Skip to contentSkip to conversation

BT test mode operation

Bluez-users Manjunath Prabhu 2 participants 4 messages Nov 24, 2004 Bluetooth drivers

lore
Share & tools
lore
#0 lore raw

hi marcel,
can i configure my bt dongles to operate in test mode....and then conduct the loopback or transmitter tests. This is indicated in the HCI part of the specification....so is it possible to run these tests just with BT devices connected to host PC's, and not using a BT protocol analyser.
If i buy a BT tester, then wouldn't my BT dongle be the DUT.... Also, if i buy a CATC-tracer/trainer, should I again buy a BT tester????

thanks and regards,
manjunath

-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now.
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

maintainer
#1 lore raw

Hi Manjunath,

Quoted 5 lines

can i configure my bt dongles to operate in test mode....and then conduct the loopback or transmitter tests. This is indicated in the HCI part of the specification....so is it possible to run these tests just with BT devices connected to host PC's, and not using a BT protocol analyser.

you can set your devices into test mode with the correct HCI command. I think you need to use "hcitool cmd ..." for that, because I never tried or implemented support for it.

What has this to do with a protocol analyzer?

Quoted 2 lines

If i buy a BT tester, then wouldn't my BT dongle be the DUT.... Also, if i buy a CATC-tracer/trainer, should I again buy a BT tester????

Actually what do you mean by BT Tester?

Regards

Marcel

-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now.
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

#2 lore raw

Hi Marcel,
1> So, i might have to generate hci cmds with correct opcodes for my BT dongles to communicate....I'll try and experiment a little bit. Has any work taken place on this front??

2> the BT tester i was talking about is more of a RF tester as given in this link http://www.elsinco.com/wi_blue.htm
So my question again is ...does a CATC trainer also accomodate the features of the product given in the above link.

thanks,
Best regards,
Manjunath

Quoted 23 lines · Marcel Holtmann

Hi Manjunath,

Quoted 5 lines

can i configure my bt dongles to operate in test mode....and then conduct the loopback or transmitter tests. This is indicated in the HCI part of the specification....so is it possible to run these tests just with BT devices connected to host PC's, and not using a BT protocol analyser.

you can set your devices into test mode with the correct HCI command. I think you need to use "hcitool cmd ..." for that, because I never tried or implemented support for it.

What has this to do with a protocol analyzer?

Quoted 2 lines

If i buy a BT tester, then wouldn't my BT dongle be the DUT.... Also, if i buy a CATC-tracer/trainer, should I again buy a BT tester????

Actually what do you mean by BT Tester?

Regards

Marcel

Quoted 10 lines

-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now.
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now.
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

maintainer
#3 lore raw

Hi Manjunath,

Quoted 3 lines

1> So, i might have to generate hci cmds with correct opcodes for my BT dongles to communicate....I'll try and experiment a little bit. Has any work taken place on this front??

actually using "hcitool cmd ..." is very easy.

Quoted 4 lines

2> the BT tester i was talking about is more of a RF tester as given in this link http://www.elsinco.com/wi_blue.htm
So my question again is ...does a CATC trainer also accomodate the features of the product given in the above link.

I don't think so, but how should I know. I am not a RF expert. May you should simply ask the CATC sales staff.

Regards

Marcel

-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now.
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users