Skip to contentSkip to conversation

U-Boot 2009.03 booting problem

U-Boot rudresh 2 participants 2 messages Apr 9, 2009

lore
Share & tools
lore

rudresh

author
#0 lore raw

Hi All,

I am try to use the u-boot version 2009 for MPC8313ERB broad, when i load the u-boot.bin to board using JTAG and restart the board at that time its not booting properly . its generated following error what may be the problem.

U-Boot 2009.03 (Apr 22 2009 - 04:59:44) MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c3, MPC8313E, Rev: 1.0 at 333.333 MHz, CSB: 166.667 MHz
Board: Freescale MPC8313ERDB
I2C:   ready
DRAM:  128 MB
FLASH: 16 MB
NAND:  256 MiB

*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial

Machine check in kernel mode.
Caused by (from msr): regs 07f36df0 Unknown values in msr
NIP: 07FE9474 XER: 00000000 LR: 07FE946C REGS: 07f36df0 TRAP: 0200 DAR:
00000000
MSR: 00003030 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 11

GPR00: 0000007C 07F36EE0 07F36F4C FFFFFFFF FFFFFFFF 00000000 00000000 04AA7D46
GPR08: 07FBDE54 F001C048 00000090 07FEA3D0 07F36F4C 000080A0 07FFC000 09FB9000
GPR16: 00000080 00006101 20044000 00020052 FFFFFFFF FFFFFFFF 00000000 07FBC098
GPR24: 07FBCAD8 FFFF80A0 00000001 FE7FE000 00002000 00000000 07FFD5A4 07F36FBC
Call backtrace:
07FE946C 07FE1784 07FBD968 07FBC5E8
machine check
Resetting the board.

Regards
Rudresh

Signature · 2 lines
View this message in context: http://www.nabble.com/-U-boot--U-Boot-2009.03-booting-problem-tp22969997p22969997.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#1 lore raw
Quoted 20 lines · On Thu, 9 Apr 2009 05:32:29 -0700 (PDT) rudresh <[email protected]> wrote:

Hi All,

I am try to use the u-boot version 2009 for MPC8313ERB broad, when i load the u-boot.bin to board using JTAG and restart the board at that time its not booting properly . its generated following error what may be the problem.

U-Boot 2009.03 (Apr 22 2009 - 04:59:44) MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c3, MPC8313E, Rev: 1.0 at 333.333 MHz, CSB: 166.667 MHz
Board: Freescale MPC8313ERDB
I2C:   ready
DRAM:  128 MB
FLASH: 16 MB
NAND:  256 MiB

*** Warning - bad CRC, using default environment

Quoted 7 lines
In:    serial
Out:   serial
Err:   serial

Machine check in kernel mode.
Caused by (from msr): regs 07f36df0 Unknown values in msr
NIP: 07FE9474 XER: 00000000 LR: 07FE946C REGS: 07f36df0 TRAP: 0200 DAR:
00000000

can you turn on debugging and/or somehow find out what code is at or around the NIP address above?

Also, how, if any, is this board different from Freescale's MPC8313ERDB? earlier you state it is a custom board...

Kim