Skip to contentSkip to conversation

arm64: dts: imx8mn-bsh-smm-s2/pro: add boot phase properties

PATCH New Dario Binacchi 1 participant 1 message Nov 20

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm64: dts: imx8mn-bsh-smm-s2/pro: add boot phase properties

Add boot phase properties to the resources needed during the boot process.

The BSH SMM S2 and S2PRO need UART, watchdog, PMIC, GPIO and boot device access.

Tested on BSH SMM S2PRO with U-Boot v2027.01-rc1.

---

 .../freescale/imx8mn-bsh-smm-s2-common.dtsi   | 22 +++++++++++++++++++
 .../boot/dts/freescale/imx8mn-bsh-smm-s2.dts  |  2 ++
 .../dts/freescale/imx8mn-bsh-smm-s2pro.dts    |  2 ++
 3 files changed, 26 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi +22 -0
index d20393c2d901..5515236d3c09 100644
@@ -77,10 +77,23 @@ ethphy0: ethernet-phy@0 {
 	};
 };
 
+&gpio1 {
+	bootph-pre-ram;
+};
+
+&gpio2 {
+	bootph-pre-ram;
+};
+
+&gpio4 {
+	bootph-pre-ram;
+};
+
 &i2c1 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
+	bootph-pre-ram;
 	status = "okay";
 
 	bd71847: pmic@4b {
@@ -95,8 +108,11 @@ bd71847: pmic@4b {
 		#clock-cells = <0>;
 		clocks = <&osc_32k>;
 		clock-output-names = "clk-32k-out";
+		bootph-pre-ram;
 
 		regulators {
+			bootph-pre-ram;
+
 			buck1_reg: BUCK1 {
 				/* PMIC_BUCK1 - VDD_SOC */
 				regulator-name = "buck1";
@@ -244,6 +260,7 @@ bluetooth {
 &uart4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart4>;
+	bootph-pre-ram;
 	status = "okay";
 };
 
@@ -280,6 +297,7 @@ &wdog1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wdog>;
 	fsl,ext-reset-output;
+	bootph-pre-ram;
 	status = "okay";
 };
 
@@ -326,6 +344,7 @@ pinctrl_i2c1: i2c1grp {
 			MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL			0x400000c2
 			MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA			0x400000c2
 		>;
+		bootph-pre-ram;
 	};
 
 	pinctrl_i2c3: i2c3grp {
@@ -346,6 +365,7 @@ pinctrl_pmic: pmicirqgrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x040
 		>;
+		bootph-pre-ram;
 	};
 
 	pinctrl_uart2: uart2grp {
@@ -369,6 +389,7 @@ pinctrl_uart4: uart4grp {
 			MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX		0x040
 			MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX		0x040
 		>;
+		bootph-pre-ram;
 	};
 
 	pinctrl_usdhc2: usdhc2grp {
@@ -414,6 +435,7 @@ pinctrl_wdog: wdoggrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0x046
 		>;
+		bootph-pre-ram;
 	};
 
 	pinctrl_wlan: wlangrp {
arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2.dts +2 -0
index 11a1ba5bfdb7..5add6a8e1c59 100644
@@ -21,6 +21,7 @@ memory@40000000 {
 &gpmi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	bootph-pre-ram;
 	status = "okay";
 };
 
@@ -43,5 +44,6 @@ MX8MN_IOMUXC_NAND_READY_B_RAWNAND_READY_B	0x00000056
 			MX8MN_IOMUXC_NAND_WE_B_RAWNAND_WE_B		0x00000096
 			MX8MN_IOMUXC_NAND_WP_B_RAWNAND_WP_B		0x00000096
 		>;
+		bootph-pre-ram;
 	};
 };
arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2pro.dts +2 -0
index 475cbf9e0d1e..b48905a9b4dd 100644
@@ -85,6 +85,7 @@ &usdhc1 {
 	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
 	bus-width = <8>;
 	non-removable;
+	bootph-pre-ram;
 	status = "okay";
 };
 
@@ -133,6 +134,7 @@ MX8MN_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x0d0
 			MX8MN_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x0d0
 			MX8MN_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x090
 		>;
+		bootph-pre-ram;
 	};
 
 	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {

---
base-commit: 65e4fd942f72a9dba0e4e257290c4fa1aa756854
branch: imx8mn-bsh-smm-s2-bootph

Signature · 1 line
2.43.0