spi: spi-qpic-snand: publish the ECC context to snandc->qspi
Subsystems (3)
PATCH 1/1 spi: spi-qpic-snand: publish the ECC context to snandc->qspi
qcom_spi_ooblayout_ecc() and qcom_spi_ooblayout_free() read the ECC configuration through snandc->qspi->ecc. qcom_spi_probe() points it at a zeroed scratch struct and only qcom_spi_ecc_prepare_io_req_pipelined(), which runs on page I/O, ever updates it. qcom_spi_ecc_init_ctx_pipelined() installs the ooblayout but does not publish the context it just allocated, and qcom_spi_ecc_cleanup_ctx_pipelined() frees that context without clearing the pointer.
spinand_init() calls mtd_ooblayout_count_freebytes() right after the ECC context is created and before any page I/O, so the ooblayout always runs against a pointer that does not describe the current context:
- On a first probe it reads the zeroed struct from qcom_spi_probe(), so steps, bytes and bbm_size are 0. The count then returns 0 rather than an error, so the probe continues with mtd->oobavail set to 0.
- On a probe retry it reads the ecc_cfg the previous attempt freed.
A retry is easy to hit. On IPQ5018 with the qcom,smem-part parser the partition parse returns -EPROBE_DEFER until SMEM has probed, so the first spi-nand probe defers. It defers inside mtd_device_parse_register(), after mtd_otp_nvmem_add() has already read the factory OTP - that read goes through prepare_io_req and leaves snandc->qspi->ecc pointing at the context that spinand_cleanup() then frees. The second probe allocates a new context, never publishes it, and computes the OOB layout from the freed one. Once the slab has been reused, qecc->steps holds garbage and
oobregion->length = qecc->steps * 4;
goes negative. qcom_spi_ooblayout_free() only reports -ERANGE for section 1 and later, so mtd_ooblayout_count_bytes() sums the regions and returns that negative length as the byte count. The -512 below is steps * 4 with steps == -128. It is a byte count that happens to collide with -ERESTARTSYS, not an error the driver returned. spinand_init() takes it as an error, and because it is not -EPROBE_DEFER the driver core never retries and the NAND never appears:
spi-nand spi0.0: ESMT SPI NAND was found.
spi-nand spi0.0: probe with driver spi-nand failed with error -512 UBI error: cannot open mtd rootfs, error -2
Waiting for root device /dev/ubiblock0_1...
On a Mercusys MR80X (IPQ5018, ESMT F50D1G41LB) about half of the boots failed to mount the rootfs, the outcome depending on whether the freed memory had been overwritten yet.
Publish the context when it is created and clear the pointer when it is destroyed. Clearing leaves snandc->qspi->ecc NULL after cleanup, which is safe: the mtd is unregistered before cleanup_ctx runs, so no ooblayout callback can follow.
---
Tested on a Mercusys MR80X (IPQ5018, ESMT F50D1G41LB) running 6.18.44 with the equivalent change; mainline build-tested with W=1, no warnings.
drivers/spi/spi-qpic-snand.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/spi/spi-qpic-snand.c +3 -0
@@ -411,6 +411,8 @@ static int qcom_spi_ecc_init_ctx_pipelined(struct nand_device *nand)dev_dbg (snandc->dev,"ECC strength: %u bits per %u bytes\n" , ecc_cfg->strength, ecc_cfg->step_size); + snandc->qspi->ecc = ecc_cfg; +return 0 ; err_free_ecc_cfg:
@@ -427,6 +429,7 @@ static void qcom_spi_ecc_cleanup_ctx_pipelined(struct nand_device *nand)kfree (snandc->qspi->oob_buf); snandc->qspi->oob_buf =NULL ; + snandc->qspi->ecc =NULL ;kfree (ecc_cfg); }
Signature · 1 line
2.55.0
Quoted 9 lines · Johan Alvarado
qcom_spi_ooblayout_ecc()andqcom_spi_ooblayout_free()read the ECC configuration throughsnandc->qspi->ecc.qcom_spi_probe()points it at a zeroed scratch struct and onlyqcom_spi_ecc_prepare_io_req_pipelined(), which runs on page I/O, ever updates it.qcom_spi_ecc_init_ctx_pipelined()installs the ooblayout but does not publish the context it just allocated, andqcom_spi_ecc_cleanup_ctx_pipelined()frees that context without clearing the pointer.[...]
Applied to mtd/fixes, thanks!
[1/1] spi: spi-qpic-snand: publish the ECC context to snandc->qspi
commit: 93bc7c4d2f4198586a6dbd7797c3bbf1ca845761
Patche(s) should be available on mtd/linux.git and will be part of the next PR (provided that no robot complains by then).
Kind regards,
Miquèl
Mark Brown
maintainerQuoted 6 lines · Miquel Raynal
Quoted 2 lines · Johan Alvarado
qcom_spi_ooblayout_ecc()andqcom_spi_ooblayout_free()read the ECC configuration throughsnandc->qspi->ecc.qcom_spi_probe()points it at a[1/1] spi: spi-qpic-snand: publish the ECC context to
snandc->qspicommit: 93bc7c4d2f4198586a6dbd7797c3bbf1ca845761
Oh?
Miquel Raynal
maintainerQuoted 9 lines · Mark Brown
Quoted 6 lines · Miquel Raynal
Quoted 2 lines · Johan Alvarado
qcom_spi_ooblayout_ecc()andqcom_spi_ooblayout_free()read the ECC configuration throughsnandc->qspi->ecc.qcom_spi_probe()points it at a[1/1] spi: spi-qpic-snand: publish the ECC context to
snandc->qspicommit: 93bc7c4d2f4198586a6dbd7797c3bbf1ca845761Oh?
-ETOOMANYKEYWORDS ._.
Dropped, my bad :)
Mark Brown
maintainerQuoted 10 lines · Miquel Raynal
Quoted 4 lines · Mark Brown
Quoted 2 lines
[1/1] spi: spi-qpic-snand: publish the ECC context to
snandc->qspicommit: 93bc7c4d2f4198586a6dbd7797c3bbf1ca845761Oh?
-ETOOMANYKEYWORDS._.Dropped, my bad :)
Ah, OK!
Hi Johan,
2026. 08. 25. 3:38 keltezéssel, Johan Alvarado írta:
Quoted 52 lines
qcom_spi_ooblayout_ecc()andqcom_spi_ooblayout_free()read the ECC configuration throughsnandc->qspi->ecc.qcom_spi_probe()points it at a zeroed scratch struct and onlyqcom_spi_ecc_prepare_io_req_pipelined(), which runs on page I/O, ever updates it.qcom_spi_ecc_init_ctx_pipelined()installs the ooblayout but does not publish the context it just allocated, andqcom_spi_ecc_cleanup_ctx_pipelined()frees that context without clearing the pointer.
spinand_init()callsmtd_ooblayout_count_freebytes()right after the ECC context is created and before any page I/O, so the ooblayout always runs against a pointer that does not describe the current context:- On a first probe it reads the zeroed struct from
qcom_spi_probe(), so steps, bytes andbbm_sizeare 0. The count then returns 0 rather than an error, so the probe continues withmtd->oobavailset to 0.- On a probe retry it reads the
ecc_cfgthe previous attempt freed.A retry is easy to hit. On IPQ5018 with the qcom,smem-part parser the partition parse returns -EPROBE_DEFER until SMEM has probed, so the first spi-nand probe defers. It defers inside
mtd_device_parse_register(), aftermtd_otp_nvmem_add()has already read the factory OTP - that read goes throughprepare_io_reqand leavessnandc->qspi->eccpointing at the context thatspinand_cleanup()then frees. The second probe allocates a new context, never publishes it, and computes the OOB layout from the freed one. Once the slab has been reused,qecc->stepsholds garbage andoobregion->length = qecc->steps * 4;goes negative.
qcom_spi_ooblayout_free()only reports-ERANGEfor section 1 and later, somtd_ooblayout_count_bytes()sums the regions and returns that negative length as the byte count. The -512 below is steps * 4 with steps == -128. It is a byte count that happens to collide with-ERESTARTSYS, not an error the driver returned.spinand_init()takes it as an error, and because it is not -EPROBE_DEFER the driver core never retries and the NAND never appears:spi-nand spi0.0: ESMT SPI NAND was found.
spi-nand spi0.0: probe with driver spi-nand failed with error -512 UBI error: cannot open mtd rootfs, error -2
Waiting for root device/dev/ubiblock0_1...On a Mercusys MR80X (IPQ5018, ESMT F50D1G41LB) about half of the boots failed to mount the rootfs, the outcome depending on whether the freed memory had been overwritten yet.
Publish the context when it is created and clear the pointer when it is destroyed. Clearing leaves
snandc->qspi->eccNULL after cleanup, which is safe: the mtd is unregistered beforecleanup_ctxruns, so no ooblayout callback can follow.
Quoted 6 lines
Fixes 7304d1909080 ("spi: spi-qpic: add driver for QCOM SPI NAND flash Interface")Signed-off-by Johan Alvarado <[email protected]>---
Tested on a Mercusys MR80X (IPQ5018, ESMT F50D1G41LB) running 6.18.44 with the equivalent change; mainline build-tested with W=1, no warnings.
Tested on top of v7.3-rc2, running on the Tp-Link Archer AX55 v1. It works as expected, yet I have some comments, see below.
drivers/spi/spi-qpic-snand.c static int qcom_spi_ecc_init_ctx_pipelined(struct nand_device *nand) · line 414
Quoted 13 lines
drivers/spi/spi-qpic-snand.c | 3 +++ 1 file changed, 3 insertions(+)drivers/spi/spi-qpic-snand.c +1
-0@@ -411,6 +411,8 @@ static int qcom_spi_ecc_init_ctx_pipelined(struct nand_device *nand)dev_dbg (snandc->dev,"ECC strength: %u bits per %u bytes\n" , ecc_cfg->strength, ecc_cfg->step_size); + snandc->qspi->ecc = ecc_cfg;
For the sake of completeness we should remove the identical assignment from the qcom_spi_ecc_prepare_io_req_pipelined() function as it gets redundant after the change.
Additionally, the zeroed ecc_cfg instance allocated in qcom_spi_probe() become unused so the allocation can be dropped. However, since this is not strictly required for fixing the use-after-free issue, it could be done in a separate patch.
Regards,
Gabor