u-boot 2010 - devkit8000 issue
Hello
I have a clone of beagleboard (devkit8000) I update the u-boot from 2009-11 to 2010 version. I use a set of scripts to boot based on autoboot method. The thing is, now I can not boot and hangs at kernel loading. I've tested several kernels provided by manufacturer, linux-omap-2.6, some other from git:/gitorious/devkit8000 and all of them end like:
## Booting kernel from Legacy Image at 82000000 ...
...
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
hangs here
and some others
Verifying Checksum ... OK
Loading Kernel Image ...
hangs here.
these are my u-boot environment variables. Some of you can give a clue ? I ve tested almost everything.
bootdelay=3
baudrate=115200
loadaddr=0x82000000
console=ttyS2,115200n8
vram=12M
dvimode=1024x768MR-16 at 60
defaultdisplay=dvi
nfsopts=hard,tcp,rsize=65536,wsize=65536
commonargs=setenv bootargs console=${console} vram=${vram} omapfb.mode=dvi:${dvimode} omapdss.def_disp=${defaultdisplay} mmcargs=run commonargs; setenv bootargs ${bootargs} root=/dev/mmcblk0p2 ${kernelopts}
nandargs=run commonargs; setenv bootargs ${bootargs} omapfb.mode=dvi:${dvimode} omapdss.def_disp=${defaultdisplay} root=/dev/mtdblock4 rootfstype=jffs2 ${kernel}
netargs=run commonargs; setenv bootargs ${bootargs} root=/dev/nfs nfsroot=${serverip}:${rootpath},${nfsopts} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${} loadbootscript=fatload mmc 0 ${loadaddr} boot.scr bootscript=echo Running bootscript from mmc ...; source ${loadaddr} loaduimage=fatload mmc 0 ${loadaddr} uImage
eraseenv=nand unlock 0x260000 0x20000; nand erase 0x260000 0x20000 mmcboot=echo Booting from mmc ...; run mmcargs; bootm ${loadaddr} nandboot=echo Booting from nand ...; run nandargs; nand read ${loadaddr} 280000 400000; bootm ${loadaddr}
netboot=echo Booting from network ...; dhcp ${loadaddr}; run netargs; bootm ${loadaddr}
autoboot=if mmc init 0; then if run loadbootscript; then run bootscript; else if run loaduimage; then run mmcboot; else run nandboot; fi; fi; else run nandboot;i
ethaddr=02:fa:19:01:f0:1e dieid#=6db2000400000000040365fa1901f01e
ethact=dm9000
bootargs=console=ttyS2,115200n8 console=tty0 root=/dev/mmcblk0p2 rw rootwait bootargs_back=console=ttyS2,115200n8 console=tty0 root=/dev/mmcblk0p2 rw rootwait
bootcmd=mmc init;fatload mmc1 0 0x82000000 uImage.bin;bootm 0x82000000 stdin=serial
stdout=serial
stderr=serial
kernelopts=rw
Signature · 2 lines
View this message in context: http://old.nabble.com/u-boot-2010---devkit8000-issue-tp28866288p28866288.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Hello,
the u-boot and the linux-kernel from the TimLL cd are patched with an unofficial machine identifier. They are not working with any other of your sources. You need to update both, u-boot and linux-kernel. Can you write me, which u-boot and linux-kernel version you are using?
Thomas
Quoted 79 lines · JaimeR
Hello
I have a clone of beagleboard (devkit8000) I update the u-boot from 2009-11 to 2010 version. I use a set of scripts to boot based on autoboot method. The thing is, now I can not boot and hangs at kernel loading. I've tested several kernels provided by manufacturer, linux-omap-2.6, some other from git:/gitorious/devkit8000 and all of them end like:
## Booting kernel from Legacy Image at 82000000 ...
...
? Verifying Checksum ... OK
? Loading Kernel Image ... OK
OKStarting kernel ...
hangs here
and some others
? Verifying Checksum ... OK
? Loading Kernel Image ...hangs here.
these are my u-boot environment variables. Some of you can give a clue ? I ve tested almost everything.
bootdelay=3
baudrate=115200
loadaddr=0x82000000
console=ttyS2,115200n8
vram=12M
dvimode=1024x768MR-16 at 60
defaultdisplay=dvi
nfsopts=hard,tcp,rsize=65536,wsize=65536
commonargs=setenv bootargs console=${console} vram=${vram}
omapfb.mode=dvi:${dvimode} omapdss.def_disp=${defaultdisplay}
mmcargs=run commonargs; setenv bootargs ${bootargs} root=/dev/mmcblk0p2
${kernelopts}
nandargs=run commonargs; setenv bootargs ${bootargs}
omapfb.mode=dvi:${dvimode} omapdss.def_disp=${defaultdisplay}
root=/dev/mtdblock4 rootfstype=jffs2 ${kernel}
netargs=run commonargs; setenv bootargs ${bootargs} root=/dev/nfs nfsroot=${serverip}:${rootpath},${nfsopts} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${}
loadbootscript=fatload mmc 0 ${loadaddr} boot.scr
bootscript=echo Running bootscript from mmc ...; source ${loadaddr}
loaduimage=fatload mmc 0 ${loadaddr} uImage
eraseenv=nand unlock0x2600000x20000; nand erase0x2600000x20000
mmcboot=echo Booting from mmc ...; run mmcargs; bootm ${loadaddr}
nandboot=echo Booting from nand ...; run nandargs; nand read ${loadaddr}
280000 400000; bootm ${loadaddr}
netboot=echo Booting from network ...; dhcp ${loadaddr}; run netargs; bootm
${loadaddr}
autoboot=if mmc init 0; then if run loadbootscript; then run bootscript;
else if run loaduimage; then run mmcboot; else run nandboot; fi; fi; else
run nandboot;i
ethaddr=02:fa:19:01:f0:1e
dieid#=6db2000400000000040365fa1901f01e
ethact=dm9000
bootargs=console=ttyS2,115200n8 console=tty0 root=/dev/mmcblk0p2 rw rootwait bootargs_back=console=ttyS2,115200n8 console=tty0 root=/dev/mmcblk0p2 rw
rootwait
bootcmd=mmc init;fatload mmc1 00x82000000uImage.bin;bootm0x82000000
stdin=serial
stdout=serial
stderr=serial
kernelopts=rw
--
View this message in context: http://old.nabble.com/u-boot-2010---devkit8000-issue-tp28866288p28866288.html
Sent from the Uboot - Users mailing list archive at Nabble.com._______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
I have a similar issue: I have a beagleboard rev C4 and I'm trying to use a custom kernel instead of Angstrom. I downloaded the last u-boot using git from git://gitorious.org/beagleboard-validation/u-boot.git
I compiled this u-boot and then I compiled the MontaVista kernel
(http://www.beagleboard.org/~arago/esc-boston-2009/mvista/beaglekernel24.v1.tar.bz2).
Thus I obtained a uImage.
I copied MLO, u-boot.bin and uImage into a SD card and tryed to boot from this:
...
OMAP3 beagleboard.org # mmc init
mmc1 is available
OMAP3 beagleboard.org # fatload mmc 0:1 0x82000000 uimage reading uimage
1568464 bytes read
OMAP3 beagleboard.org # bootm 0x82000000
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-2.6.24_mvl5024-beagle_ESC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1568400 Bytes = 1.5 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ...
----HANGS HERE----
Please help me, I'm trying everything but nothing works....
Quoted 101 lines · Thomas Weber-16 wrote:
Hello,
the u-boot and the linux-kernel from the TimLL cd are patched with an unofficial machine identifier. They are not working with any other of your sources. You need to update both, u-boot and linux-kernel. Can you write me, which u-boot and linux-kernel version you are using?
Thomas
Quoted 79 lines · JaimeR
Hello
I have a clone of beagleboard (devkit8000) I update the u-boot from 2009-11
to 2010 version. I use a set of scripts to boot based on autoboot method. The thing is, now I can not boot and hangs at kernel loading. I've tested several kernels provided by manufacturer, linux-omap-2.6, some other from git:/gitorious/devkit8000 and all of them end like:## Booting kernel from Legacy Image at 82000000 ...
...
? Verifying Checksum ... OK
? Loading Kernel Image ... OK
OKStarting kernel ...
hangs here
and some others
? Verifying Checksum ... OK
? Loading Kernel Image ...hangs here.
these are my u-boot environment variables. Some of you can give a clue ? I
ve tested almost everything.bootdelay=3
baudrate=115200
loadaddr=0x82000000
console=ttyS2,115200n8
vram=12M
dvimode=1024x768MR-16 at 60
defaultdisplay=dvi
nfsopts=hard,tcp,rsize=65536,wsize=65536
commonargs=setenv bootargs console=${console} vram=${vram} omapfb.mode=dvi:${dvimode} omapdss.def_disp=${defaultdisplay} mmcargs=run commonargs; setenv bootargs ${bootargs} root=/dev/mmcblk0p2 ${kernelopts}
nandargs=run commonargs; setenv bootargs ${bootargs} omapfb.mode=dvi:${dvimode} omapdss.def_disp=${defaultdisplay} root=/dev/mtdblock4 rootfstype=jffs2 ${kernel}
netargs=run commonargs; setenv bootargs ${bootargs} root=/dev/nfs nfsroot=${serverip}:${rootpath},${nfsopts} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${} loadbootscript=fatload mmc 0 ${loadaddr} boot.scr bootscript=echo Running bootscript from mmc ...; source ${loadaddr} loaduimage=fatload mmc 0 ${loadaddr} uImage
eraseenv=nand unlock0x2600000x20000; nand erase0x2600000x20000mmcboot=echo Booting from mmc ...; run mmcargs; bootm ${loadaddr} nandboot=echo Booting from nand ...; run nandargs; nand read ${loadaddr} 280000 400000; bootm ${loadaddr}
netboot=echo Booting from network ...; dhcp ${loadaddr}; run netargs; bootm
${loadaddr}
autoboot=if mmc init 0; then if run loadbootscript; then run bootscript; else if run loaduimage; then run mmcboot; else run nandboot; fi; fi; else run nandboot;i
ethaddr=02:fa:19:01:f0:1e dieid#=6db2000400000000040365fa1901f01e
ethact=dm9000
bootargs=console=ttyS2,115200n8 console=tty0 root=/dev/mmcblk0p2 rw rootwait
bootargs_back=console=ttyS2,115200n8 console=tty0 root=/dev/mmcblk0p2 rw rootwait
bootcmd=mmc init;fatload mmc1 00x82000000uImage.bin;bootm0x82000000stdin=serial
stdout=serial
stderr=serial
kernelopts=rw
--
View this message in context:
http://old.nabble.com/u-boot-2010---devkit8000-issue-tp28866288p28866288.html
Sent from the Uboot - Users mailing list archive at Nabble.com.Quoted 5 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Signature · 2 lines
View this message in context: http://old.nabble.com/u-boot-2010---devkit8000-issue-tp28866288p29642184.html Sent from the Uboot - Users mailing list archive at Nabble.com.