potential Uboot Ping problem
Hi,
It appears the ping in UBOOT is broken. The ping works fine if you have a network connection. But if the network connection is disconnected the ping hangs the system. There is no response to Control-C either. I have to power cycle the proto to get back to a UBOOT prompt. Is this a known issue or did I possibly break something?
I have a board based on the Atmel AT91SAM9RL-EK. My theory is that it "may" be a generic problem with the uboot ping. I can't confirm that since the only hardware I have is our protos.
Does anyone else have a board with another MAC/PHY that you can try this on?
As for UBOOT code, our environment is based on 2008.10 code. Our MAC/PHY is the Microchip ENC28J60.
Thanks,
Steve
Signature · 2 lines
View this message in context: http://www.nabble.com/potential-Uboot-Ping-problem-tp23815872p23815872.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Premi
Quoted 19 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Steven Zedeck
Sent: Monday, June 01, 2009 8:05 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] potential Uboot Ping problemHi,
It appears the ping in UBOOT is broken. The ping works fine if you have a
network connection. But if the network connection is disconnected the ping
hangs the system. There is no response to Control-C either. I have to power
cycle the proto to get back to a UBOOT prompt. Is this a known issue or did
I possibly break something?
Quoted 5 lines
I have a board based on the Atmel AT91SAM9RL-EK. My theory is that it "may"
be a generic problem with the uboot ping. I can't confirm that since the
only hardware I have is our protos.
It was noticed on the OMAP3EVM last FRI and we were suspecting it to be problem with the omap3 board configuration itself. (Though did not spend much time in debug).
Now, I too get a feeling that it could be a generic problem.
Best regards,
Sanjeev
Quoted 23 lines
Does anyone else have a board with another MAC/PHY that you can try this on?
As for UBOOT code, our environment is based on 2008.10 code. Our MAC/PHY is
the Microchip ENC28J60.Thanks,
SteveSignature · 9 lines
View this message in context: http://www.nabble.com/potential-Uboot-Ping-problem-tp23815872p 23815872.html Sent from the Uboot - Users mailing list archive at Nabble.com. _______________________________________________ U-Boot mailing list U-Boot at lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
I guess thats good news. I looked inside the cmd_ping code a bit. I bet there's a "while" loop somewhere that is waiting for something and may not have a timeout loop. Any ideas?
Thanks,
Steve
Quoted 63 lines · Sanjeev
Quoted 20 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Steven Zedeck
Sent: Monday, June 01, 2009 8:05 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] potential Uboot Ping problemHi,
It appears the ping in UBOOT is broken. The ping works fine if you have a
network connection. But if the network connection is disconnected the ping
hangs the system. There is no response to Control-C either. I have to power
cycle the proto to get back to a UBOOT prompt. Is this a known issue or did
I possibly break something?Quoted 5 lines
I have a board based on the Atmel AT91SAM9RL-EK. My theory is that it "may"
be a generic problem with the uboot ping. I can't confirm that since the
only hardware I have is our protos.It was noticed on the OMAP3EVM last FRI and we were suspecting it to be problem with the omap3 board configuration itself. (Though did not spend much time in debug).
Now, I too get a feeling that it could be a generic problem.
Best regards,
SanjeevQuoted 4 lines
Does anyone else have a board with another MAC/PHY that you can try this on?
Quoted 19 lines
As for UBOOT code, our environment is based on 2008.10 code. Our MAC/PHY is
the Microchip ENC28J60.Thanks,
SteveSignature · 9 lines
View this message in context: http://www.nabble.com/potential-Uboot-Ping-problem-tp23815872p 23815872.html Sent from the Uboot - Users mailing list archive at Nabble.com. _______________________________________________ U-Boot mailing list U-Boot at lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Signature · 2 lines
View this message in context: http://www.nabble.com/potential-Uboot-Ping-problem-tp23815872p23816429.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Hi Steven,
Quoted 6 lines · Steven Zedeck
I guess thats good news. I looked inside the
cmd_pingcode a bit. I bet there's a "while" loop somewhere that is waiting for something and may not have a timeout loop. Any ideas?Thanks,
Steve
Please don't top post, it makes the conversation hard to follow.
http://www.caliburn.nl/topposting.html
Quoted 31 lines
Quoted 30 lines · Sanjeev
Quoted 20 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Steven Zedeck
Sent: Monday, June 01, 2009 8:05 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] potential Uboot Ping problemHi,
It appears the ping in UBOOT is broken. The ping works fine if you have a
network connection. But if the network connection is disconnected the ping
hangs the system. There is no response to Control-C either. I have to power
cycle the proto to get back to a UBOOT prompt. Is this a known issue or did
I possibly break something?Quoted 5 lines
I have a board based on the Atmel AT91SAM9RL-EK. My theory is that it "may"
be a generic problem with the uboot ping. I can't confirm that since the
only hardware I have is our protos.It was noticed on the OMAP3EVM last FRI and we were suspecting it to be problem with the omap3 board configuration itself. (Though did not spend much time in debug).
Quoted 7 lines
Quoted 7 lines
Now, I too get a feeling that it could be a generic problem.
Best regards,
SanjeevQuoted 3 lines
Does anyone else have a board with another MAC/PHY that you can try this on?
Ideally, if there is no link, the ping command should just exit gracefully without attempting network operations. Eg on my 8561-based board with no cables plugged in:
=> ping 192.168.1.1
Auto-neg error, defaulting to 10BT/HD
eTSEC1: No link.
Auto-neg error, defaulting to 10BT/HD
eTSEC2: No link.
ping failed; host 192.168.1.1 is not alive
<there is no delay in the printing of the above info>.
The tsec driver's init function returns -1 when link isn't detected. Perhaps your ethernet driver should do the same?
What happens if you ping a non-existent IP address? Does that also hang the board? Do other network operations hang the board if no ethernet cable is plugged in?
Best,
Peter
Quoted 73 lines · Peter Tyser
Hi Steven,
Quoted 7 lines · Steven Zedeck
I guess thats good news. I looked inside the
cmd_pingcode a bit. I bet there's a "while" loop somewhere that is waiting for something and may not
have a timeout loop. Any ideas?Thanks,
StevePlease don't top post, it makes the conversation hard to follow.
http://www.caliburn.nl/topposting.htmlQuoted 31 lines
Quoted 30 lines · Sanjeev
Quoted 20 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Steven Zedeck
Sent: Monday, June 01, 2009 8:05 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] potential Uboot Ping problemHi,
It appears the ping in UBOOT is broken. The ping works fine if you have a
network connection. But if the network connection is disconnected the ping
hangs the system. There is no response to Control-C either. I have to power
cycle the proto to get back to a UBOOT prompt. Is this a known issue or did
I possibly break something?Quoted 5 lines
I have a board based on the Atmel AT91SAM9RL-EK. My theory is that it "may"
be a generic problem with the uboot ping. I can't confirm that since the
only hardware I have is our protos.It was noticed on the OMAP3EVM last FRI and we were suspecting it to be problem with the omap3 board configuration itself. (Though did not spend much time in debug).
Quoted 7 lines
Quoted 7 lines
Now, I too get a feeling that it could be a generic problem.
Best regards,
SanjeevQuoted 3 lines
Does anyone else have a board with another MAC/PHY that you can try this on?
Ideally, if there is no link, the ping command should just exit gracefully without attempting network operations. Eg on my 8561-based board with no cables plugged in:
=> ping 192.168.1.1
Auto-neg error, defaulting to 10BT/HD
eTSEC1: No link.
Auto-neg error, defaulting to 10BT/HD
eTSEC2: No link.
ping failed; host 192.168.1.1 is not alive<there is no delay in the printing of the above info>.
The tsec driver's init function returns -1 when link isn't detected. Perhaps your ethernet driver should do the same?
What happens if you ping a non-existent IP address? Does that also hang the board? Do other network operations hang the board if no ethernet cable is plugged in?
Quoted 9 lines
Best,
Peter_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
The ethernet driver is also from the uboot distribution. Its enc28j60.c. I'll need to go through it to see where its hanging assuming its in that driver or the ping code that calls it.
thanks,
Steve
Signature · 2 lines
View this message in context: http://www.nabble.com/potential-Uboot-Ping-problem-tp23815872p23824737.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Premi
Quoted 74 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Peter Tyser
Sent: Tuesday, June 02, 2009 3:53 AM
To: Steven Zedeck
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] potential Uboot Ping problemHi Steven,
Quoted 1 line · Steven Zedeck
I guess thats good news. I looked inside the
cmd_pingcodea bit. I bet
Quoted 1 line
there's a "while" loop somewhere that is waiting for
something and may not
Quoted 4 lines
have a timeout loop. Any ideas?
Thanks,
StevePlease don't top post, it makes the conversation hard to follow.
http://www.caliburn.nl/topposting.htmlQuoted 31 lines
Quoted 30 lines · Sanjeev
Quoted 20 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Steven Zedeck
Sent: Monday, June 01, 2009 8:05 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] potential Uboot Ping problemHi,
It appears the ping in UBOOT is broken. The ping works fine if you have a
network connection. But if the network connection is disconnected the ping
hangs the system. There is no response to Control-C either. I have to power
cycle the proto to get back to a UBOOT prompt. Is this a known issue or did
I possibly break something?Quoted 5 lines
I have a board based on the Atmel AT91SAM9RL-EK. My theory is that it "may"
be a generic problem with the uboot ping. I can't confirm that since the
only hardware I have is our protos.It was noticed on the OMAP3EVM last FRI and we were suspecting it to be problem with the omap3 board configuration itself. (Though did not spend much time in debug).
Quoted 7 lines
Quoted 7 lines
Now, I too get a feeling that it could be a generic problem.
Best regards,
SanjeevQuoted 3 lines
Does anyone else have a board with another MAC/PHY that you can try this on?
Ideally, if there is no link, the ping command should just exit gracefully without attempting network operations. Eg on my 8561-based board with no cables plugged in:
=> ping 192.168.1.1
Auto-neg error, defaulting to 10BT/HD
eTSEC1: No link.
Auto-neg error, defaulting to 10BT/HD
eTSEC2: No link.
ping failed; host 192.168.1.1 is not alive<there is no delay in the printing of the above info>.
Quoted 7 lines
The tsec driver's init function returns -1 when link isn't detected. Perhaps your ethernet driver should do the same?
What happens if you ping a non-existent IP address? Does that also hang
the board? Do other network operations hang the board if no ethernet cable is plugged in?
Here is a session from OMAP3EVM:
OMAP3_EVM # setenv autoload noOMAP3_EVM # dhcp
smc911x: initializing
smc911x: detected LAN9115 controller
smc911x: phy initialized
smc911x: MAC 00:50:c2:7e:88:72
BOOTP broadcast 1
BOOTP broadcast 2
DHCP client bound to address 192.168.1.10OMAP3_EVM # ping 192.168.1.1
smc911x: initializing
smc911x: detected LAN9115 controller
smc911x: phy initialized
smc911x: MAC 00:50:c2:7e:88:72
ping failed; host 192.168.1.1 is not aliveOMAP3_EVM #
Quoted 9 lines
Best,
Peter_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot