u-boot kernel parameters
Hi all,
I have an ocotea board, the denx latest 2.6 and 2.4 kernel and u-boot 1.1.4.
I downloaded everything from Wolfgang's ftp site and followed the instructions by the letter. I tftp into memory (at 100000) and bootm my kernels. I successfully boot linux 2.6 (2.6.14-rc3) on this board but kernel 2.4 (2.4.25) wont take off.
This is what 2.4 gives me:
(I added early serial messages for clarity)
## Booting image at 00100000 ...
Image Name: Linux-2.4.25 Created: 2006-02-07 2:25:05 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 628718 Bytes = 614 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
id mach(): done
MMU:enter
MMU:hw init
MMU:mapin
MMU:mapin_ram done
MMU:setio
MMU:exitsetup_arch: entersetup_arch: bootmem
arch: exit
arch: exit 2
Anyone has an idea what could be wrong?
--
View this message in context: http://www.nabble.com/u-boot-kernel-parameters-t1077794.html#a2806589
Sent from the Uboot - Users forum at Nabble.com.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20060207/c192f717/attachment.htm
You've entered the dark nether region of console-less portion of the bootup code WAY before the Linux console driver is installed... and it stop somewhere OR merrily went on its way to Linux bootup WITHOUT a console.
Once it switched from old (usually flat) memory model to virtual memory (MMU), all bets are off. Couple of ways to shine a light where the cockroaches are, are to try the following:
1. Pass a boot command line 'console=/dev/ttyS0' from your bootloader or have it compiled in via 'make menuconfig' Check your custom serial driver for the exact TTY device template name (i.e., /dev/ttl0, /dev/ttyAS0).
2. Another way to see what is going on is to flip on the CONFIG_TEXT_CONSOLE_DEBUG and insert MANY ppc_md.progress() calls AFTER the debug console is initialized in arch/ppc/kernel/ppc4xx_setup.c
3. Put a Linux boot command line of 'kgdb' with CONFIG_KGDB to evoke a hardware break and then use hardware debuggerto step through the Linux bootup sequence.
4. Make heavy use of on-board LED indicators by calling ioremap() and poking your virtualized hardware register location to flip on the LED indicators.
Anyway you cut, slice or dice it, this effort will require LOTS of recompile, relink, reload and re-run will be required to 'normalize' a new board bring-up.
Good Luck
S. Egbert
Quoted 30 lines · Bizzu (sent by Nabble.com)
Hi all,
I have an ocotea board, the denx latest 2.6 and 2.4 kernel and u-boot 1.1.4.
I downloaded everything from Wolfgang's ftp site and followed the instructions by the letter. I tftp into memory (at 100000) and bootm my kernels. I successfully boot linux 2.6 (2.6.14-rc3) on this board but kernel 2.4 (2.4.25) wont take off.
This is what 2.4 gives me:
(I added early serial messages for clarity)## Booting image at 00100000 ...
Image Name: Linux-2.4.25 Created: 2006-02-07 2:25:05 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 628718 Bytes = 614 kBLoad Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
idmach(): done
MMU:enter
MMU:hw init
MMU:mapin
MMU:mapin_ram done
MMU:setio
MMU:exitsetup_arch: entersetup_arch: bootmem
arch: exit
arch: exit 2Anyone has an idea what could be wrong?
Argh! Somber, isn't it?
I think most of my issues are in the kernel parameters area.
The bootargs, maybe...
I went back to PIBS, just for the heck of it, and same thing happened, the 2.6 boots, the 2.4 doesn't... The later will fail the same exact way on the same exact spot...
Unless there is something wrong with the default Wolfgang's Ocotea config in 2.4...
Thanks for the answer anyway.
Bizzu
Quoted 38 lines · S. Egbert
You've entered the dark nether region of console-less portion of the bootup code WAY before the Linux console driver is installed... and it stop somewhere OR merrily went on its way to Linux bootup WITHOUT a console.
Once it switched from old (usually flat) memory model to virtual memory (MMU), all bets are off. Couple of ways to shine a light where the cockroaches are, are to try the following:
1. Pass a boot command line 'console=/dev/ttyS0' from your bootloader or have it compiled in via 'make menuconfig' Check your custom serial driver for the exact TTY device template name (i.e.,
/dev/ttl0,/dev/ttyAS0).2. Another way to see what is going on is to flip on the
CONFIG_TEXT_CONSOLE_DEBUGand insert MANYppc_md.progress()calls AFTER the debug console is initialized inarch/ppc/kernel/ppc4xx_setup.c3. Put a Linux boot command line of 'kgdb' with
CONFIG_KGDBto evoke a hardware break and then use hardware debuggerto step through the Linux bootup sequence.4. Make heavy use of on-board LED indicators by calling
ioremap()and poking your virtualized hardware register location to flip on the LED indicators.Anyway you cut, slice or dice it, this effort will require LOTS of recompile, relink, reload and re-run will be required to 'normalize' a new board bring-up.
Good Luck
S. Egbert
Bizzu (sent by Nabble.com) wrote:
Quoted 36 lines
Quoted 2 lines
Hi all,
I have an ocotea board, the denx latest 2.6 and 2.4 kernel and u-boot1.1.4.
Quoted 1 line
I downloaded everything from Wolfgang's ftp site and followed the
instructions by the letter. I tftp into memory (at 100000) and bootm my kernels.
Quoted 1 line
I successfully boot linux 2.6 (2.6.14-rc3) on this board but kernel 2.4(
2.4.25) wont take off.
Quoted 26 lines
This is what 2.4 gives me:
(I added early serial messages for clarity)## Booting image at 00100000 ...
Image Name: Linux-2.4.25 Created: 2006-02-07 2:25:05 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 628718 Bytes = 614 kBLoad Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
idmach(): done
MMU:enter
MMU:hw init
MMU:mapin
MMU:mapin_ram done
MMU:setio
MMU:exitsetup_arch: entersetup_arch: bootmem
arch: exit
arch: exit 2Anyone has an idea what could be wrong?
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20060207/5df642df/attachment.htm
Quoted 5 lines · In message <[email protected]> you wrote:
I have an ocotea board, the denx latest 2.6 and 2.4 kernel and u-boot 1.1.4.
I downloaded everything from Wolfgang's ftp site and followed the instructions by the letter. I tftp into memory (at 100000) and bootm my kernels. I successfully boot linux 2.6 (2.6.14-rc3) on this board but kernel 2.4 (2.4.25) wont take off.
This is what 2.4 gives me:
The documentation is based on the 2.6 kernel, and this is all what we support.
Quoted 4 lines
------=_Part_11010_24584557.1139336071121
Content-Type: text/html; charset=us-ascii
Content-Transfer-Encoding: 7bit
Please never post HTML to this list!!
Best regards,
Wolfgang Denk
Signature · 4 lines
Software Engineering: Embedded and Realtime Systems, Embedded Linux Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Cigarette, n.: A fire at one end, a fool at the other, and a bit of tobacco in between.
Quoted 5 lines · In message <[email protected]> you wrote:
1. Pass a boot command line 'console=/dev/ttyS0' from your bootloader or have it compiled in via 'make menuconfig' Check your custom serial driver for the exact TTY device template name (i.e.,
/dev/ttl0,/dev/ttyAS0).
Alternatively, try using a post mortem dump of the lug buffer to see what might have been prited to the console buffer. See the FAQ for details.
Quoted 3 lines
4. Make heavy use of on-board LED indicators by calling
ioremap()and poking your virtualized hardware register location to flip on the LED indicators.
I strongly recommend *against* doing this, at least unless you know *exactly* what you are doing (and then you don't need this because you will use a BDI2000 anyway). I've seen to many reports of "Linux crashes when enabling the MMU" that were cause by exactly such attempts.
Best regards,
Wolfgang Denk
Signature · 5 lines
Software Engineering: Embedded and Realtime Systems, Embedded Linux Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Another war ... must it always be so? How many comrades have we lost in this way? ... Obedience. Duty. Death, and more death ... -- Romulan Commander, "Balance of Terror", stardate 1709.2
Quoted 3 lines · In message <[email protected]> you…
Unless there is something wrong with the default Wolfgang's Ocotea config in 2.4...
There's nothing wrong with it. It just doesn't support U-Boot. Nobody ever claimed it would.
Best regards,
Wolfgang Denk
Signature · 3 lines
Software Engineering: Embedded and Realtime Systems, Embedded Linux Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Of all the things I've lost, I miss my mind the most.
I understood the contrary when I read the denx.com news page:
"DENX will continue to support our Linux 2.4 kernel, too. " My mistake then...
What should work then?
Quoted 17 lines · Wolfgang Denk
Quoted 3 lines · In message <[email protected]> you…
Unless there is something wrong with the default Wolfgang's Ocotea config in 2.4...
There's nothing wrong with it. It just doesn't support U-Boot. Nobody ever claimed it would.
Best regards,
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Of all the things I've lost, I miss my mind the most.
Quoted 1 line · Wolfgang Denk
In message <[email protected]> you
Quoted 5 lines · wrote:
Quoted 2 lines
Unless there is something wrong with the default Wolfgang's Ocotea config in 2.4...
There's nothing wrong with it. It just doesn't support U-Boot. Nobody ever claimed it would.
Hmmm, I am pretty sure Ocotea linuxppc_2_4_devel worked a few month's ago (with U-Boot of course). I will give it a try tomorrow and let you know.
Best regards,
Stefan
Now that's helpful!
Very, very much appreciated
Thanks Stephan
--
View this message in context: http://www.nabble.com/u-boot-kernel-parameters-t1077794.html#a2811306
Sent from the Uboot - Users forum at Nabble.com.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20060207/affe88f1/attachment.htm
Wolfgang,
thanks for reminding of the buffer.
This is its contents:
00151894 : 3c343e4c 696e7578 20766572 73696f6e <4>Linux version001518a4 : 20322e34 2e323520 28767864 6576656c 2.4.25 (vxdevel
001518b4 : 40767864 6576656c 29202867 63632076 @vxdevel) (gcc v 001518c4 : 65727369 6f6e2033 2e342e31 29202332 ersion 3.4.1) #2 001518d4 : 30205475 65204665 62203720 31343a35 0 Tue Feb 7 14:5 001518e4 : 303a3535 20505354 20323030 360a3c34 0:55 PST 2006.<4 001518f4 : 3e6b6764 6220696e 69740a3c 343e4942 >kgdb init.<4>IB 00151904 : 4d204f63 6f746561 20706f72 7420284d M Ocotea port (M 00151914 : 6f6e7461 56697374 6120536f 66747761 ontaVista Softwa 00151924 : 72652c20 496e632e 203c736f 75726365 re, Inc. ).<4 00151944 : 3e4f6e20 6e6f6465 20302074 6f74616c >On node 0 total 00151954 : 70616765 733a2036 35353336 0a3c343e pages: 65536.<4> 00151964 : 7a6f6e65 2830293a 20363535 33362070 zone(0): 65536 p 00151974 : 61676573 2e0a0000 00000000 00000000 ages............ 00151984 : 00000000 00000000 00000000 00000000 ................ 440GX>md 00151994 : 00000000 00000000 00000000 00000000 ................ 001519a4 : 00000000 00000000 00000000 00000000 ................ 001519b4 : 00000000 00000000 00000000 00000000 ................ 001519c4 : 00000000 00000000 00000000 00000000 ................ 001519d4 : 00000000 00000000 00000000 00000000 ................ 001519e4 : 00000000 00000000 00000000 00000000 ................ 001519f4 : 00000000 00000000 00000000 00000000 ................ 00151a04 : 00000000 00000000 00000000 00000000 ................ 00151a14 : 00000000 00000000 00000000 00000000 ................ 00151a24 : 00000000 00000000 00000000 00000000 ................ 00151a34 : 00000000 00000000 00000000 00000000 ................ 00151a44 : 00000000 00000000 00000000 00000000 ................ 00151a54 : 00000000 00000000 00000000 00000000 ................ 00151a64 : 00000000 00000000 00000000 00000000 ................ 00151a74 : 00000000 00000000 00000000 00000000 ................ 00151a84 : 00000000 00000000 00000000 00000000 ................
Not much I could do with this I am affraid...
--
View this message in context: http://www.nabble.com/u-boot-kernel-parameters-t1077794.html#a2812135
Sent from the Uboot - Users forum at Nabble.com.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20060207/d5bf6c77/attachment.htm
Quoted 2 lines · In message <[email protected]> you…
I understood the contrary when I read the denx.com news page:
"DENX will continue to support our Linux 2.4 kernel, too. "
We continue to support it for the boards we support. Ocotea is not a board which we claim to support in 2.4. We provide support for all AMCC PowerPC boards in U-Boot and in Linux 2.6.
Quoted 2 lines
My mistake then...
What should work then?
Our 2.6 kernel tree. Please RTFM for details.
Best regards,
Wolfgang Denk
Signature · 4 lines
Software Engineering: Embedded and Realtime Systems, Embedded Linux Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de "When the only tool you have is a hammer, you tend to treat everything as if it were a nail." - Abraham Maslow
Quoted 2 lines · In message <[email protected]> you wrote:
thanks for reminding of the buffer.
:-)
Quoted 6 lines
This is its contents:
00151894 :
3c343e4c696e75782076657273696f6e<4>Linux version001518a4:20322e342e323520287678646576656c2.4.25 (vxdevel001518b4: 407678646576656c29202867 63632076 @vxdevel) (gcc v001518c4: 657273696f6e20332e342e3129202332 ersion 3.4.1) #2
gcc 3.4.1?
Ummm... try building with another toolchain (like ELDK :-) Not sure that it will help, but it might.
Best regards,
Wolfgang Denk
Signature · 5 lines
Software Engineering: Embedded and Realtime Systems, Embedded Linux Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Here is an Appalachian version of management's answer to those who are concerned with the fate of the project: "Don't worry about the mule. Just load the wagon." - Mike Dennison's hillbilly uncle
Quoted 11 lines
Quoted 4 lines
4. Make heavy use of on-board LED indicators by calling
ioremap()and poking your virtualized hardware register location to flip on the LED indicators.I strongly recommend *against* doing this, at least unless you know *exactly* what you are doing (and then you don't need this because you will use a BDI2000 anyway). I've seen to many reports of "Linux crashes when enabling the MMU" that were cause by exactly such attempts.
Oh yeah... I totally agreed on your recommendation. But when one is located FAR FAR AWAY from the cushy software laboratory and without a hardware debugger, I have find this technique extremely useful in very DARK, DARK circumstances.
Another time, I had to bring-up a custom board that is totally devoid of inputs/output interface (as those interfaces were still under HW development), this LED method saved my bacon as I SLOWLY and PAINFULLY integrate Xilinx UARTLITE driver (if one is extremely careful about setting aside a TLB region JUST for that purpose.
Alright, alright.... Let us call this LED indicators, a 'poor man's' debugger. Desperate acts calls for desperate measure.
Quoted 2 lines · Stefan Roese
Hmmm, I am pretty sure Ocotea
linuxppc_2_4_develworked a few month's ago (with U-Boot of course). I will give it a try tomorrow and let you know.
As it seems the current version doesn't compile for ocotea:
make[4]: Entering directory `/chroot/server/home/stefan/git/linuxppc_2_4_devel/drivers/net/ibm_emac' ppc_4xx-gcc -D__KERNEL__ -I/chroot/server/home/stefan/git/linuxppc_2_4_devel/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -fomit-frame-pointer -I/chroot/server/home/stefan/git/linuxppc_2_4_devel/arch/ppc -fsigned-char -msoft-float -pipe -ffixed-r2 -Wno-uninitialized -mmultiple -mstring
-Wa,-m405 -nostdinc
-I /opt/eldk-3.1.1/usr/lib/gcc-lib/ppc-linux/3.3.3/include -DKBUILD_BASENAME=ibm_ocp_enet -c -o ibm_ocp_enet.o ibm_ocp_enet.c ibm_ocp_enet.c:158: error: parse error before "__res" ibm_ocp_enet.c:158: warning: type defaults to int' in declaration of __res' ibm_ocp_enet.c:158: warning: data definition has no type or storage class ibm_ocp_enet.c: In function `emac_init':
ibm_ocp_enet.c:1981: error: `bd_t' undeclared (first use in this function) ibm_ocp_enet.c:1981: error: (Each undeclared identifier is reported only once ibm_ocp_enet.c:1981: error: for each function it appears in.) ibm_ocp_enet.c:1981: error: `bd' undeclared (first use in this function) make[4]: *** [ibm_ocp_enet.o] Error 1
If you don't get this error, your linuxppc_2_4_devel version is outdated. With this small patch below this is fixed and the ocotea boots again:
71a72
Quoted 1 line
#include "
asm/ppcboot.h" /* test-only: ocotea build */
## Booting image at 00200000 ...
Image Name: Linux-2.4.25 Created: 2006-02-08 5:44:06 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 649445 Bytes = 634.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.25 (stefan at ubuntu) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3.3-9)) #1 Wed Feb 8 06:41:37 CET 2006
IBM Ocotea port (MontaVista Software, Inc. <[email protected]>) On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=192.168.1.1:/opt/eldk/ppc_4xx ip=192.168.80.2:192.168.1.1::255.255.0.0:ocotea:eth0:off panic=1 console=ttyS0,115200
Calibrating delay loop... 799.53 BogoMIPS
Memory: 257000k available (976k kernel code, 320k data, 232k init, 0k highmem) Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode cache hash table entries: 16384 (order: 5, 131072 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket
Starting kswapd
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xfdfea200 (irq = 0) is a 16550A
ttyS01 at 0xfdfe9300 (irq = 1) is a 16550A
Generic RTC Driver v1.07
emac: IBM OCP EMAC Ethernet driver, version 2.1
Maintained by Benjamin Herrenschmidt <[email protected]>
mal0: Initialized, 8 tx channels, 4 rx channels
zmii0: input 0 in SMII mode
eth0: IBM emac, MAC 00:01:73:01:dd:ac
eth0: Found Generic MII PHY (0x01)
zmii0: input 1 in SMII mode
eth1: IBM emac, MAC 00:01:73:01:dd:ad
eth1: Found Generic MII PHY (0x02)
zmii0: input 2 in SMII mode
rgmii0: input 0 in RGMII mode
eth2: IBM emac, MAC 00:01:73:01:dd:ae
eth2: Found CIS8201 Gigabit Ethernet PHY (0x10)
zmii0: input 3 in SMII mode
rgmii0: input 1 in RGMII mode
eth3: IBM emac, MAC 00:01:73:01:dd:af
eth3: Found CIS8201 Gigabit Ethernet PHY (0x18)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
IP-Config: Complete:
device=eth0, addr=192.168.80.2, mask=255.255.0.0, gw=255.255.255.255,
host=ocotea, domain=, nis-domain=(none),
bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Looking up port of RPC 100003/2 on 192.168.1.1
eth0: Link is Up
eth0: Speed: 100, Full duplex.
Looking up port of RPC 100005/1 on 192.168.1.1
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 232k init
modprobe: modprobe: Can't open dependencies
file /lib/modules/2.4.25/modules.dep (No such file or directory)
INIT: version 2.84 booting
Welcome to DENX Embedded Linux Environment Press 'I' to enter interactive startup.
Building the cache [ OK ]
Mounting proc filesystem: [ OK ] Configuring kernel parameters: [ OK ] Setting clock : Wed Feb 8 08:38:58 MET 2006 [ OK ] Setting hostname ocotea: [ OK ] modprobe: Can't open dependencies file /lib/modules/2.4.25/modules.dep (No such file or directory) Activating swap partitions: [ OK ] Finding module dependencies: depmod: Can't
open /lib/modules/2.4.25/modules.dep for writing
[FAILED]
Checking filesystems
[ OK ]
Mounting local filesystems: [ OK ] Enabling swap space: [ OK ] modprobe: Can't open dependencies file /lib/modules/2.4.25/modules.dep (No such file or directory) INIT: Entering runlevel: 3 Entering non-interactive startup Setting network parameters: [ OK ] Bringing up loopback interface: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Initializing random number generator: [ OK ] Starting portmapper: [ OK ] Mounting NFS filesystems: [ OK ] Mounting other filesystems: [ OK ] Starting xinetd: [ OK ]
ocotea login:
Best regards,
Stefan
Dear Bizzu!
Quoted 1 line · Bizzu (sent by Nabble.com)
[another message in HTML]
PLEASE DO *NOT* SEND MESSAGES IN HTML FORMAT TO THIS MAILING LIST!
I have no problems reading them but there are other people who can't read them. And I don't like it if someone else forces me to read messages with certain font settings.
Regards
Andreas Schweigstill
Signature · 5 lines
Dipl.-Phys. Andreas Schweigstill Schweigstill IT | Embedded Systems Schauenburgerstra?e 116, D-24118 Kiel, Germany Phone: (+49) 431 5606-435, Fax: (+49) 431 5606-436 Mobile: (+49) 171 6921973, Web: http://www.schweigstill.de/
Andreas,
Sorry about the format.
I thought I set it to text only.
If this current one is not then I will have to use another email machine. Please let me know if this is better,
Apologize,
Bizzu
Quoted 22 lines · Andreas Schweigstill
Dear Bizzu!
Quoted 1 line · Bizzu (sent by Nabble.com)
[another message in HTML]
PLEASE DO *NOT* SEND MESSAGES IN HTML FORMAT TO THIS MAILING LIST!
I have no problems reading them but there are other people who can't read them. And I don't like it if someone else forces me to read messages with certain font settings.
Regards
Andreas Schweigstill--
Dipl.-Phys. Andreas Schweigstill
Schweigstill IT | Embedded Systems Schauenburgerstra?e 116, D-24118 Kiel, Germany
Phone: (+49) 431 5606-435, Fax: (+49) 431 5606-436
Mobile: (+49) 171 6921973, Web: http://www.schweigstill.de/
Thanks Stefan,
I will check it out as soon as I get to work.
These are terrific news.
Thanks again.
Bizzu
Quoted 143 lines · Stefan Roese
Quoted 2 lines · Stefan Roese
Hmmm, I am pretty sure Ocotea
linuxppc_2_4_develworked a few month's ago (with U-Boot of course). I will give it a try tomorrow and let you know.As it seems the current version doesn't compile for ocotea:
make[4]: Entering directory `/chroot/server/home/stefan/git/linuxppc_2_4_devel/drivers/net/ibm_emac' ppc_4xx-gcc -D__KERNEL__
(quoted diff) +0
-8-I/chroot/server/home/stefan/git/linuxppc_2_4_devel/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -fomit-frame-pointer -I/chroot/server/home/stefan/git/linuxppc_2_4_devel/arch/ppc -fsigned-char -msoft-float -pipe -ffixed-r2 -Wno-uninitialized -mmultiple -mstring -Wa,-m405 -nostdinc -I /opt/eldk-3.1.1/usr/lib/gcc-lib/ppc-linux/3.3.3/include -DKBUILD_BASENAME=ibm_ocp_enet -c -o ibm_ocp_enet.o ibm_ocp_enet.cibm_ocp_enet.c:158: error: parse error before "
__res" ibm_ocp_enet.c:158: warning: type defaults toint' in declaration of__res' ibm_ocp_enet.c:158: warning: data definition has no type or storage classibm_ocp_enet.c: In function `emac_init':
ibm_ocp_enet.c:1981: error: `bd_t' undeclared (first use in this function) ibm_ocp_enet.c:1981: error: (Each undeclared identifier is reported only once ibm_ocp_enet.c:1981: error: for each function it appears in.) ibm_ocp_enet.c:1981: error: `bd' undeclared (first use in this function) make[4]: *** [ibm_ocp_enet.o] Error 1If you don't get this error, your
linuxppc_2_4_develversion is outdated. With this small patch below this is fixed and the ocotea boots again:71a72
Quoted 1 line
#include "
asm/ppcboot.h" /* test-only: ocotea build */## Booting image at 00200000 ...
Image Name: Linux-2.4.25 Created: 2006-02-08 5:44:06 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 649445 Bytes = 634.2 kBLoad Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.25 (stefan at ubuntu) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3.3-9)) #1 Wed Feb 8 06:41:37 CET 2006
IBM Ocotea port (MontaVista Software, Inc. <[email protected]>) On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=192.168.1.1:/opt/eldk/ppc_4xx ip=192.168.80.2:192.168.1.1::255.255.0.0:ocotea:eth0:off panic=1 console=ttyS0,115200
Calibrating delay loop... 799.53 BogoMIPS
Memory: 257000k available (976k kernel code, 320k data, 232k init, 0k highmem) Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode cache hash table entries: 16384 (order: 5, 131072 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket
Starting kswapd
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) withMANY_PORTSSHARE_IRQSERIAL_PCIenabled
ttyS00 at0xfdfea200(irq = 0) is a 16550A
ttyS01 at0xfdfe9300(irq = 1) is a 16550A
Generic RTC Driver v1.07
emac: IBM OCP EMAC Ethernet driver, version 2.1
Maintained by Benjamin Herrenschmidt <[email protected]>
mal0: Initialized, 8 tx channels, 4 rx channels
zmii0: input 0 in SMII mode
eth0: IBM emac, MAC 00:01:73:01:dd:ac
eth0: Found Generic MII PHY (0x01)
zmii0: input 1 in SMII mode
eth1: IBM emac, MAC 00:01:73:01:dd:ad
eth1: Found Generic MII PHY (0x02)
zmii0: input 2 in SMII mode
rgmii0: input 0 in RGMII mode
eth2: IBM emac, MAC 00:01:73:01:dd:ae
eth2: Found CIS8201 Gigabit Ethernet PHY (0x10)
zmii0: input 3 in SMII mode
rgmii0: input 1 in RGMII mode
eth3: IBM emac, MAC 00:01:73:01:dd:af
eth3: Found CIS8201 Gigabit Ethernet PHY (0x18)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
IP-Config: Complete:device=eth0, addr=192.168.80.2, mask=255.255.0.0, gw=255.255.255.255, host=ocotea, domain=, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Looking up port of RPC 100003/2 on 192.168.1.1
eth0: Link is Up
eth0: Speed: 100, Full duplex.
Looking up port of RPC 100005/1 on 192.168.1.1
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 232k init
modprobe: modprobe: Can't open dependencies
file/lib/modules/2.4.25/modules.dep(No such file or directory)
INIT: version 2.84 booting
Welcome to DENX Embedded Linux Environment Press 'I' to enter interactive startup.
Building the cache [ OK ]Mounting proc filesystem: [ OK ] Configuring kernel parameters: [ OK ] Setting clock : Wed Feb 8 08:38:58 MET 2006 [ OK ] Setting hostname ocotea: [ OK ] modprobe: Can't open dependencies file /lib/modules/2.4.25/modules.dep (No such file or directory) Activating swap partitions: [ OK ] Finding module dependencies: depmod: Can'topen
/lib/modules/2.4.25/modules.depfor writing
[FAILED]
Checking filesystems
[ OK ]Mounting local filesystems: [ OK ] Enabling swap space: [ OK ] modprobe: Can't open dependencies file /lib/modules/2.4.25/modules.dep (No such file or directory) INIT: Entering runlevel: 3 Entering non-interactive startup Setting network parameters: [ OK ] Bringing up loopback interface: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Initializing random number generator: [ OK ] Starting portmapper: [ OK ] Mounting NFS filesystems: [ OK ] Mounting other filesystems: [ OK ] Starting xinetd: [ OK ]ocotea login:
Best regards,
Stefan
Quoted 152 lines · Stefan Roese
Quoted 2 lines · Stefan Roese
Hmmm, I am pretty sure Ocotea
linuxppc_2_4_develworked a few month's ago (with U-Boot of course). I will give it a try tomorrow and let you know.As it seems the current version doesn't compile for ocotea:
make[4]: Entering directory `/chroot/server/home/stefan/git/linuxppc_2_4_devel/drivers/net/ibm_emac' ppc_4xx-gcc -D__KERNEL__
(quoted diff) +0
-8-I/chroot/server/home/stefan/git/linuxppc_2_4_devel/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -fomit-frame-pointer -I/chroot/server/home/stefan/git/linuxppc_2_4_devel/arch/ppc -fsigned-char -msoft-float -pipe -ffixed-r2 -Wno-uninitialized -mmultiple -mstring -Wa,-m405 -nostdinc -I /opt/eldk-3.1.1/usr/lib/gcc-lib/ppc-linux/3.3.3/include -DKBUILD_BASENAME=ibm_ocp_enet -c -o ibm_ocp_enet.o ibm_ocp_enet.cibm_ocp_enet.c:158: error: parse error before "
__res" ibm_ocp_enet.c:158: warning: type defaults toint' in declaration of__res'
ibm_ocp_enet.c:158: warning: data definition has no type or storage classibm_ocp_enet.c: In function `emac_init':
ibm_ocp_enet.c:1981: error: `bd_t' undeclared (first use in this function) ibm_ocp_enet.c:1981: error: (Each undeclared identifier is reported only once
ibm_ocp_enet.c:1981: error: for each function it appears in.) ibm_ocp_enet.c:1981: error: `bd' undeclared (first use in this function) make[4]: *** [ibm_ocp_enet.o] Error 1If you don't get this error, your
linuxppc_2_4_develversion is outdated. With
this small patch below this is fixed and the ocotea boots again:71a72
Quoted 1 line
#include "
asm/ppcboot.h" /* test-only: ocotea build */## Booting image at 00200000 ...
Image Name: Linux-2.4.25 Created: 2006-02-08 5:44:06 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 649445 Bytes = 634.2 kBLoad Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.25 (stefan at ubuntu) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3.3-9)) #1 Wed Feb 8 06:41:37 CET 2006
IBM Ocotea port (MontaVista Software, Inc. < [email protected]>) On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=192.168.1.1:/opt/eldk/ppc_4xx ip=192.168.80.2:192.168.1.1::255.255.0.0:ocotea:eth0:off panic=1 console=ttyS0,115200
Calibrating delay loop... 799.53 BogoMIPS
Memory: 257000k available (976k kernel code, 320k data, 232k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode cache hash table entries: 16384 (order: 5, 131072 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket
Starting kswapd
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) withMANY_PORTSSHARE_IRQSERIAL_PCI
enabled
ttyS00 at0xfdfea200(irq = 0) is a 16550A
ttyS01 at0xfdfe9300(irq = 1) is a 16550A
Generic RTC Driver v1.07
emac: IBM OCP EMAC Ethernet driver, version 2.1
Maintained by Benjamin Herrenschmidt < [email protected]>
mal0: Initialized, 8 tx channels, 4 rx channels
zmii0: input 0 in SMII mode
eth0: IBM emac, MAC 00:01:73:01:dd:ac
eth0: Found Generic MII PHY (0x01)
zmii0: input 1 in SMII mode
eth1: IBM emac, MAC 00:01:73:01:dd:ad
eth1: Found Generic MII PHY (0x02)
zmii0: input 2 in SMII mode
rgmii0: input 0 in RGMII mode
eth2: IBM emac, MAC 00:01:73:01:dd:ae
eth2: Found CIS8201 Gigabit Ethernet PHY (0x10)
zmii0: input 3 in SMII mode
rgmii0: input 1 in RGMII mode
eth3: IBM emac, MAC 00:01:73:01:dd:af
eth3: Found CIS8201 Gigabit Ethernet PHY (0x18)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
IP-Config: Complete:device=eth0, addr=192.168.80.2, mask=255.255.0.0,gw=255.255.255.255,
host=ocotea, domain=, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Looking up port of RPC 100003/2 on 192.168.1.1
eth0: Link is Up
eth0: Speed: 100, Full duplex.
Looking up port of RPC 100005/1 on 192.168.1.1
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 232k init
modprobe: modprobe: Can't open dependencies
file/lib/modules/2.4.25/modules.dep(No such file or directory)
INIT: version 2.84 booting
Welcome to DENX Embedded Linux Environment Press 'I' to enter interactive startup.
Building the cache [ OK ]Mounting proc filesystem: [ OK ] Configuring kernel parameters: [ OK ] Setting clock : Wed Feb 8 08:38:58 MET 2006 [ OK ] Setting hostname ocotea: [ OK ] modprobe: Can't open dependencies file /lib/modules/2.4.25/modules.dep (No such file or directory) Activating swap partitions: [ OK ] Finding module dependencies: depmod: Can'topen
/lib/modules/2.4.25/modules.depfor writing
[FAILED]
Checking filesystems
[ OK ]Mounting local filesystems: [ OK ] Enabling swap space: [ OK ] modprobe: Can't open dependencies file /lib/modules/2.4.25/modules.dep (No such file or directory) INIT: Entering runlevel: 3 Entering non-interactive startup Setting network parameters: [ OK ] Bringing up loopback interface: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Initializing random number generator: [ OK ] Starting portmapper: [ OK ] Mounting NFS filesystems: [ OK ] Mounting other filesystems: [ OK ] Starting xinetd: [ OK ]ocotea login:
Best regards,
Stefan
Quoted 12 lines
-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files
for problems? Stop! Download the new AJAX search engine that makes searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=103432&bid=230486&dat=121642
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users
Stephan,
I followed your tracks and got it to boot as you did.
This is just fantastic!
Danke sch?n!
Bizzu
--
View this message in context: http://www.nabble.com/u-boot-kernel-parameters-t1077794.html#a2823509
Sent from the Uboot - Users forum at Nabble.com.
Dear All,
Now I am working on CIS8201 PHY for RGMII mode, I have modified Reg 23(0x17h) from 0000 to 1300, but CIS8201 doesn't work under RGMII mode, are there other registers I need to set? Please give me your comment. Thanks a lot!
2006/2/8, Tattone Tattone <[email protected]>:
Quoted 169 lines
Thanks Stefan,
I will check it out as soon as I get to work.
These are terrific news.Thanks again.
BizzuQuoted 2 lines · Stefan Roese
Quoted 1 line · Stefan Roese
Hmmm, I am pretty sure Ocotea
linuxppc_2_4_develworked a few month'sago
Quoted 1 line
Quoted 1 line
(with U-Boot of course). I will give it a try tomorrow and let you
know.
Review
Quoted 10 lines
As it seems the current version doesn't compile for ocotea:
make[4]: Entering directory `/chroot/server/home/stefan/git/linuxppc_2_4_devel/drivers/net/ibm_emac' ppc_4xx-gcc -D__KERNEL__
(quoted diff) +0
-4-I/chroot/server/home/stefan/git/linuxppc_2_4_devel/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -fomit-frame-pointer -I/chroot/server/home/stefan/git/linuxppc_2_4_devel/arch/ppc-fsigned-char
Quoted 6 lines
(quoted diff) +0
-4-msoft-float -pipe -ffixed-r2 -Wno-uninitialized -mmultiple -mstring -Wa,-m405 -nostdinc -I /opt/eldk-3.1.1/usr/lib/gcc-lib/ppc-linux/3.3.3/include -DKBUILD_BASENAME=ibm_ocp_enet -c -o ibm_ocp_enet.o ibm_ocp_enet.cibm_ocp_enet.c:158: error: parse error before "
__res" ibm_ocp_enet.c:158: warning: type defaults to `int' in declaration of`__res'
Quoted 1 line
ibm_ocp_enet.c:158: warning: data definition has no type or storage
class
Quoted 2 lines
ibm_ocp_enet.c: In function `emac_init':
ibm_ocp_enet.c:1981: error: `bd_t' undeclared (first use in thisfunction)
Quoted 1 line
ibm_ocp_enet.c:1981: error: (Each undeclared identifier is reported only
once
Quoted 5 lines
ibm_ocp_enet.c:1981: error: for each function it appears in.) ibm_ocp_enet.c:1981: error: `bd' undeclared (first use in this function) make[4]: *** [ibm_ocp_enet.o] Error 1
If you don't get this error, your
linuxppc_2_4_develversion isoutdated. With
Quoted 10 lines
this small patch below this is fixed and the ocotea boots again:
71a72
Quoted 1 line
#include "
asm/ppcboot.h" /* test-only: ocotea build */## Booting image at 00200000 ...
Image Name: Linux-2.4.25 Created: 2006-02-08 5:44:06 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 649445 Bytes = 634.2 kBQuoted 12 lines
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.25 (stefan at ubuntu) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3.3-9)) #1 Wed Feb 8 06:41:37 CET 2006
IBM Ocotea port (MontaVista Software, Inc. <[email protected]>) On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=192.168.1.1:/opt/eldk/ppc_4xx
Quoted 4 lines
ip=192.168.80.2:192.168.1.1::255.255.0.0:ocotea:eth0:off panic=1 console=ttyS0,115200
Calibrating delay loop... 799.53 BogoMIPS
Memory: 257000k available (976k kernel code, 320k data, 232k init, 0khighmem)
Quoted 5 lines
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode cache hash table entries: 16384 (order: 5, 131072 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Quoted 8 lines
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket
Starting kswapd
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) withMANY_PORTSSHARE_IRQ
SERIAL_PCIQuoted 26 lines
enabled
ttyS00 at0xfdfea200(irq = 0) is a 16550A
ttyS01 at0xfdfe9300(irq = 1) is a 16550A
Generic RTC Driver v1.07
emac: IBM OCP EMAC Ethernet driver, version 2.1 Maintained by Benjamin Herrenschmidt <[email protected]>
mal0: Initialized, 8 tx channels, 4 rx channels
zmii0: input 0 in SMII mode
eth0: IBM emac, MAC 00:01:73:01:dd:ac
eth0: Found Generic MII PHY (0x01)
zmii0: input 1 in SMII mode
eth1: IBM emac, MAC 00:01:73:01:dd:ad
eth1: Found Generic MII PHY (0x02)
zmii0: input 2 in SMII mode
rgmii0: input 0 in RGMII mode
eth2: IBM emac, MAC 00:01:73:01:dd:ae
eth2: Found CIS8201 Gigabit Ethernet PHY (0x10)
zmii0: input 3 in SMII mode
rgmii0: input 1 in RGMII mode
eth3: IBM emac, MAC 00:01:73:01:dd:af
eth3: Found CIS8201 Gigabit Ethernet PHY (0x18)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
IP-Config: Complete:Quoted 1 line
device=eth0, addr=192.168.80.2, mask=255.255.0.0, gw=255.255.255.255,
Quoted 15 lines
host=ocotea, domain=, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Looking up port of RPC 100003/2 on 192.168.1.1
eth0: Link is Up
eth0: Speed: 100, Full duplex.
Looking up port of RPC 100005/1 on 192.168.1.1
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 232k init
modprobe: modprobe: Can't open dependencies
file/lib/modules/2.4.25/modules.dep(No such file or directory)
INIT: version 2.84 booting
Welcome to DENX Embedded Linux Environment Press 'I' to enter interactive startup.
Building the cache [ OK ]Quoted 5 lines
Mounting proc filesystem: [ OK ] Configuring kernel parameters: [ OK ] Setting clock : Wed Feb 8 08:38:58 MET 2006 [ OK ] Setting hostname ocotea: [ OK ] modprobe: Can't open dependencies file /lib/modules/2.4.25/modules.dep(No
Quoted 10 lines
such file or directory)
Activating swap partitions: [ OK ] Finding module dependencies: depmod: Can'topen
/lib/modules/2.4.25/modules.depfor writing
[FAILED]
Checking filesystems
[ OK ]Mounting local filesystems: [ OK ] Enabling swap space: [ OK ] modprobe: Can't open dependencies file /lib/modules/2.4.25/modules.dep(No
Quoted 13 lines
such file or directory)
INIT: Entering runlevel: 3
Entering non-interactive startupSetting network parameters: [ OK ] Bringing up loopback interface: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Initializing random number generator: [ OK ] Starting portmapper: [ OK ] Mounting NFS filesystems: [ OK ] Mounting other filesystems: [ OK ] Starting xinetd: [ OK ]Quoted 6 lines
ocotea login:
Best regards,
Stefan
Quoted 11 lines
-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files
for problems? Stop! Download the new AJAX search engine that makes searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://sel.as-us.falkag.net/sel?cmdlnk&kid3432&bid#0486&dat1642
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20060215/cdfa6961/attachment.htm
Quoted 7 lines · Simon Yang
Dear All,
Now I am working on CIS8201 PHY for RGMII mode, I have modified Reg 23(0x17h) from 0000 to 1300, but CIS8201 doesn't work under RGMII mode, are there other registers I need to set? Please give me your comment. Thanks a lot!
Simon:
If you're using the ocotea, phy reg 0x17 should be written with 0x1000 for rgmii mode, not 0x1300. 0x300 enables clock skewing for boards with short etch, like the Sandburst Metrobox and Karef boards. The ocotea has full length etch and doesn't (or rather should not) use clock skewing.
Das U-Boot current source should 'just work' on the ocotea board.
(I can't verify the current source as I haven't done a git sync since Stefan merged/fixed the 4xx files, too many time constraints here at work, so I'm working with an 'older' tree).
-travis
Das U-Boot current source should 'just work' on the ocotea board.
Travis,
I am not sure I understand the question from Simon entirely but:
I am booting the 2.4 head with the u-boot head on Ocotea.
U-boot is in flash and linux in flash or tftp.
All devices on the board accounted for.
Bizzu
--
View this message in context: http://www.nabble.com/u-boot-kernel-parameters-t1077794.html#a2956582
Sent from the Uboot - Users forum at Nabble.com.
Hi Travis,
Thanks for your reply. I still have a question, for rgmii mode the bits 11:9 of phy reg 0x17 should be 001 which means the I/O pin operate from 2.5V, default is 3.3V if the value of bits 11:9 is 000, so whether I should set reg 0x17 to 1200.
The cpu we use is MPC8349E, I set the reg ECNTRL to 0x00001010 , I can meature the signals on TSEC1_GTX_CLK, Tx_EN and Tx_D[0:3], the RGMII should operate on 2.5v but the voltage I meature on Tx_D is 3.3v , so there is a problem that the value of reg SICRH(in local memory offset is 0x118) is always 00000002(GMII mode and RGMII mode), but in the datasheet of MPC8349E the bits 30 and 31of reg SICRH (TSOBI1 and TSOBI2) controls the output buffer impedance of the TSEC1and TSEC2 output signals, so I think the value I get is not what I expected. Cany anybody tell me how the reg SICRH get this value? Seems SICRH only use in /cpu/mpc83xx/cpu_init.c file. Thanks a lot!
2006/2/15, Travis B. Sawyer <[email protected]>:
Quoted 16 lines
Quoted 7 lines · Simon Yang
Dear All,
Now I am working on CIS8201 PHY for RGMII mode, I have modified Reg 23(0x17h) from 0000 to 1300, but CIS8201 doesn't work under RGMII mode, are there other registers I need to set? Please give me your comment. Thanks a lot!
Simon:
If you're using the ocotea, phy reg0x17should be written with0x1000for rgmii mode, not0x1300.0x300enables clock skewing for boards with short etch, like the Sandburst Metrobox and Karef boards. The ocotea has full length etch and doesn't (or rather should not) use clock skewing.
Quoted 9 lines
Das U-Boot current source should 'just work' on the ocotea board.
(I can't verify the current source as I haven't done a git sync since Stefan merged/fixed the 4xx files, too many time constraints here at work, so I'm working with an 'older' tree).
-travis
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20060217/3c5a4b9c/attachment.htm