RFC: Pine64 Pinetab-V dts Device Tree File
RFC PATCH 1/1 RFC: Pine64 Pinetab-V dts Device Tree File
Added compilable PineTab-V device-tree dts file derived from pine64 community distributed dts and additional parameters Community provided definitions:
- Audio Codec
- Accelerometer
Additional parameters include:
- Definitions for sd-card and on board EMMC devices
- Definitins for power supply to sd-card
---
Provide support for the Pine64 Pinetab-V Risc-V 64bit Tablet
--- .../src/riscv/starfive/jh7110-pine64-pinetabv.dts | 116 +++++++++++++++++++++ 1 file changed, 116 insertions(+)
dts/upstream/src/riscv/starfive/jh7110-pine64-pinetabv.dts new file +116 -0
@@ -0,0 +1,116 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2026 T Anoduck <[email protected]> + * Through the Graces of: E Shattow <[email protected]> + * REV-DATE: July 18, 2026 + */ + +/dts-v1/; +#include "jh7110-common.dtsi" + +/ { + compatible = "pine64,pinetabv", "starfive,jh7110"; + model = "Pine64 PinetabV"; + + soc { + i2c@10030000 { + compatible = "snps,designware-i2c"; + reg = <0x00 0x10030000 0x00 0x10000>; + clocks = <0x03 0x8a>; + clock-names = "ref"; + resets = <0x03 0x4c>; + interrupts = <0x23>; + #address-cells = <0x01>; + #size-cells = <0x00>; + status = "okay"; + clock-frequency = <0x186a0>; + i2c-sda-hold-time-ns = <0x12c>; + i2c-sda-falling-time-ns = <0x1fe>; + i2c-scl-falling-time-ns = <0x1fe>; + pinctrl-names = "default"; + pinctrl-0 = <0x17>; + + audio-codec@11 { + compatible = "everest,es8316"; + reg = <0x11>; + clocks = <0x18>; + clock-names = "mclk"; + #sound-dai-cells = <0x00>; + papower-gpio = <0x19 0x32 0x00>; + hp-det-gpio = <0x19 0x24 0x00>; + phandle = <0x64>; + }; + + accelerometer@18 { + compatible = "silan,sc7a20"; + reg = <0x18>; + mount-matrix = "0", "0", "-1", "1", "0", "0", "0", "-1", "0"; + }; + }; + sd_vcc: sd-vcc { + compatible = "regulator-fixed"; + regulator-name = "sd_vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <0x19 0x23 0x00>; + enable-active-low; + regulator-boot-on; + regulator-always-on; + }; + + mmc@16010000 { + compatible = "starfive,jh7110-mmc"; + reg = <0x00 0x16010000 0x00 0x10000>; + clocks = <0x03 0x5b 0x03 0x5d>; + clock-names = "biu", "ciu"; + resets = <0x03 0x40>; + reset-names = "reset"; + interrupts = <0x4a>; + fifo-depth = <0x20>; + fifo-watermark-aligned; + data-addr = <0x00>; + starfive,sysreg = <0x1f 0x14 0x1a 0x7c000000>; + status = "okay"; + max-frequency = <0x5f5e100>; + assigned-clocks = <0x03 0x5d>; + vmmc-supply = <&sd_vcc>; + assigned-clock-rates = <0x2faf080>; + bus-width = <0x08>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + non-removable; + cap-mmc-hw-reset; + post-power-on-delay-ms = <0xc8>; + pinctrl-names = "default"; + pinctrl-0 = <0x3c>; + vqmmc-supply = <&sd_vcc>; + }; + + mmc@16020000 { + compatible = "starfive,jh7110-mmc"; + reg = <0x00 0x16020000 0x00 0x10000>; + clocks = <0x03 0x5c 0x03 0x5e>; + clock-names = "biu", "ciu"; + resets = <0x03 0x41>; + reset-names = "reset"; + interrupts = <0x4b>; + fifo-depth = <0x20>; + fifo-watermark-aligned; + data-addr = <0x00>; + starfive,sysreg = <0x1f 0x9c 0x01 0x3e>; + status = "okay"; + max-frequency = <0x5f5e100>; + assigned-clocks = <0x03 0x5e>; + assigned-clock-rates = <0x2faf080>; + bus-width = <0x04>; + no-sdio; + no-mmc; + cd-gpios = <0x19 0x29 0x01>; + cap-sd-highspeed; + post-power-on-delay-ms = <0xc8>; + pinctrl-names = "default"; + pinctrl-0 = <0x3e>; + }; + }; +};
---
base-commit: 605d72111224172381a2a94d734183222d5b8952
change-id: 20260718-develop-1e9fbc9b4fe0
Best regards,
Signature · 1 line
anoduck <[email protected]>
Quoted 9 lines · anoduck
Added compilable PineTab-V device-tree dts file derived from pine64 community distributed dts and additional parameters Community provided definitions:
- Audio Codec
- AccelerometerAdditional parameters include:
- Definitions for sd-card and on board EMMC devices
- Definitins for power supply to sd-card
Quoted 8 lines
Signed-off-by The Anoduck <[email protected]>---
Provide support for the Pine64 Pinetab-V Risc-V 64bit TabletSigned-off-by anoduck <[email protected]>--- .../src/riscv/starfive/jh7110-pine64-pinetabv.dts | 116 +++++++++++++++++++++ 1 file changed, 116 insertions(+)
So per the documentation at
https://docs.u-boot-project.org/en/latest/develop/devicetree/control.html#resyncing-with-devicetree-rebasing
we only take modifications in dts/upstream that are strict cherry-pick's from the upstream source. This needs to be done under arch/riscv/ instead, and you should split the additional changes in to a -u-boot.dtsi suffixed file, so that it's easier to replace this with the upstream file when ready. Thanks.
Signature · 1 line
Tom