dt-bindings: sound: Convert TI DA830 EVM audio to DT schema
Subsystems (3)
PATCH 1/1 dt-bindings: sound: Convert TI DA830 EVM audio to DT schema
Convert the Texas Instruments DA830 EVM audio complex bindings to DT schema.
--- .../bindings/sound/davinci-evm-audio.txt | 49 ----------- .../bindings/sound/ti,da830-evm-audio.yaml | 83 +++++++++++++++++++ 2 files changed, 83 insertions(+), 49 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/davinci-evm-audio.txt create mode 100644 Documentation/devicetree/bindings/sound/ti,da830-evm-audio.yaml
Documentation/devicetree/bindings/sound/davinci-evm-audio.txt deleted +0 -49
@@ -1,49 +0,0 @@ -* Texas Instruments SoC audio setups with TLV320AIC3X Codec - -Required properties: -- compatible : "ti,da830-evm-audio" : forDM365/DA8xx/OMAPL1x/AM33xx -- ti,model : The user-visible name of this sound complex. -- ti,audio-codec : The phandle of the TLV320AIC3x audio codec -- ti,mcasp-controller : The phandle of the McASP controller -- ti,audio-routing : A list of the connections between audio components. - Each entry is a pair of strings, the first being the connection's sink, - the second being the connection's source. Valid names for sources and - sinks are the codec's pins, and the jacks on the board: - -Optional properties: -- ti,codec-clock-rate : The Codec Clock rate (in Hz) applied to the Codec. -- clocks : Reference to the master clock -- clock-names : The clock should be named "mclk" -- Either codec-clock-rate or the codec-clock reference has to be defined. If - the both are defined the driver attempts to set referenced clock to the - defined rate and takes the rate from the clock reference. - - Board connectors: - - * Headphone Jack - * Line Out - * Mic Jack - * Line In - - -Example: - -sound { - compatible = "ti,da830-evm-audio"; - ti,model = "DA830 EVM"; - ti,audio-codec = <&tlv320aic3x>; - ti,mcasp-controller = <&mcasp1>; - ti,codec-clock-rate = <12000000>; - ti,audio-routing = - "Headphone Jack", "HPLOUT", - "Headphone Jack", "HPROUT", - "Line Out", "LLOUT", - "Line Out", "RLOUT", - "MIC3L", "Mic Bias 2V", - "MIC3R", "Mic Bias 2V", - "Mic Bias 2V", "Mic Jack", - "LINE1L", "Line In", - "LINE2L", "Line In", - "LINE1R", "Line In", - "LINE2R", "Line In"; -};
Documentation/devicetree/bindings/sound/ti,da830-evm-audio.yaml new file +83 -0
83 lines not on this page · raw message
Signature · 1 line
2.43.0
Mark Brown
maintainerQuoted 2 lines · Eduard Bostina
Convert the Texas Instruments DA830 EVM audio complex bindings to DT schema.
Please submit patches using subject lines reflecting the style for the subsystem, this makes it easier for people to identify relevant patches. Look at what existing commits in the area you're changing are doing and make sure your subject lines visually resemble what they're doing. There's no need to resubmit to fix this alone.
Quoted 11 lines · Eduard Bostina
Convert the Texas Instruments DA830 EVM audio complex bindings to DT schema.
Signed-off-by Eduard Bostina <[email protected]>--- .../bindings/sound/davinci-evm-audio.txt | 49 ----------- .../bindings/sound/ti,da830-evm-audio.yaml | 83 +++++++++++++++++++ 2 files changed, 83 insertions(+), 49 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/davinci-evm-audio.txt create mode 100644 Documentation/devicetree/bindings/sound/ti,da830-evm-audio.yaml
Mark Brown
maintainerQuoted 1 line · Eduard Bostina
dt-bindings: sound: Convert TI DA830 EVM audio to DT schema
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-7.4
Thanks!
[1/1] dt-bindings: sound: Convert TI DA830 EVM audio to DT schema
https://git.kernel.org/broonie/sound/c/b0ac345bad82
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark