LXT972 issue on MPC8247: tx error
my code run on the board reveal the info as following:
Board: Motorola MPC8272ADS DRAM: 32 MB FLASH: 512 kB In: serial Out: serial Err: serial Net: FCC1 ETHERNET
bb_miiphy_write()
Hit any key to stop autoboot: 0
=>
after i enter words like "ping 192.168.0.100",show something like this PS. the line start as "chengmo" are debug infos
chengmo : fec_init
chengmo 0 : rtx.txbd[0].cbd_sc : 00004c00
chengmo 1 : rtx.txbd[1].cbd_sc : 00004c00
Using FCC1 ETHERNET device
chengmo : fec_sendchengmo_b : rtx.txbd[0].cbd_sc : 00004c00chengmo_a : rtx.txbd[0].cbd_sc : 0000ec00
fec: tx error
chengmo : fec_send
fec: tx buffer not ready
ping failed; host 192.168.0.100 is not alive
eventually, show me that "fec: tx buffer not ready." this prompt is in fec_send() in ether_fcc.c
i am not sure that at which the mistake happened, because the flow of initializing is:
eth_initialize() => phy_reset()
in eth_initialize(), insert the struct into the list of devices.
phy_reset(), emulates MII transmit something to PHY, is it right? here i am not sure about it.
after i input PING command, it will run by sequence fec_init(), fec_send()
in fec_init(), configure some register about FCC, and setup ethernet buffer discriptors and allocate space for buffer used by Tx and Rx, then initialize Parameter RAM. that' all, something wrong ?
where the mistakes could happen ? i really cant find it.
Signature · 2 lines
View this message in context: http://www.nabble.com/LXT972-issue-on-MPC8247%3A-tx-error-tp22533735p22533735.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Hi Sauce.Cheng,
Quoted 30 lines · Sauce.Cheng
my code run on the board reveal the info as following:
Board: Motorola MPC8272ADS DRAM: 32 MB FLASH: 512 kB In: serial Out: serial Err: serial Net: FCC1 ETHERNET
bb_miiphy_write()
Hit any key to stop autoboot: 0
=>after i enter words like "ping 192.168.0.100",show something like this PS. the line start as "chengmo" are debug infos
chengmo :
fec_init
chengmo 0 : rtx.txbd[0].cbd_sc :00004c00
chengmo 1 : rtx.txbd[1].cbd_sc :00004c00
Using FCC1 ETHERNET device
chengmo :fec_sendchengmo_b: rtx.txbd[0].cbd_sc :00004c00chengmo_a: rtx.txbd[0].cbd_sc :0000ec00
fec: tx error
chengmo :fec_send
fec: tx buffer not ready
ping failed; host 192.168.0.100 is not aliveeventually, show me that "fec: tx buffer not ready." this prompt is in
fec_send()inether_fcc.c
[snip]
Quoted 1 line
where the mistakes could happen ? i really cant find it.
Your FEC (Tx) most likely is not being clocked. Check your QE clock configurations, verify that your PHY/MAC/??? is generating the correct clocks, etc.
FWIIW, I had this happen on my board because the H/W designer strapped the PHY to power up with the clocks disabled (lowers power). I have to flip a bit in a PHY register to enable clocks. (I'm using a different processor and different PHY, YMMV.)
HTH,
gvb
thanks Jerry Van Baren-7
sorry about my postpone replying
the problem have solved some days ago, thanks for your suggestion about clocks configurate, though it's
not clocks' bussiness.
the register cmx_uar is mistake, i have fixed it up by manual. everything is done
later i will take the details of this problem:s
best regards
thanks!
Sauce
Signature · 2 lines
View this message in context: http://www.nabble.com/LXT972-issue-on-MPC8247%3A-tx-error-tp22533735p22861063.html Sent from the Uboot - Users mailing list archive at Nabble.com.