hwmon: (lm63) Clamp PWM frequency multiplier to [1, 31]
Guenter Roeck
maintainerPATCH 1/1 hwmon: (lm63) Clamp PWM frequency multiplier to [1, 31]
Sashiko is concerned that reading a PWM frequency multiplier outside the supported range of [1, 31] might result in bad PWM values written to the chip. Technically, the chip should never return a value with the upper 3 bits set, so this should never happen. However, it is unknown if there are LM63 variants where the upper bits of the register can be written.
Clamp the PWM frequency multiplier value to [1, 31] when reading it from the chip to avoid the problem.
--- drivers/hwmon/lm63.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-)
drivers/hwmon/lm63.c +3 -4
@@ -32,6 +32,7 @@#include <linux/hwmon-sysfs.h> #include <linux/hwmon.h> #include <linux/err.h> +#include <linux/minmax.h> #include <linux/mutex.h> #include <linux/of.h> #include <linux/sysfs.h>
@@ -249,8 +250,7 @@ static struct lm63_data *lm63_update_device(struct device *dev) data->pwm1_freq =i2c_smbus_read_byte_data (client,LM63_REG_PWM_FREQ ); -if (data->pwm1_freq ==0 ) - data->pwm1_freq =1 ; + data->pwm1_freq =clamp (data->pwm1_freq,1 ,31 ); data->pwm1[0 ] =i2c_smbus_read_byte_data (client,LM63_REG_PWM_VALUE );
@@ -1188,8 +1188,7 @@ static void lm63_init_client(struct lm63_data *data)/* We may need pwm1_freq before ever updating the client data */ data->pwm1_freq =i2c_smbus_read_byte_data (client,LM63_REG_PWM_FREQ ); -if (data->pwm1_freq ==0 ) - data->pwm1_freq =1 ; + data->pwm1_freq =clamp (data->pwm1_freq,1 ,31 );switch (data->kind) {case lm63:
Signature · 1 line
2.45.2
[email protected]
AI reviewThank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider: - [High] Using clamp() instead of masking incorrectly handles reserved bits, potentially corrupting the PWM…
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [High] Using clamp() instead of masking incorrectly handles reserved bits, potentially corrupting the PWM frequency multiplier. --
--- Patch [1]: [PATCH] hwmon: (lm63) Clamp PWM frequency multiplier to [1, 31] --- commit 7a1685b6b2f22a4e89624bbad02ad4ecbb43a849
Author: Guenter Roeck <[email protected]>
hwmon: (lm63) Clamp PWM frequency multiplier to [1, 31]
This commit updates the lm63 driver to clamp the PWM frequency multiplier read from the chip to the range [1, 31]. This is intended to prevent writing bad PWM values if the upper bits of the register are unexpectedly set on some variants.
Quoted 3 lines
drivers/hwmon/lm63.c +0
-0
[ ... ]
drivers/hwmon/lm63.c static struct lm63_data *lm63_update_device(struct device *dev) · line 253
Quoted 7 lines
drivers/hwmon/lm63.c +1
-2@@ -249,8 +250,7 @@ static struct lm63_data *lm63_update_device(struct device *dev) data->pwm1_freq =i2c_smbus_read_byte_data (client,LM63_REG_PWM_FREQ ); -if (data->pwm1_freq ==0 ) - data->pwm1_freq =1 ; + data->pwm1_freq =clamp (data->pwm1_freq,1 ,31 );
[Severity: High]
If the upper bits of the LM63_REG_PWM_FREQ register happen to be set on some LM63 variants, won't clamp() treat the entire byte as a magnitude?
For example, if the register reads 0x81, clamp(129, 1, 31) will evaluate to 31, rather than isolating the lower 5-bit multiplier of 1.
Would it be more correct to mask out the reserved bits with & 0x1F before checking for zero or clamping?
Quoted 3 lines
drivers/hwmon/lm63.c +0
-0data->pwm1[0 ] =i2c_smbus_read_byte_data (client,LM63_REG_PWM_VALUE );
[ ... ]
drivers/hwmon/lm63.c static void lm63_init_client(struct lm63_data *data) · line 1191
Quoted 7 lines
drivers/hwmon/lm63.c +1
-2@@ -1188,8 +1188,7 @@ static void lm63_init_client(struct lm63_data *data)/* We may need pwm1_freq before ever updating the client data */ data->pwm1_freq =i2c_smbus_read_byte_data (client,LM63_REG_PWM_FREQ ); -if (data->pwm1_freq ==0 ) - data->pwm1_freq =1 ; + data->pwm1_freq =clamp (data->pwm1_freq,1 ,31 );
[Severity: High]
Does this have the same risk as lm63_update_device() above, where reserved upper bits being set will cause the multiplier to be incorrectly calculated and clamped to 31?
Quoted 3 lines
drivers/hwmon/lm63.c +0
-0switch (data->kind) {case lm63:
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=1