board: rockchip: Add for 9Tripod X3568 v4
Subsystems (2)
PATCH 1/1 board: rockchip: Add for 9Tripod X3568 v4
The 9Tripod X3568 v4 is an RK3568-based SBC, just like the RK3568-EVB. It always uses soldered connections between the X3568CV2/X3568CV3/X3568CV4 core board and the X3568bv4 I/O board.
The differences between the core boards
- PCB size, layout
- CPU (RKK3568B2/RK3568J)
- Memory type (DDR4/LPDDR4/LPDDR4X) and size
- eMMC size
- DSI/EDP resistor values
Although the components vary, they maintain full compatibility.
The X3568 board has multiple hardware revisions, and we currently support v4 (I/O board).
Specification:
- SoC: RockChip RK3568 ARM64 (4 cores)
- eMMC: 16-128 GB
- RAM: 2-16 GB
- Power: DC 12V 2A
- Ethernet: 2x YT8521SC RGMII (10/100/1000 Mbps)
- Wireless radio: 802.11b/g/n/ac/ax dual-band
- LED:
Power: AlwaysOn
User: GPIO
- Button:
VOL+: SARADC/0 <35k µV>
VOL-: SARADC/0 <450k µV>
Power/Reset: PMIC RK809
- CAN
CAN/1: 4-pin (PH 2.0)
- PWM
PWM/4: Backlight DSI/0 DSI/1
PWM/7: IR Receiver [may not install]
- UART:
UART/2: Debug TTL - 1500000 8N1 (1.25mm)
UART/3: TTL (PH 2.0)
UART/4: TTL (PH 2.0)
UART/8: AP6275S Bluetooth
UART/9: TTL (PH 2.0)
- I2C:
I2C/0: PMIC RK809
I2C/1: Touchscreen DSI/0 DSI/1
I2C/4: Camera
I2C/5: RTC@51 PCF8563
- I2S:
I2S/0: miniHDMI Sound
I2S/1: RK809 Audio Codec
I2S/3: AP6275S Bluetooth Sound
- SDMMC:
SDMMC/0: microSD (TF) slot
SDMMC/2: AP6275S SDIO WiFi card
- Camera: 1x CSI
- Video: miniHDMI / DSI0 (MIPI/LVDS) / DSI1 (MIPI/EDP)
- Audio: miniHDMI / MIC on-board / Speaker / SPDIF / 3.5mm Headphones / AP6275S Bluetooth
- USB:
USB 2.0 HOST x2
USB 2.0 HOST x3 (4-pin)
USB 2.0 OTG x1 (shared with USB 3.0 OTG/HOST) [slot may not install]
USB 3.0 HOST x1
USB 3.0 OTG/HOST x1
- SATA: 1x SATA 3.0 with Power/4-pin [slot may not install]
- PCIe: 1x PCIe 3.0 x2 (x4 connecter) [power/clock/slot may not install]
Link:
- https://appletsapi.52solution.com/media/X3568V4%E5%BC%80%E5%8F%91%E6%9D%BF%E7%A1%AC%E4%BB%B6%E6%89%8B%E5%86%8C.pdf
- https://blog.gov.cooking/archives/research-ninetripod-x3568-v4-and-flash.html
--- .../dts/rk3568-9tripod-x3568-v4-u-boot.dtsi | 3 + board/rockchip/evb_rk3568/MAINTAINERS | 7 ++ configs/9tripod-x3568-v4-rk3568_defconfig | 80 +++++++++++++++++++ doc/board/rockchip/rockchip.rst | 1 + 4 files changed, 91 insertions(+) create mode 100644 arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi create mode 100644 configs/9tripod-x3568-v4-rk3568_defconfig
arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi new file +3 -0
@@ -0,0 +1,3 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +#include "rk3568-u-boot.dtsi"
board/rockchip/evb_rk3568/MAINTAINERS +7 -0
@@ -1,3 +1,10 @@ +9TRIPOD-X3568-V4 +M: Coia Prant <[email protected]> +R: Jonas Karlman <[email protected]> +S: Maintained +F: configs/9tripod-x3568-v4-rk3568_defconfig +F: arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi + BANANAPI-BPI-R2-PRO M: Frank Wunderlich <[email protected]> S: Maintained
configs/9tripod-x3568-v4-rk3568_defconfig new file +80 -0
80 lines not on this page · raw message
doc/board/rockchip/rockchip.rst +1 -0
@@ -126,6 +126,7 @@ List of mainline supported Rockchip boards: - Xunlong Orange Pi 3B (orangepi-3b-rk3566) * rk3568 + - 9Tripod X3568 v4 (9tripod-x3568-v4-rk3568) - Rockchip Evb-RK3568 (evb-rk3568) - Banana Pi BPI-R2 Pro (bpi-r2-pro-rk3568) - EmbedFire LubanCat 2 (lubancat-2-rk3568)
Signature · 1 line
2.53.0
Hi Coia,
Quoted 85 lines · Coia Prant
[You don't often get email from [email protected]. Learn why this is important at https://aka.ms/LearnAboutSenderIdentification ]
The 9Tripod X3568 v4 is an RK3568-based SBC, just like the RK3568-EVB. It always uses soldered connections between the X3568CV2/X3568CV3/X3568CV4 core board and the X3568bv4 I/O board.
The differences between the core boards
- PCB size, layout
- CPU (RKK3568B2/RK3568J)
- Memory type (DDR4/LPDDR4/LPDDR4X) and size
- eMMC size
- DSI/EDP resistor values
Although the components vary, they maintain full compatibility.The X3568 board has multiple hardware revisions, and we currently support v4 (I/O board).
Specification:
- SoC: RockChip RK3568 ARM64 (4 cores)
- eMMC: 16-128 GB
- RAM: 2-16 GB
- Power: DC 12V 2A
- Ethernet: 2x YT8521SC RGMII (10/100/1000 Mbps)
- Wireless radio: 802.11b/g/n/ac/ax dual-band
- LED:
Power: AlwaysOn
User: GPIO
- Button:VOL+: SARADC/0 <35k µV> VOL-: SARADC/0 <450k µV> Power/Reset: PMIC RK809- CAN
CAN/1: 4-pin (PH 2.0)
- PWM
PWM/4: Backlight DSI/0 DSI/1
PWM/7: IR Receiver [may not install]
- UART:UART/2: Debug TTL - 1500000 8N1 (1.25mm) UART/3: TTL (PH 2.0) UART/4: TTL (PH 2.0) UART/8: AP6275S Bluetooth UART/9: TTL (PH 2.0) - I2C: I2C/0: PMIC RK809 I2C/1: Touchscreen DSI/0 DSI/1 I2C/4: Camera I2C/5: RTC@51 PCF8563 - I2S: I2S/0: miniHDMI Sound I2S/1: RK809 Audio Codec I2S/3: AP6275S Bluetooth Sound- SDMMC:
SDMMC/0: microSD (TF) slot
SDMMC/2: AP6275S SDIO WiFi card
- Camera: 1x CSI
- Video: miniHDMI / DSI0 (MIPI/LVDS) / DSI1 (MIPI/EDP)
- Audio: miniHDMI / MIC on-board / Speaker / SPDIF / 3.5mm Headphones / AP6275S Bluetooth
- USB:USB 2.0 HOST x2 USB 2.0 HOST x3 (4-pin) USB 2.0 OTG x1 (shared with USB 3.0 OTG/HOST) [slot may not install] USB 3.0 HOST x1 USB 3.0 OTG/HOST x1- SATA: 1x SATA 3.0 with Power/4-pin [slot may not install]
- PCIe: 1x PCIe 3.0 x2 (x4 connecter) [power/clock/slot may not install]Link:
- https://appletsapi.52solution.com/media/X3568V4%E5%BC%80%E5%8F%91%E6%9D%BF%E7%A1%AC%E4%BB%B6%E6%89%8B%E5%86%8C.pdf
- https://blog.gov.cooking/archives/research-ninetripod-x3568-v4-and-flash.htmlSigned-off-by Coia Prant <[email protected]>--- .../dts/rk3568-9tripod-x3568-v4-u-boot.dtsi | 3 + board/rockchip/evb_rk3568/MAINTAINERS | 7 ++ configs/9tripod-x3568-v4-rk3568_defconfig | 80 +++++++++++++++++++ doc/board/rockchip/rockchip.rst | 1 + 4 files changed, 91 insertions(+)create mode 100644
arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsicreate mode 100644 configs/9tripod-x3568-v4-rk3568_defconfigarch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi new file +0
-0
arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi line 3
Quoted 3 lines
arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi new file +3
-0@@ -0,0 +1,3 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +#include "rk3568-u-boot.dtsi"
This file is not necessary as if rk3568-9tripod-x3568-v4-u-boot.dtsi is not present, rk3568-u-boot.dtsi will be included automatically (due to CONFIG_SYS_SOC being "rk3568").
board/rockchip/evb_rk3568/MAINTAINERS line 3
Quoted 8 lines
board/rockchip/evb_rk3568/MAINTAINERS +3
-0@@ -1,3 +1,10 @@ +9TRIPOD-X3568-V4 +M: Coia Prant <[email protected]> +R: Jonas Karlman <[email protected]>
I'm not sure Jonas has agreed to do this so please drop him from the Reviewer, except if he publicly asks you to.
board/rockchip/evb_rk3568/MAINTAINERS line 7
Quoted 4 lines
board/rockchip/evb_rk3568/MAINTAINERS +4
-0+S: Maintained +F: configs/9tripod-x3568-v4-rk3568_defconfig +F: arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi +
Since you can remove the file, this line can also be removed.
Quoted 38 lines
board/rockchip/evb_rk3568/MAINTAINERS +0
-0BANANAPI-BPI-R2-PRO M: Frank Wunderlich <[email protected]> S: Maintainedconfigs/9tripod-x3568-v4-rk3568_defconfig new file +29
-0@@ -0,0 +1,80 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_SYS_HAS_NONCACHED_MEMORY=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_DEFAULT_DEVICE_TREE="rockchip/rk3568-9tripod-x3568-v4" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_SERIAL=y +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_PCI=y +CONFIG_DEBUG_UART=y +CONFIG_AHCI=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-9tripod-x3568-v4.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y
configs/9tripod-x3568-v4-rk3568_defconfig line 39
Quoted 10 lines
configs/9tripod-x3568-v4-rk3568_defconfig new file +10
-0+CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_USB=y +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +# CONFIG_OF_UPSTREAM is not set +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
Any reason for removing clock-names from xPL DTB?
Looks ok to me otherwise.
Cheers,
Quentin
Quoted 163 lines · Quentin Schulz
Hi Coia,
Quoted 85 lines · Coia Prant
[You don't often get email from [email protected]. Learn why this is important at https://aka.ms/LearnAboutSenderIdentification ]
The 9Tripod X3568 v4 is an RK3568-based SBC, just like the RK3568-EVB. It always uses soldered connections between the X3568CV2/X3568CV3/X3568CV4 core board and the X3568bv4 I/O board.
The differences between the core boards
- PCB size, layout
- CPU (RKK3568B2/RK3568J)
- Memory type (DDR4/LPDDR4/LPDDR4X) and size
- eMMC size
- DSI/EDP resistor values
Although the components vary, they maintain full compatibility.The X3568 board has multiple hardware revisions, and we currently support v4 (I/O board).
Specification:
- SoC: RockChip RK3568 ARM64 (4 cores)
- eMMC: 16-128 GB
- RAM: 2-16 GB
- Power: DC 12V 2A
- Ethernet: 2x YT8521SC RGMII (10/100/1000 Mbps)
- Wireless radio: 802.11b/g/n/ac/ax dual-band
- LED:
Power: AlwaysOn
User: GPIO
- Button:VOL+: SARADC/0 <35k µV> VOL-: SARADC/0 <450k µV> Power/Reset: PMIC RK809- CAN
CAN/1: 4-pin (PH 2.0)
- PWM
PWM/4: Backlight DSI/0 DSI/1
PWM/7: IR Receiver [may not install]
- UART:UART/2: Debug TTL - 1500000 8N1 (1.25mm) UART/3: TTL (PH 2.0) UART/4: TTL (PH 2.0) UART/8: AP6275S Bluetooth UART/9: TTL (PH 2.0) - I2C: I2C/0: PMIC RK809 I2C/1: Touchscreen DSI/0 DSI/1 I2C/4: Camera I2C/5: RTC@51 PCF8563 - I2S: I2S/0: miniHDMI Sound I2S/1: RK809 Audio Codec I2S/3: AP6275S Bluetooth Sound- SDMMC:
SDMMC/0: microSD (TF) slot
SDMMC/2: AP6275S SDIO WiFi card
- Camera: 1x CSI
- Video: miniHDMI / DSI0 (MIPI/LVDS) / DSI1 (MIPI/EDP)
- Audio: miniHDMI / MIC on-board / Speaker / SPDIF / 3.5mm Headphones / AP6275S Bluetooth
- USB:USB 2.0 HOST x2 USB 2.0 HOST x3 (4-pin) USB 2.0 OTG x1 (shared with USB 3.0 OTG/HOST) [slot may not install] USB 3.0 HOST x1 USB 3.0 OTG/HOST x1- SATA: 1x SATA 3.0 with Power/4-pin [slot may not install]
- PCIe: 1x PCIe 3.0 x2 (x4 connecter) [power/clock/slot may not install]Link:
- https://appletsapi.52solution.com/media/X3568V4%E5%BC%80%E5%8F%91%E6%9D%BF%E7%A1%AC%E4%BB%B6%E6%89%8B%E5%86%8C.pdf
- https://blog.gov.cooking/archives/research-ninetripod-x3568-v4-and-flash.htmlSigned-off-by Coia Prant <[email protected]>--- .../dts/rk3568-9tripod-x3568-v4-u-boot.dtsi | 3 + board/rockchip/evb_rk3568/MAINTAINERS | 7 ++ configs/9tripod-x3568-v4-rk3568_defconfig | 80 +++++++++++++++++++ doc/board/rockchip/rockchip.rst | 1 + 4 files changed, 91 insertions(+)create mode 100644
arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsicreate mode 100644 configs/9tripod-x3568-v4-rk3568_defconfigarch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi new file +0
-0arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi line 3
Quoted 3 lines
arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi new file +3
-0@@ -0,0 +1,3 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +#include "rk3568-u-boot.dtsi"This file is not necessary as if
rk3568-9tripod-x3568-v4-u-boot.dtsiis not present,rk3568-u-boot.dtsiwill be included automatically (due toCONFIG_SYS_SOCbeing "rk3568").board/rockchip/evb_rk3568/MAINTAINERS line 3
Quoted 8 lines
board/rockchip/evb_rk3568/MAINTAINERS +3
-0@@ -1,3 +1,10 @@ +9TRIPOD-X3568-V4 +M: Coia Prant <[email protected]> +R: Jonas Karlman <[email protected]>I'm not sure Jonas has agreed to do this so please drop him from the Reviewer, except if he publicly asks you to.
board/rockchip/evb_rk3568/MAINTAINERS line 7
Quoted 4 lines
board/rockchip/evb_rk3568/MAINTAINERS +4
-0+S: Maintained +F: configs/9tripod-x3568-v4-rk3568_defconfig +F: arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi +Since you can remove the file, this line can also be removed.
Quoted 38 lines
board/rockchip/evb_rk3568/MAINTAINERS +0
-0BANANAPI-BPI-R2-PRO M: Frank Wunderlich <[email protected]> S: Maintainedconfigs/9tripod-x3568-v4-rk3568_defconfig new file +29
-0@@ -0,0 +1,80 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_SYS_HAS_NONCACHED_MEMORY=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_DEFAULT_DEVICE_TREE="rockchip/rk3568-9tripod-x3568-v4" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_SERIAL=y +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_PCI=y +CONFIG_DEBUG_UART=y +CONFIG_AHCI=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-9tripod-x3568-v4.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=yconfigs/9tripod-x3568-v4-rk3568_defconfig line 39
Quoted 10 lines
configs/9tripod-x3568-v4-rk3568_defconfig new file +10
-0+CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_USB=y +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +# CONFIG_OF_UPSTREAM is not set +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"Any reason for removing clock-names from xPL DTB?
Quoted 4 lines
Looks ok to me otherwise.
Cheers,
Quentin
Hi Quentin,
Thanks for review, this is the first time I've submitted a patch to u-boot.
I referred to some other rk3568 boards that had the clock name removed, so I left it as it was. There was no problem with the board starting, and I don't know why them remove clocks name.
The board is working fine.
Best,
Coia
Hi Coia,
Quoted 166 lines · Coia Prant
[You don't often get email from [email protected]. Learn why this is important at https://aka.ms/LearnAboutSenderIdentification ]
Quoted 163 lines · Quentin Schulz
Hi Coia,
Quoted 85 lines · Coia Prant
[You don't often get email from [email protected]. Learn why this is important at https://aka.ms/LearnAboutSenderIdentification ]
The 9Tripod X3568 v4 is an RK3568-based SBC, just like the RK3568-EVB. It always uses soldered connections between the X3568CV2/X3568CV3/X3568CV4 core board and the X3568bv4 I/O board.
The differences between the core boards
- PCB size, layout
- CPU (RKK3568B2/RK3568J)
- Memory type (DDR4/LPDDR4/LPDDR4X) and size
- eMMC size
- DSI/EDP resistor values
Although the components vary, they maintain full compatibility.The X3568 board has multiple hardware revisions, and we currently support v4 (I/O board).
Specification:
- SoC: RockChip RK3568 ARM64 (4 cores)
- eMMC: 16-128 GB
- RAM: 2-16 GB
- Power: DC 12V 2A
- Ethernet: 2x YT8521SC RGMII (10/100/1000 Mbps)
- Wireless radio: 802.11b/g/n/ac/ax dual-band
- LED:
Power: AlwaysOn
User: GPIO
- Button:VOL+: SARADC/0 <35k µV> VOL-: SARADC/0 <450k µV> Power/Reset: PMIC RK809 - CAN CAN/1: 4-pin (PH 2.0)- PWM
PWM/4: Backlight DSI/0 DSI/1
PWM/7: IR Receiver [may not install]
- UART:UART/2: Debug TTL - 1500000 8N1 (1.25mm) UART/3: TTL (PH 2.0) UART/4: TTL (PH 2.0) UART/8: AP6275S Bluetooth UART/9: TTL (PH 2.0) - I2C: I2C/0: PMIC RK809 I2C/1: Touchscreen DSI/0 DSI/1 I2C/4: Camera I2C/5: RTC@51 PCF8563 - I2S: I2S/0: miniHDMI Sound I2S/1: RK809 Audio Codec I2S/3: AP6275S Bluetooth Sound- SDMMC:
SDMMC/0: microSD (TF) slot
SDMMC/2: AP6275S SDIO WiFi card
- Camera: 1x CSI
- Video: miniHDMI / DSI0 (MIPI/LVDS) / DSI1 (MIPI/EDP)
- Audio: miniHDMI / MIC on-board / Speaker / SPDIF / 3.5mm Headphones / AP6275S Bluetooth
- USB:USB 2.0 HOST x2 USB 2.0 HOST x3 (4-pin) USB 2.0 OTG x1 (shared with USB 3.0 OTG/HOST) [slot may not install] USB 3.0 HOST x1 USB 3.0 OTG/HOST x1- SATA: 1x SATA 3.0 with Power/4-pin [slot may not install]
- PCIe: 1x PCIe 3.0 x2 (x4 connecter) [power/clock/slot may not install]Link:
- https://appletsapi.52solution.com/media/X3568V4%E5%BC%80%E5%8F%91%E6%9D%BF%E7%A1%AC%E4%BB%B6%E6%89%8B%E5%86%8C.pdf
- https://blog.gov.cooking/archives/research-ninetripod-x3568-v4-and-flash.htmlSigned-off-by Coia Prant <[email protected]>--- .../dts/rk3568-9tripod-x3568-v4-u-boot.dtsi | 3 + board/rockchip/evb_rk3568/MAINTAINERS | 7 ++ configs/9tripod-x3568-v4-rk3568_defconfig | 80 +++++++++++++++++++ doc/board/rockchip/rockchip.rst | 1 + 4 files changed, 91 insertions(+)create mode 100644
arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsicreate mode 100644 configs/9tripod-x3568-v4-rk3568_defconfigarch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi new file +0
-0arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi line 3
Quoted 3 lines
arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi new file +3
-0@@ -0,0 +1,3 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +#include "rk3568-u-boot.dtsi"This file is not necessary as if
rk3568-9tripod-x3568-v4-u-boot.dtsiis not present,rk3568-u-boot.dtsiwill be included automatically (due toCONFIG_SYS_SOCbeing "rk3568").board/rockchip/evb_rk3568/MAINTAINERS line 3
Quoted 8 lines
board/rockchip/evb_rk3568/MAINTAINERS +3
-0@@ -1,3 +1,10 @@ +9TRIPOD-X3568-V4 +M: Coia Prant <[email protected]> +R: Jonas Karlman <[email protected]>I'm not sure Jonas has agreed to do this so please drop him from the Reviewer, except if he publicly asks you to.
board/rockchip/evb_rk3568/MAINTAINERS line 7
Quoted 4 lines
board/rockchip/evb_rk3568/MAINTAINERS +4
-0+S: Maintained +F: configs/9tripod-x3568-v4-rk3568_defconfig +F: arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi +Since you can remove the file, this line can also be removed.
Quoted 38 lines
board/rockchip/evb_rk3568/MAINTAINERS +0
-0BANANAPI-BPI-R2-PRO M: Frank Wunderlich <[email protected]> S: Maintainedconfigs/9tripod-x3568-v4-rk3568_defconfig new file +29
-0@@ -0,0 +1,80 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_SYS_HAS_NONCACHED_MEMORY=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_DEFAULT_DEVICE_TREE="rockchip/rk3568-9tripod-x3568-v4" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_SERIAL=y +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_PCI=y +CONFIG_DEBUG_UART=y +CONFIG_AHCI=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-9tripod-x3568-v4.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=yconfigs/9tripod-x3568-v4-rk3568_defconfig line 39
Quoted 10 lines
configs/9tripod-x3568-v4-rk3568_defconfig new file +10
-0+CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_USB=y +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +# CONFIG_OF_UPSTREAM is not set +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"Any reason for removing clock-names from xPL DTB?
Quoted 9 lines
Quoted 4 lines
Looks ok to me otherwise.
Cheers,
QuentinHi Quentin,
Thanks for review, this is the first time I've submitted a patch to u-boot.
Welcome to the community :) !
Quoted 2 lines
I referred to some other rk3568 boards that had the clock name removed, so I left it as it was. There was no problem with the board starting, and I don't know why them remove clocks name.
Yeah I guessed, it's what most people do but I don't think it should have made it in the first place for other boards, at least not without an explanation (maybe we need to fix a bug somewhere else such that we don't need to remove it in xPL stages?).
Quoted 2 lines
The board is working fine.
If you remove clock-names from CONFIG_OF_SPL_REMOVE_PROPS?
Cheers,
Quentin
Quoted 186 lines · Quentin Schulz
Hi Coia,
Quoted 166 lines · Coia Prant
[You don't often get email from [email protected]. Learn why this is important at https://aka.ms/LearnAboutSenderIdentification ]
Quoted 163 lines · Quentin Schulz
Hi Coia,
Quoted 85 lines · Coia Prant
[You don't often get email from [email protected]. Learn why this is important at https://aka.ms/LearnAboutSenderIdentification ]
The 9Tripod X3568 v4 is an RK3568-based SBC, just like the RK3568-EVB. It always uses soldered connections between the X3568CV2/X3568CV3/X3568CV4 core board and the X3568bv4 I/O board.
The differences between the core boards
- PCB size, layout
- CPU (RKK3568B2/RK3568J)
- Memory type (DDR4/LPDDR4/LPDDR4X) and size
- eMMC size
- DSI/EDP resistor values
Although the components vary, they maintain full compatibility.The X3568 board has multiple hardware revisions, and we currently support v4 (I/O board).
Specification:
- SoC: RockChip RK3568 ARM64 (4 cores)
- eMMC: 16-128 GB
- RAM: 2-16 GB
- Power: DC 12V 2A
- Ethernet: 2x YT8521SC RGMII (10/100/1000 Mbps)
- Wireless radio: 802.11b/g/n/ac/ax dual-band
- LED:
Power: AlwaysOn
User: GPIO
- Button:VOL+: SARADC/0 <35k µV> VOL-: SARADC/0 <450k µV> Power/Reset: PMIC RK809 - CAN CAN/1: 4-pin (PH 2.0)- PWM
PWM/4: Backlight DSI/0 DSI/1
PWM/7: IR Receiver [may not install]
- UART:UART/2: Debug TTL - 1500000 8N1 (1.25mm) UART/3: TTL (PH 2.0) UART/4: TTL (PH 2.0) UART/8: AP6275S Bluetooth UART/9: TTL (PH 2.0) - I2C: I2C/0: PMIC RK809 I2C/1: Touchscreen DSI/0 DSI/1 I2C/4: Camera I2C/5: RTC@51 PCF8563 - I2S: I2S/0: miniHDMI Sound I2S/1: RK809 Audio Codec I2S/3: AP6275S Bluetooth Sound- SDMMC:
SDMMC/0: microSD (TF) slot
SDMMC/2: AP6275S SDIO WiFi card
- Camera: 1x CSI
- Video: miniHDMI / DSI0 (MIPI/LVDS) / DSI1 (MIPI/EDP)
- Audio: miniHDMI / MIC on-board / Speaker / SPDIF / 3.5mm Headphones / AP6275S Bluetooth
- USB:USB 2.0 HOST x2 USB 2.0 HOST x3 (4-pin) USB 2.0 OTG x1 (shared with USB 3.0 OTG/HOST) [slot may not install] USB 3.0 HOST x1 USB 3.0 OTG/HOST x1- SATA: 1x SATA 3.0 with Power/4-pin [slot may not install]
- PCIe: 1x PCIe 3.0 x2 (x4 connecter) [power/clock/slot may not install]Link:
- https://appletsapi.52solution.com/media/X3568V4%E5%BC%80%E5%8F%91%E6%9D%BF%E7%A1%AC%E4%BB%B6%E6%89%8B%E5%86%8C.pdf
- https://blog.gov.cooking/archives/research-ninetripod-x3568-v4-and-flash.htmlSigned-off-by Coia Prant <[email protected]>--- .../dts/rk3568-9tripod-x3568-v4-u-boot.dtsi | 3 + board/rockchip/evb_rk3568/MAINTAINERS | 7 ++ configs/9tripod-x3568-v4-rk3568_defconfig | 80 +++++++++++++++++++ doc/board/rockchip/rockchip.rst | 1 + 4 files changed, 91 insertions(+)create mode 100644
arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsicreate mode 100644 configs/9tripod-x3568-v4-rk3568_defconfigarch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi new file +0
-0arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi line 3
Quoted 3 lines
arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi new file +3
-0@@ -0,0 +1,3 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +#include "rk3568-u-boot.dtsi"This file is not necessary as if
rk3568-9tripod-x3568-v4-u-boot.dtsiis not present,rk3568-u-boot.dtsiwill be included automatically (due toCONFIG_SYS_SOCbeing "rk3568").board/rockchip/evb_rk3568/MAINTAINERS line 3
Quoted 8 lines
board/rockchip/evb_rk3568/MAINTAINERS +3
-0@@ -1,3 +1,10 @@ +9TRIPOD-X3568-V4 +M: Coia Prant <[email protected]> +R: Jonas Karlman <[email protected]>I'm not sure Jonas has agreed to do this so please drop him from the Reviewer, except if he publicly asks you to.
board/rockchip/evb_rk3568/MAINTAINERS line 7
Quoted 4 lines
board/rockchip/evb_rk3568/MAINTAINERS +4
-0+S: Maintained +F: configs/9tripod-x3568-v4-rk3568_defconfig +F: arch/arm/dts/rk3568-9tripod-x3568-v4-u-boot.dtsi +Since you can remove the file, this line can also be removed.
Quoted 38 lines
board/rockchip/evb_rk3568/MAINTAINERS +0
-0BANANAPI-BPI-R2-PRO M: Frank Wunderlich <[email protected]> S: Maintainedconfigs/9tripod-x3568-v4-rk3568_defconfig new file +29
-0@@ -0,0 +1,80 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_SYS_HAS_NONCACHED_MEMORY=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_DEFAULT_DEVICE_TREE="rockchip/rk3568-9tripod-x3568-v4" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_SERIAL=y +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_PCI=y +CONFIG_DEBUG_UART=y +CONFIG_AHCI=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-9tripod-x3568-v4.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=yconfigs/9tripod-x3568-v4-rk3568_defconfig line 39
Quoted 10 lines
configs/9tripod-x3568-v4-rk3568_defconfig new file +10
-0+CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_USB=y +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +# CONFIG_OF_UPSTREAM is not set +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"Any reason for removing clock-names from xPL DTB?
Quoted 9 lines
Quoted 4 lines
Looks ok to me otherwise.
Cheers,
QuentinHi Quentin,
Thanks for review, this is the first time I've submitted a patch to u-boot.
Welcome to the community :) !
Quoted 2 lines
I referred to some other rk3568 boards that had the clock name removed, so I left it as it was. There was no problem with the board starting, and I don't know why them remove clocks name.
Yeah I guessed, it's what most people do but I don't think it should have made it in the first place for other boards, at least not without an explanation (maybe we need to fix a bug somewhere else such that we don't need to remove it in xPL stages?).
Quoted 7 lines
Quoted 2 lines
The board is working fine.
If you remove clock-names from
CONFIG_OF_SPL_REMOVE_PROPS?Cheers,
Quentin
Hi Quentin,
I have tested you said, after remove it. It still works fine.
I will post PATCH v2 later.
Thanks.
Best,
Coia