Skip to contentSkip to conversation

Mismatch between hdaprm and sdparm output

DISCUSSION Keith Owens 2 participants 2 messages Aug 7, 2006

lore
Share & tools
lore
#0 lore raw

NEC Versa S5200 laptop with FUJITSU MHV2080B SATA disk. Kernel 2.6.16.21-0.13-smp (suselinux 10.1) using ata_piix. hdparm and sdparm give inconsistent results, which one should I believe? My main concern is write caching (XFS filesystem).

hdparm -I

/dev/sda:

ATA device, with non-removable media

	Model Number:       FUJITSU MHV2080BH
	Serial Number:      NW28T62255WF
	Firmware Revision:  00000028
Standards:
	Supported: 7 6 5 4
	Likely used: 7
Configuration:
	Logical		max	current
	cylinders	16383	16383
	heads		16	16
	sectors/track	63	63
	--
	CHS current addressable sectors:   16514064
	LBA    user addressable sectors:  156301488
	LBA48  user addressable sectors:  156301488
	device size with M = 1024*1024:       76319 MBytes
	device size with M = 1000*1000:       80026 MBytes (80 GB)

Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: 128 (0x80)
Recommended acoustic management value: 254, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
* Automatic Acoustic Management feature set
* SET MAX security extension
* Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
* General Purpose Logging feature set
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
80min for SECURITY ERASE UNIT.
Checksum: correct

sdparm --get=WCE

    /dev/sda: ATA       FUJITSU MHV2080B  0000

WCE 1

hdparm -A 1/0 can set/clear write cache, sdparm --set=WCE=0/1 always gets an error:

sdparm --set=WCE=0 /dev/sda
/dev/sda: ATA FUJITSU MHV2080B 0000
change_mode_page: failed setting page: Caching (SBC)

#1 lore raw
Quoted 4 lines · Keith Owens

NEC Versa S5200 laptop with FUJITSU MHV2080B SATA disk. Kernel 2.6.16.21-0.13-smp (suselinux 10.1) using ata_piix. hdparm and sdparm give inconsistent results, which one should I believe? My main concern is write caching (XFS filesystem).

well write caching you should be able to benchmark easily.. does, say, dbench or tiobench show any difference ?