Skip to contentSkip to conversation

Problem with uboot booting image

U-Boot Rahanesh 1 participant 1 message Jun 23, 2009

lore
Share & tools
lore

Rahanesh

author
#0 lore raw

Hi All,

I am trying to boot Linux from uboot. I have cross compiled Linux and ramdisk for my board. After cross compilation i did a tftp to download the image(Linux + Filesystem) to RAM(0x80800000) . From there i copied it to flash(0xad040000).

Now on a reset u boot comes up and then when trying to bring LINUX it throws an error saying

Verifying Checksum.......Bad data CRC.

Then uboot prompt appears.

This is what happened.....

U-Boot 1.1.2 (Jun 10 2008 - 18:55:13)

Board: MIPS CPU Speed 200 MHz
DRAM:  16 MB

sflash.c:266:DF_F_DataflashProbe: Entered sflash.c:269:DF_F_DataflashProbe: flash type is 0x1 sflash.c:270:DF_F_DataflashProbe: num pages 32768 DataFlash:Nb pages: 32768
Page Size: 256
Size= 8388608 bytes

Logical address: 0xAD000000
Nb Erase Blocks:    128
Erase Block Size:  65536

Area 0: AD000000 to AD003FFF
Area 1: AD004000 to AD03FFFF
Area 2: AD040000 to AD30BFFF
Area 3: AD30C000 to AD7FFFFF
crc matched

In:    serial
Out:   serial
Err:   serial
Net:    Eth.

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot: 0
### JFFS2 loading '/boot/uImage' to 0x80800000 Scanning JFFS2 FS: .................... done.
### JFFS2 load complete: 3249008 bytes loaded to 0x80800000 ## Booting image at 80800000 ...

   Image Name:   Linux Kernel Image with ramdisk.
   Created:      2009-06-22   4:37:12 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    3248944 Bytes =  3.1 MB

Load Address: 80100000
Entry Point: 80578000
Verifying Checksum ... Bad Data CRC
UBOOT>

UBOOT # printenv
bootargs=console=ttyS0,38400 nofpu mem=14M root=/dev/ram0 rw bootcmd=fsload 0x80800000 /boot/uImage; bootm 0x80800000 bootdelay=5
baudrate=38400
ethaddr=00:06:0D:00:00:00
preboot=echo;echo Type "run flash_nfs" to mount root filesystem over NFS;echo
nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) btargs=setenv bootargs console=ttyS0,$(baudrate) nofpu mem=30M root=/dev/ram0 rw
addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmas k):$(hostname):$(netdev):off
addmisc=setenv bootargs $(bootargs) console=ttyS0,$(baudrate) ethaddr=$(ethaddr)
panic=1
flash_nfs=run nfsargs addip addmisc;bootm $(kernel_addr) flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr) net_nfs=tftp 80500000 $(bootfile);run nfsargs addip addmisc;bootm netbootfile=uImage
jffsfile=jffs.1.1
progjffs=tftp 0x80800000 $(jffsfile); erase 0xad040000 0xad3bffff; cp.b 0x808000
00 0xad040000 $(filesize)
imget=tftp 0x80800000 refmta.bin;erase 0xad000000 0xad3e0000;cp.b 0x80800000 0xa
d000000 $(filesize)
localbootfile=/boot/uImage
bootnet=tftp 0x80800000 $(netbootfile); bootm 0x80800000 kernel_addr=AD040000
u-bootfile=u-boot.ctlm.bin
load-ub=tftp 80504000 $(u-bootfile)
update-ub=protect off 1:0-4;cp.b AD000000 80500000 4000;cp.b AD03F000 8053F000 1
000;erase 0xAD000000 0xAD03ffff;cp.b 80500000 AD000000 0x40000 btlinux=fsload 0x80800000 $(localbootfile); bootm 0x80800000 ethact=Eth.
netmask=255.255.0.0
serverip=10.47.3.54
ipaddr=10.47.252.254
stdin=serial
stdout=serial
stderr=serial
filesize=319370

Environment size: 1554/4092 bytes

Please throw some light on this.

Thanks
Rahanesh

Signature · 2 lines
View this message in context: http://www.nabble.com/Problem-with-uboot-booting-image-tp24160664p24160664.html
Sent from the Uboot - Users mailing list archive at Nabble.com.