Skip to contentSkip to conversation

Front speakers doesn't work in multichannel output, regression in ALC888

DISCUSSION Łukasz Wojniłowicz 4 participants 16 messages May 2, 2015 – Jul 11, 2015 14 messages not in the archive Sound

lore
Share & tools
lore
#0 lore raw

Hi all,

My problem is that when I set channel output to "Analog output surround 5.1" (or 2.1 or 4.1), I hear no sound in front speakers, but in case of 5.1 or 4.1 I can hear sound in rear speakers. I use kernel 3.19.5 and it didn't happen in earlier kernels that is 3.18 and in 3.17 for sure.

My configuration is:
OS: Fedora 21 64 bit
SoundCard: ALC888
Model name: acer-aspire-4930g
Laptop: Acer Aspire 5930g
Speakers: external 5.1 with 3 jacks
Sound channel configuration module is standard configuration module from KDE.

Additional info:
1) When channel output is 5.1 and I unplug green jack and leave two others jacks connected then I can hear sound in laptop internal speakers.
2) Earlier (kernel 3.18 and 3.17) I didn't have possibility to choose 2.1 configuration and additionally to 4.1 configuration I could also choose 4.0 configuration.

Thanks for looking into problem.

Cheers
LW

#1 lore raw

At Sat, 02 May 2015 07:42:27 +0200,

Quoted 16 lines · Łukasz Wojniłowicz

Hi all,

My problem is that when I set channel output to "Analog output surround 5.1" (or 2.1 or 4.1), I hear no sound in front speakers, but in case of 5.1 or 4.1 I can hear sound in rear speakers. I use kernel 3.19.5 and it didn't happen in earlier kernels that is 3.18 and in 3.17 for sure.

My configuration is:
OS: Fedora 21 64 bit
SoundCard: ALC888
Model name: acer-aspire-4930g
Laptop: Acer Aspire 5930g
Speakers: external 5.1 with 3 jacks
Sound channel configuration module is standard configuration module from KDE.

Quoted 8 lines

Additional info:
1) When channel output is 5.1 and I unplug green jack and leave two others jacks connected then I can hear sound in laptop internal speakers.
2) Earlier (kernel 3.18 and 3.17) I didn't have possibility to choose 2.1 configuration and additionally to 4.1 configuration I could also choose 4.0 configuration.

Thanks for looking into problem.

I don't remember any relevant change... Could you try git bisect?

thanks,

Takashi
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

#2 lore raw
In reply to Łukasz Wojniłowicz
Quoted 17 lines

My problem is that when I set channel output to "Analog output surround 5.1"
(or 2.1 or 4.1), I hear no sound in front speakers, but in case of 5.1 or 4.1
I can hear sound in rear speakers. I use kernel 3.19.5 and it didn't happen in
earlier kernels that is 3.18 and in 3.17 for sure.

My configuration is:
OS: Fedora 21 64 bit
SoundCard: ALC888
Model name: acer-aspire-4930g
Laptop: Acer Aspire 5930g
Speakers: external 5.1 with 3 jacks
Sound channel configuration module is standard configuration module from KDE.

Quoted 8 lines

Additional info:
1) When channel output is 5.1 and I unplug green jack and leave two others jacks connected then I can hear sound in laptop internal speakers.
2) Earlier (kernel 3.18 and 3.17) I didn't have possibility to choose 2.1 configuration and additionally to 4.1 configuration I could also choose 4.0 configuration.

You need to switch "Channel mode" to "6 ch" if you need to use external

5.1 speakers since you have 5.1 internal speakers

this change pin-ctl of headphone jack, mic jack and line in to OUT

post the output of alsa-info.sh

#4 lore raw
In reply to a message not in the archive
Quoted 1 line
Quoted 1 line
Quoted 1 line

My problem is that when I set channel output to "Analog output

surround

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

5.1"
(or 2.1 or 4.1), I hear no sound in front speakers, but in case of

5.1 or

Quoted 1 line
Quoted 1 line
Quoted 1 line

4.1

You need pulseaudio lfe-filter for 2.1

http://cgit.freedesktop.org/pulseaudio/pulseaudio/log/?qt=grep&q=lfe-filter

do you mean surround21 need 6 channel instead of channels with 5.1 internal /external speaker ?

http://git.alsa-project.org/?p=alsa-lib.git;a=commitdiff;h=48f1b308cc66152eb6db66742dd0d08d888cda8d;hp=5c4cd46810cef8850b037fca9e38ffd43b0bff22

Quoted 11 lines
Quoted 11 lines
Quoted 11 lines

I can hear sound in rear speakers. I use kernel 3.19.5 and it didn't happen in
earlier kernels that is 3.18 and in 3.17 for sure.

My configuration is:
OS: Fedora 21 64 bit
SoundCard: ALC888
Model name: acer-aspire-4930g
Laptop: Acer Aspire 5930g
Speakers: external 5.1 with 3 jacks
Sound channel configuration module is standard configuration module

from

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

KDE.

Additional info:
1) When channel output is 5.1 and I unplug green jack and leave two

others

Quoted 1 line
Quoted 1 line
Quoted 1 line

jacks connected then I can hear sound in laptop internal speakers.

auto mute only check headphone jack or line out jack but not those retasked mio jacks

Quoted 1 line
Quoted 1 line
Quoted 1 line

2) Earlier (kernel 3.18 and 3.17) I didn't have possibility to choose

2.1

Quoted 1 line
Quoted 1 line
Quoted 1 line

configuration and additionally to 4.1 configuration I could also

choose

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

4.0
configuration.

You need to switch "Channel mode" to "6 ch" if you need to use

external

Quoted 8 lines
Quoted 6 lines

5.1 speakers since you have 5.1 internal speakers

this change pin-ctl of headphone jack, mic jack and line in to OUT

post the output of alsa-info.sh

I always switched to "6 ch" through alsamixer. It always worked as

expected,

Quoted 5 lines

but recently I've got problems with it so it regressed somewhere.

My alsa-info.sh with "6 ch" set through alsamixer and "Analog output

surround

Quoted 4 lines

5.1 + Analog input stereo" set through KDE configuration module.
http://www.alsa-project.org/db/?f=ff3f5a1f7f3e4662c3fa9bcf0158474a076b4cc4

With that I hear all channels except front left and front right.

autoconfig for ALC888: line_outs=3 (0x14/0x17/0x16/0x0/0x0) type:speaker
speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
hp_outs=1 (0x15/0x0/0x0/0x0/0x0)
mono: mono_out=0x0
dig-out=0x1e/0x0
inputs:

     Mic=0x18
     Internal Mic=0x12
     Line=0x1a

==> Best config: lo_type=2, wired=1, mio=1
multi_outs = 15/0/0/0 : 2/3/4/0 (type HP)
out path: depth=3 '02:0c:15'
multi_ios(2) = 1a/18 : 3/4
mio path: depth=3 '03:0d:1a'
mio path: depth=3 '04:0e:18'
spk_outs = 14/17/16/0 : 5/25/4/0
spk path: depth=3 '05:0f:14'
spk path: depth=3 '25:26:17'
spk path: depth=3 '04:0e:16'

Node 0x15 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Control: name="Headphone Playback Switch", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Control: name="Front Headphone Jack", index=0, device=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x0001003e: IN OUT HP EAPD Detect Trigger
  EAPD 0x2: EAPD
  Pin Default 0x0221101f: [Jack] HP Out at Ext Front
    Conn = 1/8, Color = Black
    DefAssociation = 0x1, Sequence = 0xf
  Pin-ctls: 0xc0: OUT HP
  Unsolicited: tag=01, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26

it is still headphone jack with pin-ctl : 0xc0 OUT HP while mic jack and line in jack 's pin ctl are changed to 0x40 OUT

channel mode only change two mio jacks from IN to OUT

May need to use add_out_jack_mode=1 instead of add_jack_modes=1 when there are Mic and line in jacks

Use Headphone Jack Mode control to switch HP to Line Out for pin-ctl and EAPD

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/?id=f811c3cf8fae63ecc8a937ba7376490e2565f8f1

Quoted 1 line

To exclude that my speakers are broken or wrong connected: I get sound

from

Quoted 1 line

front left and front right if i switch in KDE configuration module to

"Analog

Quoted 1 line

duplex stereo", but then I get no sound from rest of my speakers.

http://cgit.freedesktop.org/pulseaudio/pulseaudio/tree/src/modules/alsa/mixer/paths/analog-output-headphones.conf

pulseaudio mute external center/lfe controls when headphone jack is plugged since pulseaudio not aware that the role of headphone has been changed

[Element Center]
switch = off
volume = off

[Element LFE]
switch = off
volume = off

Quoted 3 lines

KDE configuration module lets me choose "connector" configuration but

only in

Quoted 5 lines

stereo mode.
In stereo mode I can choose between "headphones" and "speakers". If it is set to "headphones" I hear sound in front left and front right speakers.
If it is set to "speakers" I hear sound in rear left and rear right

speakers.

Quoted 1 line

you need to switch "channel mode" to "2 ch" if you want to use your 5.1 internal speaker

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/?id=786c51f9168cfd2d49250c6e5e60035cbb2fd5a1

There are difference between static model and generic parser

_______________________________________________
pulseaudio-discuss mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/pulseaudio-discuss

#8 lore raw
In reply to a message not in the archive
Quoted 2 lines
Quoted 2 lines

seem internal subwoofer only use one channel and don't have any stereo

to

Quoted 8 lines
Quoted 6 lines

mono downmix according to your patch

It is not easy to assign different name to internal 4.1 and external 5.1 speaker when alc888 only has five DAC

Some playback volume control must be shared

If you know what's missing, you could send a few lines of code and I will

test

Quoted 1 line

it, otherwise I'll have to experiment on my own.

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/patch/sound/pci/hda/patch_realtek.c?id=
c3e837bbcc03e39991da5dd1f791c0 6cde9f7a45

As your patch indicate internal subwoofer use external center speaker channel and your codec does not support L/R swap

You may need to reserve Audio mixer 0x26 for internal subwoofer playback volume by restrict the connection of the internal rear speaker

excluding 0x26 so that last DAC can be assigned to the internal subwoofer similar to alc889_fixup_dac_route

void alc888_fixup_dac_route(struct hda_codec *codec,
const struct alc_fixup *fix, int action)
{
if (action == ALC_FIXUP_ACT_PRE_PROBE) {

hda_nid_t conn1[4] = { 0x0c, 0x0d, 0x0e, 0x0f};

snd_hda_override_conn_list(codec, 0x17, 4, conn1);

} else if (action == ALC_FIXUP_ACT_PROBE) {
conn[5] = { 0x0c, 0x0d, 0x0e, 0x0f, 0x26 };
snd_hda_override_conn_list(codec, 0x17, 5, conn);

}
}

Quoted 1 line

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/patch/sound/pci/hda/patch_realtek.c?id=
c3e837bbcc03e39991da5dd1f791c0 6cde9f7a45

Quoted 9 lines
Quoted 2 lines

Do you mean internal subwoofer has low pass filter

I don't know. How to check it?

Quoted 1 line

what do you mean when you say 4.1 worked fine ?

External 5.1 speakers working as 4.1 speakers because such profile was

set.

Quoted 7 lines
Quoted 4 lines

The channel map of internal 4.1 speaker are different from external 5.1 speaker

Recently I also made such conclusion.

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/?id=2d3391ec0ecca37efb6bc995906292f47522b471

Seem 4.1 is not defined in snd_pcm_std_chmap and you need to define and add your 4.1 chmap similar to 2.1

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/?id=ee81abb623cb5e03c182d16871bb4fb34fdc9b4f

#17 lore raw
In reply to a message not in the archive
Quoted 8 lines
Quoted 8 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

My problem is that when I set channel output to "Analog output

surround

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

5.1"
(or 2.1 or 4.1), I hear no sound in front speakers, but in case of

Quoted 7 lines
Quoted 7 lines

5.1 or

Quoted 1 line
Quoted 1 line
Quoted 1 line

4.1

You need pulseaudio lfe-filter for 2.1

http://cgit.freedesktop.org/pulseaudio/pulseaudio/log/?qt=grep&q=lfe-filter

Quoted 2 lines

External 5.1 and 4.1 worked fine without lfe-filter. Fedora doesn't

package lfe-

Quoted 3 lines

filter and I'm more interested to get my 5.1 configuration back.

Quoted 1 line

do you mean surround21 need 6 channel instead of channels with 5.1

internal

Quoted 3 lines
Quoted 3 lines

/external speaker ?

http://git.alsa-project.org/?p=alsa-lib.git;a=commitdiff;h=48f1b308cc66152eb

Quoted 3 lines
Quoted 1 line

6db66742dd0d08d888cda8d;hp=5c4cd46810cef8850b037fca9e38ffd43b0bff22

No. When in KDE channel output is set to 2.1 it makes no difference what

is set

Quoted 1 line

in alsamixer. When my external speakers are disconnected built-in front

left

Quoted 1 line

and front right works on my laptop, but built-in subwoofer doesn't work

There

Quoted 6 lines

is no difference what channel output is set in alsamixer.

My laptop has built-in front left, front right, rear left, rear right and subwoofer and something is strange.
When I set channel output to 5.1 or 4.1 and external speakers are disconnected, then front left and front right work as expected but

built-in

Quoted 1 line

subwoofer is heard only if I test rear left channel (wrong channel

mapping?)

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda/hda_codec.c?id=cd4035e814b04c009ece9939396d06370c53ed44

Seem only two pairs of stereo speakers and internal subwoofer at left channel before this patch

ALSA: hda - Enable surround speakers (when line out is also present)

#19 lore raw
In reply to a message not in the archive
Quoted 1 line
Quoted 1 line
Quoted 1 line

My laptop has built-in front left, front right, rear left, rear right

and

Quoted 11 lines
Quoted 11 lines
Quoted 3 lines

subwoofer and something is strange.
When I set channel output to 5.1 or 4.1 and external speakers are disconnected, then front left and front right work as expected but

built-in

Quoted 1 line

subwoofer is heard only if I test rear left channel (wrong channel

mapping?)

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pc

Quoted 8 lines
Quoted 6 lines

i/hda/hda_codec.c?id=cd4035e814b04c009ece9939396d06370c53ed44

Seem only two pairs of stereo speakers and internal subwoofer at left channel before this patch

ALSA: hda - Enable surround speakers (when line out is also present)

On my laptop case "Virtual SurroundSound" is written . When I test front

left

Quoted 1 line

and rear left, I hear distinct sound, so it would mean it's from two

different

Quoted 1 line

sources of sound.

The driver use more than two channels only after David 's patch

But all internal speakers of the notebook are at front of the user, The 3D sound effect is quite different from your external 5.1 speakers

Do you mean your 5930g need champ {FL FR RL RR LFE }?

This can be easily implemented by using "swap center/lfe" switch for those codec support R/L swap

http://git.alsa-project.org/?p=alsa-lib.git;a=blob_plain;f=test/chmap.c;hb=HEAD

http://git.alsa-project.org/?p=alsa-lib.git;a=tree;f=src/conf/pcm;hb=HEAD

If codec does not support R/L swap, your 4.1 swap chmap need 5.0 routing

Do you expect pulseaudio show 4.1 swap(5.0) profile for internal speakers and 4.1 and 5.1 profiles for external speakers ?

_______________________________________________
pulseaudio-discuss mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/pulseaudio-discuss

#16 lore raw
In reply to a message not in the archive
Quoted 11 lines
Quoted 2 lines

http://cgit.freedesktop.org/pulseaudio/pulseaudio/tree/src/modules/alsa/mixe

Quoted 5 lines
Quoted 3 lines
Quoted 3 lines

r/paths/analog-output-headphones.conf

pulseaudio mute external center/lfe controls when headphone jack is

plugged

That would be unwanted.

This is common to all notebook using headphone jack and two other jacks to support surround51 or surround71 since pulseaudio mute the other retasked mio jack when headphone jack is plugged

Quoted 4 lines
Quoted 3 lines
Quoted 3 lines

I used hdajackretask to override:
PIN ID: 0x15 to "Line out (front)"

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/patch/sound/pci/hda/patch_realtek.c?id=c3e837bbcc03e39991da5dd1f791c06cde9f7a45

When the static model were used, the jack was configured as line out instead of headphone jack and there is no headphone playback volume

-static const struct hda_verb alc888_acer_aspire_4930g_verbs[] = { -/* Enable unsolicited event for HP jack */
- {0x15, AC_VERB_SET_UNSOLICITED_ENABLE, ALC_HP_EVENT | AC_USRSP_EN},
-/* Connect HP out to front */

-    {0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
-    {0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
-    {0x15, AC_VERB_SET_CONNECT_SEL, 0x00},
-    {0x15, AC_VERB_SET_EAPD_BTLENABLE, 2},

-static const struct snd_kcontrol_new alc888_acer_aspire_4930g_mixer[] = {
- HDA_CODEC_VOLUME("Front Playback Volume", 0x0c, 0x0, HDA_OUTPUT),
- HDA_BIND_MUTE("Front Playback Switch", 0x0c, 2, HDA_INPUT),

The jack is configured as headphone jack after the auto parser is used

Quoted 9 lines
Quoted 1 line

Pulseaudio don't know node 0x15 is headphone / Line Out (External

speaker)

Quoted 2 lines

select speaker profile mute the headphone playback switch

Doesn't HP mean HeadPhone? Isn't solution to my problem obvious, namely add Line out capability to 0x15?

Are there any side effect if you change the headphone jack to Line Out jack as the jack no longer enable HP amp ?

use add_out_jack_modes for create Headphone/Line Out jack mode control to change Headphone to Line Out and vice versa

sound/pci/hda/hda_generic.c +1 -1
index 3d2597b..f25cd23 100644
@@ -180,10 +180,10 @@ static void parse_user_hints(struct hda_codec *codec)
     /* the following two are just for compatibility */
     val = snd_hda_get_bool_hint(codec, "add_out_jack_modes");
     if (val >= 0)
-        spec->add_jack_modes = !!val;
+        spec->add_out_jack_modes = !!val;
     val = snd_hda_get_bool_hint(codec, "add_in_jack_modes");
     if (val >= 0)
        spec->add_jack_modes = !!val;
@@ -2640,7 +2642,7 @@ static void get_jack_mode_name(struct hda_codec

*codec, hda_nid_t pin,
static int get_out_jack_num_items(struct hda_codec *codec, hda_nid_t pin)

 {
     struct hda_gen_spec *spec = codec->spec;
-    if (spec->add_jack_modes) {
+    if (spec->add_out_jack_modes || spec->add_jack_modes) {
         unsigned int pincap = snd_hda_query_pin_caps(codec, pin);
         if ((pincap & AC_PINCAP_OUT) && (pincap & AC_PINCAP_HP_DRV))
             return 2;
@@ -4892,7 +4895,7 @@ int snd_hda_gen_parse_auto_config(struct hda_codec
*codec,
             return err;
     }

- if (spec->add_jack_modes) {

+    if (spec->add_out_jack_modes || spec->add_jack_modes) {
         if (cfg->line_out_type != AUTO_PIN_SPEAKER_OUT) {
             err = create_out_jack_modes(codec, cfg->line_outs,
                             cfg->line_out_pins);
sound/pci/hda/hda_generic.h +1 -0
index 56e4139..8d7568b 100644
@@ -227,6 +227,8 @@ struct hda_gen_spec {
     unsigned int prefer_hp_amp:1; /* enable HP amp for speaker if any */
     unsigned int add_stereo_mix_input:2; /* add aamix as a capture src */
     unsigned int add_jack_modes:1; /* add i/o jack mode enum ctls */
+    unsigned int add_out_jack_modes:1;
     unsigned int power_down_unused:1; /* power down unused widgets */
     unsigned int dac_min_mute:1; /* minimal = mute for DACs */

_______________________________________________
pulseaudio-discuss mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/pulseaudio-discuss

#10 lore raw
In reply to a message not in the archive
Quoted 1 line

I started MS Windows and without externals speakers plugged in I could

test

Quoted 1 line

5.1 configuration and it seemed that sound was coming from different

directions.

Quoted 7 lines

What I managed to determine:
I've got 3 stacks:
1 ST: Headphone, Line-out (FL and FR), SPDIF
2 ST: Microphone, Line-out (CLFE)
3 ST: Line-in, Line-out (RL and RR)

Quoted 8 lines

I've got 5 responsive output pins
PIN 0x14: Internal FL FR
PIN 0x15: External FL FR
PIN 0x17: Internal LFE
PIN 0x18: External CLFE
PIN 0x1a: External RL RR

How can we make it work with these information?

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/plain/Documentation/sound/alsa/Channel-Mapping-API.txt

seem chnmap type _FIXED , _VAR and _PAIRED does not fit when LFE and FC can be swapped for internal speaker and external speaker

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda?id=0fb87bb474f978446786263deff6263284e6e011

How do the driver implement channel map when codec has swap center/lfe switch ?

Do chnmap contain both {FL FR RL RR FC LFE} and {FL FR RL RR LFE FC} ?

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda?id=5a61358433b1f89b500f2c365746c73cb7a27e2f

atihdmi_paired_swap_fc_lfe

#13 lore raw
In reply to a message not in the archive
Quoted 10 lines

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/patch/sound/pci

Quoted 4 lines

/hda/patch_realtek.c?id=c3e837bbcc03e39991da5dd1f791c06cde9f7a45

When the static model were used, the jack was configured as line out instead of headphone jack and there is no headphone playback volume

That's rather "relevant change". Good job in finding it. I would like such configuration (or better) back.

I don't see any side effect neither with your changes to hda_generic nor

Quoted 3 lines

with
vanilla kernel, but I don't know what problems should I expect.

Do headphone get same volume level when the jack is configured as Line Out (without enable Headphone Amplifier) ?

The driver use different automute method when the jack is configured as HP and Line Out

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda?id=e0d32e335fc0e354db93a807736243f5035fbc67

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda?id=a365fed9806e182cb4e1b7bb1855759489d95858
http://cgit.freedesktop.org/pulseaudio/pulseaudio/tree/src/modules/alsa/mixer/paths

if you look at speaker.conf , lineout.conf and headphone.conf, it seem pulseaudio is unlikely mute all internal speakers when one pair of the playback volume control need to be shared by internal speaker and external speakers

you need dirver 's automute instead of pulseaudio 's automute

==> Best config: lo_type=2, wired=1, mio=1
multi_outs = 15/0/0/0 : 2/3/4/0 (type HP)
out path: depth=3 '02:0c:15'
multi_ios(2) = 1a/18 : 3/4
mio path: depth=3 '03:0d:1a'
mio path: depth=3 '04:0e:18'
spk_outs = 14/17/16/0 : 5/25/4/0
spk path: depth=3 '05:0f:14'
spk path: depth=3 '25:26:17'
spk path: depth=3 '04:0e:16'

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda/hda_generic.c?id=e80c60f3cbe76fa95029abc53b1a29172b51b96a

when line out type == AUTO_PIN_HP_OUT

should first do_mute() use speaker_path instead of out_path
<https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda/hda_generic.c?id=7385df6134888553b5ede71cd573ffe0429e2a80>

Quoted 13 lines
Quoted 13 lines
Quoted 1 line

I started MS Windows and without externals speakers plugged in I

could test

Quoted 1 line

5.1 configuration and it seemed that sound was coming from

different directions.

Quoted 7 lines

What I managed to determine:
I've got 3 stacks:
1 ST: Headphone, Line-out (FL and FR), SPDIF
2 ST: Microphone, Line-out (CLFE)
3 ST: Line-in, Line-out (RL and RR)

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

I've got 5 responsive output pins
PIN 0x14: Internal FL FR
PIN 0x15: External FL FR
PIN 0x17: Internal LFE
PIN 0x18: External CLFE
PIN 0x1a: External RL RR

How can we make it work with these information?

speaker-test -Dhw:0,0 -c6 -t wav

Quoted 3 lines
Quoted 3 lines

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/plain/Documentation/sound/alsa/Channel-Mapping-API.txt

Quoted 7 lines
Quoted 4 lines

[1]

seem chnmap type _FIXED , _VAR and _PAIRED does not fit when LFE and FC can be swapped for internal speaker and external speaker

Right, you can't do it with a single map of one of those types.

http://git.alsa-project.org/?p=alsa-utils.git&a=search&h=HEAD&st=commit&s=chmap

do chmap of internal speakers need {FL FR RL RR LFE NA} ?

http://git.alsa-project.org/?p=alsa-lib.git&a=search&h=HEAD&st=commit&s=chmap

as set_chmap() still not yet implemented in pcm_route.c

do speaker-test need to specify channel map when using those odd number channels ?

speaker-test -D surround21  -c3 -t wav
speaker-test -D surround41  -c5 -t wav -mFL,FR,RL,RR,LFE
speaker-test -D surround50  -c5 -t wav

http://git.alsa-project.org/?p=alsa-utils.git;a=commitdiff;h=7b14c00b56784f69ecc954a2de36e0a058fc8849;hp=000bf230cfb3b0abe88d27701dd77982675126ec

this example seem not working

speaker-test -c2 -t wav -Dplug:front -mFR,FL

Quoted 3 lines
Quoted 3 lines

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda?id=0fb87bb474f978446786263deff6263284e6e011

Quoted 9 lines
Quoted 6 lines

[2]

How do the driver implement channel map when codec has swap center/lfe switch ?

Do chmap contain both {FL FR RL RR FC LFE} and {FL FR RL RR LFE FC} ?

If you want to provide support for userspace doing it both ways, then

yes, you need those two _FIXED maps.

Can chmap contain two _FIXED maps of same number of channels ?

#14 lore raw

14.05.2015, 09:26, Raymond Yau kirjoitti:

Quoted 34 lines
Quoted 13 lines
Quoted 13 lines
Quoted 1 line

I started MS Windows and without externals speakers plugged in I

could test

Quoted 1 line

5.1 configuration and it seemed that sound was coming from

different directions.

Quoted 7 lines

What I managed to determine:
I've got 3 stacks:
1 ST: Headphone, Line-out (FL and FR), SPDIF
2 ST: Microphone, Line-out (CLFE)
3 ST: Line-in, Line-out (RL and RR)

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

I've got 5 responsive output pins
PIN 0x14: Internal FL FR
PIN 0x15: External FL FR
PIN 0x17: Internal LFE
PIN 0x18: External CLFE
PIN 0x1a: External RL RR

How can we make it work with these information?

speaker-test -Dhw:0,0 -c6 -t wav

Quoted 3 lines
Quoted 3 lines

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/plain/Documentation/sound/alsa/Channel-Mapping-API.txt

Quoted 6 lines
Quoted 4 lines

[1]

seem chnmap type _FIXED , _VAR and _PAIRED does not fit when LFE and FC can be swapped for internal speaker and external speaker

Quoted 7 lines
Quoted 1 line

Right, you can't do it with a single map of one of those types.

http://git.alsa-project.org/?p=alsa-utils.git&a=search&h=HEAD&st=commit&s=chmap

do chmap of internal speakers need {FL FR RL RR LFE NA} ?

From above it looks like there are 3 internal speakers, so I guess e.g.

{FL FR LFE NA} might be in order (or just {FL FR LFE} if 3-channel playback is supported).

Quoted 10 lines

http://git.alsa-project.org/?p=alsa-lib.git&a=search&h=HEAD&st=commit&s=chmap

as set_chmap() still not yet implemented in pcm_route.c

do speaker-test need to specify channel map when using those odd number channels ?

speaker-test -D surround21  -c3 -t wav
speaker-test -D surround41  -c5 -t wav -mFL,FR,RL,RR,LFE
speaker-test -D surround50  -c5 -t wav

Well, the driver should provide the correct chmap.

Quoted 5 lines

http://git.alsa-project.org/?p=alsa-utils.git;a=commitdiff;h=7b14c00b56784f69ecc954a2de36e0a058fc8849;hp=000bf230cfb3b0abe88d27701dd77982675126ec

this example seem not working

speaker-test -c2 -t wav -Dplug:front -mFR,FL

You are getting an error?
If so, that is expected if the underlying device does not support the wanted channel map.

Quoted 9 lines
Quoted 3 lines
Quoted 3 lines

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda?id=0fb87bb474f978446786263deff6263284e6e011

Quoted 5 lines
Quoted 5 lines

[2]

How do the driver implement channel map when codec has swap center/lfe switch ?

Quoted 7 lines
Quoted 4 lines
Quoted 1 line

Do chmap contain both {FL FR RL RR FC LFE} and {FL FR RL RR LFE FC} ?

If you want to provide support for userspace doing it both ways, then

yes, you need those two _FIXED maps.

Can chmap contain two _FIXED maps of same number of channels ?

Sure.

Signature · 1 line
Anssi Hannula
#15 lore raw
Quoted 13 lines
Quoted 13 lines
Quoted 13 lines
Quoted 13 lines
Quoted 1 line

I started MS Windows and without externals speakers plugged in I

could test

Quoted 1 line

5.1 configuration and it seemed that sound was coming from

different directions.

Quoted 7 lines

What I managed to determine:
I've got 3 stacks:
1 ST: Headphone, Line-out (FL and FR), SPDIF
2 ST: Microphone, Line-out (CLFE)
3 ST: Line-in, Line-out (RL and RR)

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

I've got 5 responsive output pins
PIN 0x14: Internal FL FR
PIN 0x15: External FL FR
PIN 0x17: Internal LFE
PIN 0x18: External CLFE
PIN 0x1a: External RL RR

How can we make it work with these information?

speaker-test -Dhw:0,0 -c4 -t wav

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda/patch_realtek.c?id=7cef4cf1c5e9d81554137f52b96a5ab7f6241cdd

You need to notify user of other acer aspire which use quirk ALC888_ACER_ASPIRE_4930G if you want to remove node 0x16

Quoted 3 lines
Quoted 3 lines
Quoted 2 lines
Quoted 2 lines

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/plain/Documentation/sound/alsa/Channel-Mapping-API.txt

Quoted 9 lines
Quoted 9 lines
Quoted 7 lines
Quoted 4 lines

[1]

seem chnmap type _FIXED , _VAR and _PAIRED does not fit when LFE and FC can be swapped for internal speaker and external speaker

Right, you can't do it with a single map of one of those types.

http://git.alsa-project.org/?p=alsa-utils.git&a=search&h=HEAD&st=commit&s=chmap

Quoted 6 lines
Quoted 2 lines

do chmap of internal speakers need {FL FR RL RR LFE NA} ?

From above it looks like there are 3 internal speakers, so I guess e.g. {FL FR LFE NA} might be in order (or just {FL FR LFE} if 3-channel playback is supported).

This is different from 2.1 internal speakers when yours also support external 5.1

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda?id=f37bc7a88d374448a1f4bba9267d308606d78bf2

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda?id=8e38395360844806041ea69ab9690f5f174bc40c

Quoted 2 lines
Quoted 2 lines

http://git.alsa-project.org/?p=alsa-utils.git;a=commitdiff;h=7b14c00b56784f69ecc954a2de36e0a058fc8849;hp=000bf230cfb3b0abe88d27701dd77982675126ec

Quoted 6 lines
Quoted 4 lines

this example seem not working

speaker-test -c2 -t wav -Dplug:front -mFR,FL

You are getting an error?

Unable to set channel map

Quoted 3 lines

If so, that is expected if the underlying device does not support the wanted channel map.

Seem only those idt codecs which wcaps support R/L swap but hda-intel use snd_pcm_std_chmap

Are there any other sound card support swap front right and front left ?

#20 lore raw
In reply to Łukasz Wojniłowicz
Quoted 2 lines

My problem is that when I set channel output to "Analog output surround

5.1"

Quoted 1 line

(or 2.1 or 4.1), I hear no sound in front speakers, but in case of 5.1 or

4.1

Quoted 1 line

I can hear sound in rear speakers. I use kernel 3.19.5 and it didn't

happen in

Quoted 9 lines

earlier kernels that is 3.18 and in 3.17 for sure.

My configuration is:
OS: Fedora 21 64 bit
SoundCard: ALC888
Model name: acer-aspire-4930g
Laptop: Acer Aspire 5930g
Speakers: external 5.1 with 3 jacks
Sound channel configuration module is standard configuration module from

KDE.

Quoted 6 lines

Additional info:
1) When channel output is 5.1 and I unplug green jack and leave two others jacks connected then I can hear sound in laptop internal speakers.
2) Earlier (kernel 3.18 and 3.17) I didn't have possibility to choose 2.1 configuration and additionally to 4.1 configuration I could also choose

4.0

Quoted 1 line

configuration.

You have to provide pulseaudio verbose log

If driver create channel mode which allow you to support surround5.1 with your headphone, line in and mic jack

It is possible for pulseaudio mute two of your external 5.1 speaker when headphone jack is plugged

http://cgit.freedesktop.org/pulseaudio/pulseaudio/tree/src/modules/alsa/mixer/paths/analog-output-headphones.conf

[Element Rear]
switch = off
volume = off

[Element Surround]
switch = off
volume = off

[Element Center]
switch = off
volume = off

[Element LFE]
switch = off
volume = off

_______________________________________________
pulseaudio-discuss mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/pulseaudio-discuss

#24 lore raw
In reply to a message not in the archive
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

No change.

http://www.alsa-project.org/db/?f=30b3f0087374b914a20dbe20a618fb892a5d6fd5

Quoted 4 lines
Quoted 4 lines

Are there any offical specificaion ?

So far most review only mention stereo speakers and subwoofer, the

service

Quoted 4 lines
Quoted 1 line

guide only show how to replace two internal speakers

Service manual mentions
"Dolby®-certified surround sound system with two built-in stereo

speakers and

Quoted 6 lines

one subwoofer supporting low-frequency effects"

so all additional channels what I'm hearing in Windows is emulated. I hope that it is clear now that my laptop has two internal speakers and one subwoofer.

You have to determine which node 0x16 or 0x17 is your subwoofer and remove the redundant speaker pin fixup

Quoted 1 line

Thanks. I know how to help myself, but I expected it by default. I wonder

how > many other users will manage to get their sound working good as before > regression. > And wasn't "model=acer-aspire-4930g" some sort of early patching which was > thrown out of official code?

After remove the redundant internal speaker, 5.1 is only available after you change the channel mode

Can alsactl restore the channel mode before pulseaudio probe the sound cards ?

Auto mic select is not enabled when the notebook has mic jack and line in jack , internl mic

As jack retasking is specific to snd-hda-intel and some multi cjannel ac97 codecs

It is not easy to force pulseaudio to stop all client connection, reprobe the profiles on board audio after jack retasking

hdajackretask also perform the same function
stop pulseaudio and using dynamic reconfiguration/early patching

For those notebook with headphone spdif combo jack, it need a customised iec958.conf and you can use headphone jack to make iec958 unavailable

http://cgit.freedesktop.org/pulseaudio/pulseaudio/tree/src/modules/alsa/mixer/paths/iec958-stereo-output.conf

[Jack Headphone]
state.plugged = no
state.unplugged = unknown

_______________________________________________
pulseaudio-discuss mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/pulseaudio-discuss

#27 lore raw
In reply to a message not in the archive
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

No change.

http://www.alsa-project.org/db/?f=30b3f0087374b914a20dbe20a618fb892a5d6fd5

Quoted 4 lines
Quoted 4 lines

Are there any offical specificaion ?

So far most review only mention stereo speakers and subwoofer, the

service

Quoted 4 lines
Quoted 1 line

guide only show how to replace two internal speakers

Service manual mentions
"Dolby®-certified surround sound system with two built-in stereo

speakers and

Quoted 7 lines

one subwoofer supporting low-frequency effects"

so all additional channels what I'm hearing in Windows is emulated. I hope that it is clear now that my laptop has two internal speakers and one subwoofer.

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda?id=8e38395360844806041ea69ab9690f5f174bc40c

You need to define your 2.1 chmap if the subwoofer only use left channel

Compiling and running PulseAudio from git

http://colin.guthr.ie/2010/09/compiling-and-running-pulseaudio-from-git/
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

#29 lore raw
In reply to a message not in the archive
Quoted 2 lines
Quoted 2 lines

http://www.alsa-project.org/db/?f=30b3f0087374b914a20dbe20a618fb892a5d6fd5

Quoted 11 lines
Quoted 11 lines
Quoted 4 lines
Quoted 4 lines

Are there any offical specificaion ?

So far most review only mention stereo speakers and subwoofer, the

service

Quoted 4 lines
Quoted 1 line

guide only show how to replace two internal speakers

Service manual mentions

Quoted 7 lines
Quoted 7 lines
Quoted 1 line

"Dolby®-certified surround sound system with two built-in stereo

speakers and

Quoted 3 lines

one subwoofer supporting low-frequency effects"

so all additional channels what I'm hearing in Windows is emulated. I

hope

Quoted 4 lines
Quoted 4 lines
Quoted 2 lines

that it is clear now that my laptop has two internal speakers and one subwoofer.

https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pc

Quoted 9 lines
Quoted 7 lines

i/hda?id=8e38395360844806041ea69ab9690f5f174bc40c

You need to define your 2.1 chmap if the subwoofer only use left channel

Compiling and running PulseAudio from git

http://colin.guthr.ie/2010/09/compiling-and-running-pulseaudio-from-git/

In Fedora 22 workaround with setting "Line out (front)" for 0x15 pin

doesn't

Quoted 3 lines

work.

Sound on my system is totally fucked up.

http://cgit.freedesktop.org/pulseaudio/pulseaudio/tree/src/modules/alsa/mixer/paths/analog-output-lineout.conf

Are you sure that it is alsa driver bug since pulseaudio seem not using line out jack to mute internal speakers ?

by adding new hint alt_config , you can use alt_config to select different set of pin config

(quoted diff) +0 -0

b/sound/pci/hda/hda_auto_parser.c
index 03b7399..683a0ab 100644

sound/pci/hda/hda_auto_parser.c +4 -0
@@ -952,6 +952,7 @@ void snd_hda_pick_fixup(struct hda_codec *codec,
     const struct snd_pci_quirk *q;
     int id = HDA_FIXUP_ID_NOT_SET;
     const char *name = NULL;
+    int i;
 
     if (codec->fixup_id != HDA_FIXUP_ID_NOT_SET)
         return;
@@ -966,6 +967,9 @@ void snd_hda_pick_fixup(struct hda_codec *codec,
         return;
     }
 
+    if (!snd_hda_get_int_hint(codec, "alt_config", &i))
+        codec->alt_config = i;
+
     if (codec->modelname && models) {
         while (models->name) {
             if (!strcmp(codec->modelname, models->name)) {
sound/pci/hda/patch_realtek.c +0 -0
index 8e02cdf..f406835 100644
@@ -1914,6 +1914,31 @@ static void alc889_fixup_mba21_vref(struct hda_codec

*codec,

         alc889_fixup_mac_pins(codec, nids, ARRAY_SIZE(nids));

}

+static void alc888_fixup_acer_aspire_4930g(struct hda_codec *codec,
+ const struct hda_fixup *fix, int action)
+{
+ struct hda_pintbl subwoofer_config[] = {
+ { 0x16, 0x90170111 }, /* internal subwoofer */
+ {}
+ };
+ struct hda_pintbl alt_config[] = {

+        { 0x15, 0x02014010},
+        { 0x1a, 0x02014011},
+        { 0x18, 0x02014012},
+        {}
+    };
+    snd_hda_apply_pincfgs(codec, subwoofer_config);
+    switch(codec->alt_config){
+    case 1:
+        codec_info(codec, "5.1 External Speaker\n");
+        snd_hda_apply_pincfgs(codec, alt_config);
+        break;

+ default:
+ codec_info(codec, "use [Hint]\nalt_config=1 for 5.1 External
Speaker\n");
+ break;
+ }
+}
+
/* Don't take HP output as primary
* Strangely, the speaker output doesn't work on Vaio Z and some Vaio
* all-in-one desktop PCs (for example VGC-LN51JGB) through DAC 0x05

@@ -2048,12 +2073,8 @@ static const struct hda_fixup alc882_fixups[] = {
         .v.func = alc889_fixup_coef,
     },
     [ALC882_FIXUP_ACER_ASPIRE_4930G] = {
-        .type = HDA_FIXUP_PINS,
-        .v.pins = (const struct hda_pintbl[]) {
-            { 0x16, 0x99130111 }, /* CLFE speaker */
-            { 0x17, 0x99130112 }, /* surround speaker */
-            { }
-        },
+        .type = HDA_FIXUP_FUNC,
+        .v.func = alc888_fixup_acer_aspire_4930g,
         .chained = true,
         .chain_id = ALC882_FIXUP_GPIO1,
     },

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel