Skip to contentSkip to conversation

arm64: dts: rockchip: Fix rk3399-roc-pc-plus analog audio

PATCH Applied Fabio Estevam 3 participants 6 messages Jul 17 – Jul 29

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/3 arm64: dts: rockchip: Fix rk3399-roc-pc-plus analog audio

From: Fabio Estevam <[email protected]>

The ES8388 sound card on the rk3399-roc-pc-plus fails to probe because i2s1 cannot claim its MCLK pin:

pinctrl: pin gpio4-0 already requested by ff880000.i2s; cannot claim for ff890000.i2s
pinctrl: error -EINVAL: pin-128 (ff890000.i2s)
pinctrl: error -EINVAL: could not request pin 128 (gpio4-0) from group i2s-8ch-mclk-pin on device rockchip-pinctrl

GPIO4_A0 is routed as SCLK_I2S_8CH_OUT and is used by i2s1 as the external MCLK for the ES8388 codec. The board dts already removes GPIO4_A0 from the i2s0_8ch_bus pin group, but i2s0 still claims the same pin through its bclk_off state.

Since the i2s driver requests both states, this blocks i2s1 pinctrl setup and leaves the simple-audio-card deferred with a parse error.

Override i2s0_8ch_bus_bclk_off as well, matching the existing i2s0_8ch_bus override, so GPIO4_A0 is left for i2s1/ES8388 audio.

Fixes 6d9a7bd6a13c ("arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS")
---
 arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)
arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts +12 -0
index 4f2831097624..f6d62ee51f1b 100644
@@ -136,6 +136,18 @@ &i2s0_8ch_bus {
 		<3 RK_PD7 1 &pcfg_pull_none>;
 };
 
+&i2s0_8ch_bus_bclk_off {
+	rockchip,pins =
+		<3 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>,
+		<3 RK_PD1 1 &pcfg_pull_none>,
+		<3 RK_PD2 1 &pcfg_pull_none>,
+		<3 RK_PD3 1 &pcfg_pull_none>,
+		<3 RK_PD4 1 &pcfg_pull_none>,
+		<3 RK_PD5 1 &pcfg_pull_none>,
+		<3 RK_PD6 1 &pcfg_pull_none>,
+		<3 RK_PD7 1 &pcfg_pull_none>;
+};
+
 &i2s1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2s_8ch_mclk_pin>, <&i2s1_2ch_bus>;
Signature · 1 line
2.43.0
#1 lore raw

PATCH 2/3 arm64: dts: rockchip: Enable wireless on rk3399-roc-pc-plus

From: Fabio Estevam <[email protected]>

The rk3399-roc-pc-plus board has an Ampak AP6256 Wi-Fi/Bluetooth module.

Describe the Wi-Fi function on SDIO0 and the Bluetooth function on UART0. Add the Bluetooth wake and shutdown pinctrl entries, enable SDIO0 as a non-removable SDIO device, and add the power sequencing delays needed by the module.

The module uses the RK808 CLKOUT2 output as its 32 kHz low-power clock. Drop the duplicate HYM8563 clock-output-names property and remove the same clock from the SDIO power sequencer so the Bluetooth node can request the shared LPO clock directly.

---
 .../boot/dts/rockchip/rk3399-roc-pc-plus.dts  | 51 +++++++++++++++++++
 1 file changed, 51 insertions(+)
arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts +51 -0
index f6d62ee51f1b..f87bc7b6afc1 100644
@@ -123,6 +123,10 @@ es8388: es8388@11 {
 	};
 };
 
+&hym8563 {
+	/delete-property/ clock-output-names;
+};
+
 /* <4 RK_PA0 1 &pcfg_pull_none> is used as i2s_8ch_mclk_pin */
 &i2s0_8ch_bus {
 	rockchip,pins =
@@ -157,6 +161,20 @@ &i2s1 {
 };
 
 &pinctrl {
+	bt {
+		bt_enable_h: bt-enable-h {
+			rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_host_wake_l: bt-host-wake-l {
+			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_wake_l: bt-wake-l {
+			rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	es8388 {
 		ear_ctl_pin: ear-ctl-pin {
 			rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_output_high>;
@@ -180,6 +198,28 @@ i2s_8ch_mclk_pin: i2s-8ch-mclk-pin {
 	};
 };
 
+&sdio_pwrseq {
+	/delete-property/ clocks;
+	/delete-property/ clock-names;
+	post-power-on-delay-ms = <100>;
+	power-off-delay-us = <500000>;
+};
+
+&sdio0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
 &u2phy0 {
 	status = "okay";
 
@@ -212,6 +252,17 @@ &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rk808 1>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio2 RK_PD2 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+	};
 };
 
 &usbdrd_dwc3_0 {
Signature · 1 line
2.43.0
#3 lore raw

PATCH 3/3 arm64: dts: rockchip: Keep rk3399-roc-pc-plus work LED on

In reply to Fabio Estevam

From: Fabio Estevam <[email protected]>

The rk3399-roc-pc-plus inherits the work LED heartbeat trigger from the common rk3399-roc-pc.dtsi.

On the rk3399-roc-pc-plus this LED is the prominent blue front-panel status LED. Blinking it continuously is distracting for a PC-style board. The usual default is a steady power/status indication while the system is running.

Use the default-on trigger for this board instead. This keeps the LED useful as a simple running indicator and still lets userspace select a different trigger or turn it off after boot.

---
 arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts +4 -0
index f87bc7b6afc1..7e8039b19be7 100644
@@ -93,6 +93,10 @@ leds {
 	};
 };
 
+&work_led {
+	linux,default-trigger = "default-on";
+};
+
 &fusb0 {
 	vbus-supply = <&vcc_vbus_typec1>;
 };
Signature · 1 line
2.43.0
#4 lore raw

Re: [PATCH 3/3] arm64: dts: rockchip: Keep rk3399-roc-pc-plus work LED on

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider: - [Medium] The commit message describes the work LED as a "prominent blue front-panel status LED", but the…

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] The commit message describes the work LED as a "prominent blue front-panel status LED", but the patch fails to override the inherited "green:work" label, resulting in a code and commit message mismatch. --

--- Patch [3]: [PATCH 3/3] arm64: dts: rockchip: Keep rk3399-roc-pc-plus work LED on --- commit 7bd9a09829c15f03ac88e155bb13da9235dada8c
Author: Fabio Estevam <[email protected]>

arm64: dts: rockchip: Keep rk3399-roc-pc-plus work LED on

This commit overrides the default LED trigger for the rk3399-roc-pc-plus work LED to default-on. It changes the behavior from a distracting continuous blink to a steady status indication.

arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts leds { · line 98

Quoted 11 lines
arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts +3 -0
index f87bc7b6afc14..7e8039b19be7e 100644
@@ -93,6 +93,10 @@ leds {
 	};
 };
 
+&work_led {
+	linux,default-trigger = "default-on";
+};

[Severity: Medium]
The commit message mentions this is the prominent blue front-panel status LED. Since the board inherits from rk3399-roc-pc.dtsi where the work LED is typically configured with the green:work label, does this node also need a color or label override?

If the inherited label is not overridden here, the sysfs interface might misrepresent the physical blue LED as green, causing a mismatch between the commit message's description and the resulting device tree.

Quoted 4 lines
arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts +1 -0
+
 &fusb0 {
 	vbus-supply = <&vcc_vbus_typec1>;
 };
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=3
#2 lore raw

Re: [PATCH 2/3] arm64: dts: rockchip: Enable wireless on rk3399-roc-pc-plus

In reply to Fabio Estevam
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider: - [High] Removing the shared 32kHz LPO clock from the SDIO power sequencer breaks Wi-Fi initialization when…

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [High] Removing the shared 32kHz LPO clock from the SDIO power sequencer breaks Wi-Fi initialization when Bluetooth is disabled or probes later. --

--- Patch [2]: [PATCH 2/3] arm64: dts: rockchip: Enable wireless on rk3399-roc-pc-plus --- commit d6496a6030e5f440c56fb715094eff4f9078ed81
Author: Fabio Estevam <[email protected]>

arm64: dts: rockchip: Enable wireless on rk3399-roc-pc-plus

This commit enables the Ampak AP6256 Wi-Fi/Bluetooth module on the rk3399-roc-pc-plus board. It describes the SDIO and UART interfaces, adds power sequencing delays, and removes the clock from the SDIO power sequencer to allow the Bluetooth node to request it directly.

Quoted 4 lines
arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts +0 -0
index f6d62ee51f1b9..f87bc7b6afc14 100644

[ ... ]

arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts i2s_8ch_mclk_pin: i2s-8ch-mclk-pin { · line 203

Quoted 7 lines
arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts +3 -0
@@ -180,6 +198,28 @@ i2s_8ch_mclk_pin: i2s-8ch-mclk-pin {
 	};
 };
 
+&sdio_pwrseq {
+	/delete-property/ clocks;
+	/delete-property/ clock-names;

[Severity: High]
Will removing the shared 32kHz LPO clock from the SDIO power sequencer break Wi-Fi initialization when Bluetooth is disabled or probes later?

If the MMC/SDIO subsystem initiates its power-on sequence before the Bluetooth driver probes, or if Bluetooth is disabled, the LPO clock will not be enabled. Without this clock, the Wi-Fi module cannot start its state machine and will fail to respond to the initial CMD5 enumeration from the MMC core.

Additionally, if Bluetooth enters runtime suspend and gates the clock, could this crash the active Wi-Fi firmware?

Quoted 3 lines
arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts +3 -0
+	post-power-on-delay-ms = <100>;
+	power-off-delay-us = <500000>;
+};
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=2
maintainer Applied
#5 lore raw
In reply to Fabio Estevam
Quoted 9 lines · Fabio Estevam

The ES8388 sound card on the rk3399-roc-pc-plus fails to probe because i2s1 cannot claim its MCLK pin:

pinctrl: pin gpio4-0 already requested by ff880000.i2s; cannot claim for ff890000.i2s
pinctrl: error -EINVAL: pin-128 (ff890000.i2s)
pinctrl: error -EINVAL: could not request pin 128 (gpio4-0) from group i2s-8ch-mclk-pin on device rockchip-pinctrl

[...]

Applied, thanks!

[1/3] arm64: dts: rockchip: Fix rk3399-roc-pc-plus analog audio

      commit: 4f7259ebe1eba4778768a4f5a0bbbe439d10f3f3
[2/3] arm64: dts: rockchip: Enable wireless on rk3399-roc-pc-plus
      commit: 2dfc88c13fb2db7f17c55f16b679cdfe4ded19c5
[3/3] arm64: dts: rockchip: Keep rk3399-roc-pc-plus work LED on
      commit: b2007873ddfff223bb680c7ff60eaf675670f07a

Best regards,

Signature · 1 line
Heiko Stuebner <[email protected]>