phy: rockchip-usb: add handler for usb-uart functionality
Subsystems (3)
Heiko Stübner
maintainerPATCH v4 1/1 phy: rockchip-usb: add handler for usb-uart functionality
Most newer Rockchip SoCs provide the possibility to use a usb-phy as passthrough for the debug uart (uart2), making it possible to for example get console output without needing to open the device.
This patch adds an early_initcall to enable this functionality conditionally via the commandline and also disables the corresponding usb controller in the devicetree.
Currently only data for the rk3288 is provided, but at least the rk3188 and arm64 rk3368 also provide this functionality and will be enabled later.
On a spliced usb cable the signals are tx on white wire(D+) and rx on green wire(D-).
The one caveat is that currently the reconfiguration of the phy happens as early_initcall, as the code depends on the unflattened devicetree being available. Everything is fine if only a regular console is active as the console-replay will happen after the reconfiguation. But with earlycon active output up to smp-init currently will get lost.
The phy is an optional property for the connected dwc2 controller, so we still provide the phy device but fail all phy-ops with -EBUSY to make sure the dwc2 does not try to transmit anything on the repurposed phy.
---
changes in v4:
- drop the rest of the phy-series, as the patches have gotten applied
So far, this hasn't gotten eyeballs yet, so citing discussion-parts from the v3 coverletter:
The patch, while not associated with the new pll handling, also builds on the groundwork introduced there and adds support for the function repurposing one of the phys as passthrough for uart-data. This enables attaching a ttl converter to the D+ and D- pins of an usb cable to receive uart data this way, when it is not really possible to attach a regular serial console to a board.
One point of critique in my first iteration [0] of this was, that due to when the reconfiguration happens we may miss parts of the logs when earlycon is enabled. So far early_initcall gets used as the unflattened devicetree is necessary to set this up. Doing this for example in the early_param directly would require parsing the flattened devicetree to get needed nodes and properties.
I still maintain that if you're working on anything before smp-bringup you should use a real dev-board instead or try to solder uart cables on hopefully available test-points .
Documentation/kernel-parameters.txt | 6 + drivers/phy/phy-rockchip-usb.c | 231 ++++++++++++++++++++++++++++++------ 2 files changed, 201 insertions(+), 36 deletions(-)
Documentation/kernel-parameters.txt +6 -0
@@ -3486,6 +3486,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted. ro [KNL] Mount root device read-only on boot + rockchip.usb_uart + Enable the uart passthrough on the designated usb port + on Rockchip SoCs. When active, the signals of the + debug-uart get routed to the D+ and D- pins of the usb + port and the regular usb controller gets disabled. + root= [KNL] Root filesystem See name_to_dev_t comment in init/do_mounts.c.
drivers/phy/phy-rockchip-usb.c +195 -36
317 lines not on this page · raw message
Signature · 1 line
2.6.4
kbuild test robot
build botreproduce: wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # save the attached .config to linux build tree…
Hi Heiko,
[auto build test ERROR on rockchip/for-next]
[also build test ERROR on v4.5-rc1 next-20160125]
[if your patch is applied to the wrong git tree, please drop us a note to help improving the system]
url: https://github.com/0day-ci/linux/commits/Heiko-St-bner/phy-rockchip-usb-add-handler-for-usb-uart-functionality/20160126-082429 base: https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git for-next config: arm-defconfig (attached as .config)
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=arm
All error/warnings (new ones prefixed by >>):
In file included from drivers/phy/phy-rockchip-usb.c:21:0:
include/linux/module.h:128:27: error: redefinition of '__inittest'
static inline initcall_t __inittest(void) \
^
include/linux/module.h:107:29: note: in expansion of macro 'module_init'
#define early_initcall(fn) module_init(fn)
^
>> drivers/phy/phy-rockchip-usb.c:481:1: note: in expansion of macro 'early_initcall'
early_initcall(rockchip_init_usb_uart);
^
include/linux/module.h:128:27: note: previous definition of '__inittest' was here
static inline initcall_t __inittest(void) \
^
>> include/linux/device.h:1332:1: note: in expansion of macro 'module_init'
module_init(__driver##_init); \
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^
>> drivers/phy/phy-rockchip-usb.c:436:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(rockchip_usb_driver);
^
include/linux/module.h:130:6: error: redefinition of 'init_module'
int init_module(void) __attribute__((alias(#initfn)));
^
include/linux/module.h:107:29: note: in expansion of macro 'module_init'
#define early_initcall(fn) module_init(fn)
^
>> drivers/phy/phy-rockchip-usb.c:481:1: note: in expansion of macro 'early_initcall'
early_initcall(rockchip_init_usb_uart);
^
include/linux/module.h:130:6: note: previous definition of 'init_module' was here
int init_module(void) __attribute__((alias(#initfn)));
^
>> include/linux/device.h:1332:1: note: in expansion of macro 'module_init'
module_init(__driver##_init); \
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^
>> drivers/phy/phy-rockchip-usb.c:436:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(rockchip_usb_driver);
^
>> drivers/phy/phy-rockchip-usb.c:488:13: error: expected declaration specifiers or '...' before string constant
early_param("rockchip.usb_uart", rockchip_usb_uart);
^
>> drivers/phy/phy-rockchip-usb.c:488:34: error: expected declaration specifiers or '...' before 'rockchip_usb_uart'
early_param("rockchip.usb_uart", rockchip_usb_uart);
^ drivers/phy/phy-rockchip-usb.c:483:19: warning: 'rockchip_usb_uart' defined but not used [-Wunused-function]
static int __init rockchip_usb_uart(char *buf)
^
vim +488 drivers/phy/phy-rockchip-usb.c
430 .driver = {
431 .name = "rockchip-usb-phy",
432 .of_match_table = rockchip_usb_phy_dt_ids,
433 },
434 };
435
> 436 module_platform_driver(rockchip_usb_driver);
437
438 static int __init rockchip_init_usb_uart(void)
439 {
440 const struct of_device_id *match;
441 const struct rockchip_usb_phy_pdata *data;
442 struct device_node *np;
443 struct regmap *grf;
444 int ret;
445
446 if (!enable_usb_uart)
447 return 0;
448
449 np = of_find_matching_node_and_match(NULL, rockchip_usb_phy_dt_ids,
450 &match);
451 if (!np) {
452 pr_err("%s: failed to find usbphy node\n", __func__);
453 return -ENOTSUPP;
454 }
455
456 pr_debug("%s: using settings for %s\n", __func__, match->compatible);
457 data = match->data;
458
459 if (!data->init_usb_uart) {
460 pr_err("%s: usb-uart not available on %s\n",
461 __func__, match->compatible);
462 return -ENOTSUPP;
463 }
464
465 grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf");
466 if (IS_ERR(grf)) {
467 pr_err("%s: Missing rockchip,grf property, %lu\n",
468 __func__, PTR_ERR(grf));
469 return PTR_ERR(grf);
470 }
471
472 ret = data->init_usb_uart(grf);
473 if (ret) {
474 pr_err("%s: could not init usb_uart, %d\n", __func__, ret);
475 enable_usb_uart = 0;
476 return ret;
477 }
478
479 return 0;
480 }
> 481 early_initcall(rockchip_init_usb_uart);
482
483 static int __init rockchip_usb_uart(char *buf)
484 {
485 enable_usb_uart = true;
486 return 0;
487 }
> 488 early_param("rockchip.usb_uart", rockchip_usb_uart); 489
490 MODULE_AUTHOR("Yunzhi Li <[email protected]>");
491 MODULE_DESCRIPTION("Rockchip USB 2.0 PHY driver");
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
-------------- next part --------------
A non-text attachment was scrubbed...
Name: .config.gz
Type: application/octet-stream
Size: 36561 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160126/e4aba1f0/attachment-0001.obj>