board doesnt boot when migrating from u-boot1.3.4 to u-boot2009.11.1
Dear all,
I was using u-boot-1.3.4 all these days . i decide to shift to new u-boot so that i can use some new features . i compiled the latest u-boot-2009.11.1 .but my board doesnt boot at all . My board is based on AT91SAM9261EK. i did a couple of changes to u-boot which i'm listing below
1) In the config file /include/configs/at91sam9261ek.h i changed the line
#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */
to
#define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */ since i have 128MB
SDRAM on my board.
and
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load
address */
to
#define CONFIG_SYS_LOAD_ADDR 0x27D00000 /* load address */
this is to reflect the change in bootstrap code to copy u-boot to higher address in SDRAM so tat RFS of size > 64MB can be copied .
3) and finally in the file/home/ravikulkarni/denx/u-boot-2009.11.1/board/atmel/at91sam9261ek/config.mk i modified TEXT_BASE=0x23f00000 to TEXT_BASE=0x27D00000 to reflect the change made for load address of u-boot in SDRAM
when i did the above changes it works for me in u-boot-1.3.4 but when i do
the same u-boot-2009.11.1 it doesnt :( . so may i know is ther any other new thing in new u-boot which im missing? thanks.
warm regards,
Ravi kulkarni.
Signature · 2 lines
View this message in context: http://old.nabble.com/board-doesnt-boot-when-migrating-from-u-boot1.3.4-to-u-boot2009.11.1-tp27400284p27400284.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Quoted 2 lines
My board is based on AT91SAM9261EK. i did a couple of changes to u-boot
which i'm listing below
Quoted 4 lines
1) In the config file /include/configs/at91sam9261ek.h i changed the line
#definePHYS_SDRAM_SIZE0x04000000/* 64 megs */
to
#definePHYS_SDRAM_SIZE0x08000000/* 128 megs */ since i have 128MB
SDRAM >on my board.
Quoted 2 lines
and
#defineCONFIG_SYS_LOAD_ADDR0x22000000/* load
address */
Quoted 3 lines
to
#defineCONFIG_SYS_LOAD_ADDR0x27D00000/* load address */
this is to reflect the change in bootstrap code to copy u-boot to higher
address in SDRAM so tat RFS of >size > 64MB can be copied .
Quoted 1 line
3) and finally in the file
/home/ravikulkarni/denx/u-boot->2009.11.1/board/atmel/at91sam9261ek/config.mk
Quoted 1 line
i modified TEXT_BASE=0x23f00000 to TEXT_BASE=0x27D00000 to reflect the
change made for load >address of u-boot in SDRAM
To make the story short .. were the above changes correct for new u-boot?
if not
what changes i have to a) accomodate 128MB SDRAM instead of 64MB which
comes with AT91SAM9261EK b) to copy RFS size > 64MB . any help
from AT91 users ?
warm regards,
Ravi Kulkarni.
Signature · 2 lines
View this message in context: http://old.nabble.com/board-doesnt-boot-when-migrating-from-u-boot1.3.4-to-u-boot2009.11.1-tp27400284p27409310.html Sent from the Uboot - Users mailing list archive at Nabble.com.