Skip to contentSkip to conversation

P4080 Reset Vector

U-Boot MArunKumar 5 participants 14 messages Sep 8, 2010 – Sep 27, 2010

lore
Share & tools
lore

MArunKumar

author
#0 lore raw

Hi
Im new to u-boot. Right now im in the process of customizing P4080DS(RDB) to my board.
My doubt is, for P4080 the reset vec address is 0x0_ffff_fffc.
1) But in the config.mk file it is mentioned as 0xefff_fffc wat it mean?.

Regards
M.Arunkumar

Signature · 2 lines
View this message in context: http://old.nabble.com/P4080-Reset-Vector-tp29641685p29641685.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#1 lore raw
Quoted 6 lines · MArunKumar

Hi
Im new to u-boot. Right now im in the process of customizing P4080DS(RDB) to my board.
My doubt is, for P4080 the reset vec address is 0x0_ffff_fffc.
1) But in the config.mk file it is mentioned as 0xefff_fffc wat it mean?.

This is because the link address is 0xeff80000. We end up running at this address after the initial boot.

- k

#5 lore raw
Quoted 3 lines · Tony Wang

Hi All,

Could you tell me where can I download U-Boot for p4080, I have this board now.

What board? You can basic support for P4080 in the git tree for u-boot.

- k

#6 lore raw
Quoted 5 lines

What board? You can basic support for P4080 in the git tree for u-boot.

- k

Thanks Kumar,

Now I am use p4080ds board from freescale, I download U-Boot

2010.06 version.I check the board code for freescale, just

find p2020 directory, no p4080 board.

You said U-Boot has basic support for P4080, can you give

some more detail informaion such as file name or directory

name?

Best Regards,
/Tony

#7 lore raw
Quoted 5 lines

Now I am use p4080ds board from freescale, I download U-Boot

2010.06 version.I check the board code for freescale, just

Quoted 7 lines

find p2020 directory, no p4080 board.

You said U-Boot has basic support for P4080, can you give

some more detail informaion such as file name or directory

name?

If you can get the P4080DS board from Freecale,
Why did not you ask local Freescale sales to get the SDK software? There is all u-boot and kernel source code in the SDK software.

Thanks,
Dave

#3 lore raw
Quoted 11 lines · On Tue, 14 Sep 2010 01:43:40 -0700 MArunKumar <[email protected]> wrote:

Hi Kumar Gala

Thanks for ur kind reply.

Till, I am not clear why the resect vector points different address(0xefff_fffc).

From your reply, I understood Text_Base address is 0xeff8_0000, so the resetvec address points to 0xefff_fffc.

Quoted 6 lines

For all 85xx processor except(MPC8572) the resetvec = 0xffff_fffc, Text_Base = 0xfff8_0000
For p4080 the resetvec = 0xefff_fffc,Text_Base = 0xeff8_0000

For p4080 why the resetvec and Text_Base address is different from the other 85xx processor ?.

The reset vector is 0xfffffffc. 0xeffffffc is where the reset vector code sits once flash has been remapped. Until that remapping happens, you can't use any absolute addresses by symbol.

-Scott

#8 lore raw
In reply to Liu Dave-R63238

Thanks Dave and All,

For that reset address question, I think because p4080ds's FPGA can do this address decode and map 0xefffxxxx to 0xffffxxxx setting by SW7, is it right?

I also has another quesition, if I choose boot from bank0, why RCW should be programmed into address 0xe8000000? is it a rule of chip design?

Regards,
/Tony

#9 lore raw
Quoted 1 line

For that reset address question, I think because p4080ds's FPGA can do

this address

Quoted 1 line

decode and map 0xefffxxxx to 0xffffxxxx setting by SW7, is it right?

No. FPGA doesn't matter with it.

The e500mc core boot start address(0xFFFF_FFFC) will point to the end of CS0 Flash due to OR0[AM]=0.
In this phase, the core is using the relative addressing. After you change the BR0,OR0, you can use absolute addressing.

Keep in mind, the bootloader is placed to the end of CS0, and the RCW is placed to the start of CS0.

Quoted 1 line

I also has another quesition, if I choose boot from bank0, why RCW

should be

Quoted 1 line

programmed into address 0xe8000000? is it a rule of chip design?

#10 lore raw
Quoted 12 lines · Liu Dave-R63238 <r63238 <at> freescale.com> writes:
Quoted 2 lines

For that reset address question, I think because p4080ds's FPGA can do

this address

Quoted 1 line

decode and map 0xefffxxxx to 0xffffxxxx setting by SW7, is it right?

No. FPGA doesn't matter with it.

The e500mc core boot start address(0xFFFF_FFFC) will point to the end of CS0 Flash due to OR0[AM]=0.
In this phase, the core is using the relative addressing. After you change the BR0,OR0, you can use absolute addressing.

Quoted 7 lines

Keep in mind, the bootloader is placed to the end of CS0, and the RCW is placed to the start of CS0.

Quoted 1 line

I also has another quesition, if I choose boot from bank0, why RCW

should be

Quoted 1 line

programmed into address 0xe8000000? is it a rule of chip design?

Thanks Dave,

It look same as other PQ2/3 which using BR0/OR0 to set boot vecror base address.

just confirm, do you know CPU will read RCW data before it jump to 0xFFFF_FFFC?

/Tony

#11 lore raw
Quoted 1 line

It look same as other PQ2/3 which using BR0/OR0 to set boot vecror

base address.

Quoted 2 lines

just confirm, do you know CPU will read RCW data before it jump to

0xFFFF_FFFC?

Yes. CPU reset module must fetch RCW and configure CPU itself. then reset to 0xFFFF_FFFC, it is also same as PQ3.

Thanks,
Dave

author
#12 lore raw

hi
Kindly let me know how the branch instruction is loaded in reset vector address (0xffff_fffc), but i have mapped my boot flash from 0xE000_0000 to EFFF_FFFF in LAW.
please clarify me.

Quoted 19 lines · Liu Dave-R63238-2 wrote:
Quoted 2 lines

It look same as other PQ2/3 which using BR0/OR0 to set boot vecror

base address.

Quoted 2 lines

just confirm, do you know CPU will read RCW data before it jump to

0xFFFF_FFFC?

Yes. CPU reset module must fetch RCW and configure CPU itself. then reset to 0xFFFF_FFFC, it is also same as PQ3.

Thanks,
Dave

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Signature · 2 lines
View this message in context: http://old.nabble.com/P4080-Reset-Vector-tp29641685p29815731.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#13 lore raw
Quoted 5 lines · On Mon, 27 Sep 2010 01:43:53 -0700 MArunKumar <[email protected]> wrote:

hi
Kindly let me know how the branch instruction is loaded in reset vector address (0xffff_fffc), but i have mapped my boot flash from 0xE000_0000 to EFFF_FFFF in LAW.

When the chip starts execution, the boot vector is mapped at 0xfffffffc. The boot code then changes the flash mapping (with an interim state where it's mapped repeatedly throughout the address space) before it runs any code that depends on the link address.

-scott