi.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
arch/arm/mach-sunxi/spl_spi_sunxi.c +4 -1
index 905a7db2a77..25878026891 100644
@@ -113,6 +113,8 @@ static void spi0_pinmux_setup(unsigned int pin_function)
 	const u16 spi0_pc_pins[4] = {
 #if IS_ENABLED(CONFIG_MACH_SUN8I_R528)
 		SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(4), SUNXI_GPC(5)
+#elif IS_ENABLED(CONFIG_MACH_SUN55I_A523)
+		SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(4), SUNXI_GPC(12)
 #elif IS_ENABLED(CONFIG_MACH_SUN50I_H616)
 		SUNXI_GPC(0), SUNXI_GPC(2), SUNXI_GPC(3), SUNXI_GPC(4)
 #elif IS_ENABLED(CONFIG_MACH_SUN50I_H6)
@@ -250,7 +252,8 @@ static void spi0_init(void)
 	unsigned int pin_function = SUNXI_GPC_SPI0;
 
 	if (IS_ENABLED(CONFIG_MACH_SUN50I) ||
-	    IS_ENABLED(CONFIG_SUN50I_GEN_H6))
+	    IS_ENABLED(CONFIG_SUN50I_GEN_H6) ||
+	    IS_ENABLED(CONFIG_MACH_SUN55I_A523))
 		pin_function = SUN50I_GPC_SPI0;
 	else if (IS_ENABLED(CONFIG_MACH_SUNIV) ||
 		 IS_ENABLED(CONFIG_MACH_SUN8I_R528))
Signature · 1 line
2.46.4
maintainer Reviewed-by on v1 3/5
#7 lore raw

Re: [PATCH 3/5] sunxi: spl: spi: Add support for Allwinner A523

Dne ponedeljek, 11. maj 2026 ob 23:37:11 Srednjeevropski poletni čas je Andre Przywara napisal(a):

Quoted 8 lines

The SPI IP in the Allwinner A523 is mostly compatible to the later generation used in other Allwinner SoCs, at least as far as the SPL driver is concerned.

Just add the pinmux configuration for SPI0 on PortC, as used by the BROM. This enables SPI (NOR) boot on A523/A527/T527 boards.

Best regards,
Jernej

#8 lore raw

PATCH 4/5 sunxi: configs: Radxa Cubie A5E: enable SPI

In reply to Andre Przywara

The Radxa Cubie A5E ships with SPI NOR flash, so enable the SPI and flash drivers, also the SPL version, for SPI booting.

Sync the defconfig file with the version from savedefconfig on the way.

---
 configs/radxa-cubie-a5e_defconfig | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
configs/radxa-cubie-a5e_defconfig +5 -1
index 84bc4e3d4a9..2a66d0e0866 100644
@@ -15,6 +15,7 @@ CONFIG_DRAM_SUNXI_TPR12=0x3533302f
 CONFIG_MACH_SUN55I_A523=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_R_I2C_ENABLE=y
+CONFIG_SPL_SPI_SUNXI=y
 CONFIG_SPL_SUNXI_LED_STATUS=y
 CONFIG_SPL_SUNXI_LED_STATUS_GPIO=356
 # CONFIG_SPL_SUNXI_LED_STATUS_ACTIVE_HIGH is not set
@@ -25,11 +26,14 @@ CONFIG_SYS_I2C_MVTWSI=y
 CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
 CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_PHY_REALTEK=y
+CONFIG_MTD=y
+CONFIG_SPI_FLASH_WINBOND=y
 CONFIG_SUN8I_EMAC=y
+CONFIG_PHY_REALTEK=y
 CONFIG_REGULATOR_AXP=y
 CONFIG_AXP717_POWER=y
 CONFIG_AXP_DCDC2_VOLT=920
 CONFIG_AXP_DCDC3_VOLT=1100
+CONFIG_SPI=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
Signature · 1 line
2.46.4
maintainer Acked-by on v1 4/5
#9 lore raw

Re: [PATCH 4/5] sunxi: configs: Radxa Cubie A5E: enable SPI

Dne ponedeljek, 11. maj 2026 ob 23:37:12 Srednjeevropski poletni čas je Andre Przywara napisal(a):

Quoted 6 lines

The Radxa Cubie A5E ships with SPI NOR flash, so enable the SPI and flash drivers, also the SPL version, for SPI booting.

Sync the defconfig file with the version from savedefconfig on the way.

Best regards,
Jernej

#10 lore raw

PATCH 5/5 sunxi: configs: OrangePi 4A: enable SPI

In reply to Andre Przywara

The OrangePi 4A board ships with SPI NOR flash, so enable the SPI and flash drivers, also the SPL version, for SPI booting.

---
 configs/orangepi_4a_defconfig | 4 ++++
 1 file changed, 4 insertions(+)
configs/orangepi_4a_defconfig +4 -0
index 6a44dd97959..2d36757ba11 100644
@@ -16,6 +16,7 @@ CONFIG_DRAM_SUNXI_TPR12=0x3a373233
 CONFIG_MACH_SUN55I_A523=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_R_I2C_ENABLE=y
+CONFIG_SPL_SPI_SUNXI=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 CONFIG_SPL_I2C=y
 CONFIG_SPL_SYS_I2C_LEGACY=y
@@ -23,10 +24,13 @@ CONFIG_SYS_I2C_MVTWSI=y
 CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
 CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_MTD=y
+CONFIG_SPI_FLASH_XMC=y
 CONFIG_REGULATOR_AXP=y
 CONFIG_AXP717_POWER=y
 CONFIG_AXP_I2C_ADDRESS=0x35
 CONFIG_AXP_DCDC2_VOLT=920
 CONFIG_AXP_DCDC3_VOLT=1160
+CONFIG_SPI=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
Signature · 1 line
2.46.4
maintainer Acked-by on v1 5/5
#11 lore raw

Re: [PATCH 5/5] sunxi: configs: OrangePi 4A: enable SPI

Dne ponedeljek, 11. maj 2026 ob 23:37:13 Srednjeevropski poletni čas je Andre Przywara napisal(a):

Quoted 4 lines

The OrangePi 4A board ships with SPI NOR flash, so enable the SPI and flash drivers, also the SPL version, for SPI booting.

Best regards,
Jernej