same boot vmlinux trouble
Still having the same problem. Anyone have a more recent vmlinux kernel? Does anyone have a sample of what this boot output looks like when it works?
BTW I have mounted my linux dev directory on another linux machine and was able to write to the console device. Also was able to create new device files in the mounted directory and use those as well.
I'm pretty stuck here. Any help would be appreciated.
Regards,
Chad
Option? 5
Command Monitor. Type "exit" to return to the menu.
Quoted 1 line
Quoted 1 line
boot bootp()169.238.83.43:vmlinux nfsroot=169.238.83.43:/dist/linux/mipseb nfsaddrs=:169.238.83.43::0xffffff80:marvin2::
130768+22320+3184+341792+48560d+4604+6816 entry: 0x8bfa60d0 Obtaining vmlinux from server 169.238.83.43
PROMLIB: SGI ARCS firmware Version 1 Revision 10
PROMLIB: Total free ram 65814528 bytes (64272K,62MB)
ARCH: SGI-IP22
CPU: MIPS-R4400 FPU<MIPS-R4400FPC> ICACHE DCACHE SCACHE Loading R4000 MMU routines.
CPU revision is: 00000460
Primary instruction cache 16kb, linesize 16 bytes)
Primary data cache 16kb, linesize 16 bytes)
Secondary cache sized at 1024K linesize 128
Linux version 2.1.100 ([email protected]) (gcc version 2.7.2) #29 Thu Jul 9 22:19:39 EDT 1998
MC: SGI memory controller Revision 3
calculating r4koff... 000f43c2(1000386)
zs0: console input
zs0: console I/O
Calibrating delay loop... 99.94 BogoMIPS
Memory: 60364k/196116k available (1216k kernel code, 2684k data) Swansea University Computer Society NET3.039 for Linux 2.1
NET3: Unix domain sockets 0.16 for Linux NET3.038.
Swansea University Computer Society TCP/IP for NET3.037
IP Protocols: ICMP, UDP, TCP
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Starting kswapd v 1.5
Adv: about to run setup()
SGI Zilog8530 serial driver version 1.00
tty00 at 0xbfbd9838 (irq = 21) is a Zilog8530
tty01 at 0xbfbd9830 (irq = 21) is a Zilog8530
Ramdisk driver initialized : 16 ramdisks of 4096K size
loop: registered device at major 7
WD93: Driver version 1.25 compiled on Jul 7 1998 at 16:59:57
debug_flags=0x00
wd33c93-0: chip=WD33c93B/13 no_sync=0xff no_dma=0scsi0 : SGI WD93 scsi : 1 host.
sending SDTR 0103013f0csync_xfer=2c Vendor: IBM Model:
DCAS-32160 Rev: S65A
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 1, lun 0
sending SDTR 0103013f0csync_xfer=2c Vendor: SGI Model: SEAGATE
ST31200N Rev: 9278
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 3, lun 0
scsi : detected 2 SCSI disks total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 2077833 [1014 MB] [1.0 GB]sgiseeq.c: David S. Miller ([email protected])
eth0: SGI Seeq8003 08:00:69:07:9b:35
Sending BOOTP requests.... OK
IP-Config: Got BOOTP answer from 169.238.83.43, my address is 169.238.83.19
IP-Config: Gateway not on directly connected network. Partition check:
sda: sda1 sda2 sda3 sda4
sdb: sdb1 sdb2 sdb3 sdb4
Looking up port of RPC 100003/2 on 169.238.83.43
Looking up port of RPC 100005/1 on 169.238.83.43
VFS: Mounted root (nfs filesystem).
Adv: done running setup()
Freeing unused kernel memory: 44k freed
Warning: unable to open an initial console.
page fault from irq handler: 0000
$0 : 00000000 88180000 0000062d 00000000
$4 : 00000000 1004fc00 00000000 00000000
$8 : 00000000 00000000 00000000 abf33822
$12: 000a0000 8bf31070 8bf31000 00000000
$16: 8bf41000 8bf2c0e0 0000062d 881523c8
$20: abf41040 bfb94000 00000000 bfbd4000
$24: 00000000 8bf5fb58
$28: 88008000 88009dd8 0000000e 880e3f38
epc : 880e3e74
Status: 1004fc02
Cause : 00000008
Aiee, killing interrupt handler
Kernel panic: Attempted to kill the idle task!
In swapper task - not syncing
Quoted 9 lines · Chad Carlin
Still having the same problem. Anyone have a more recent vmlinux kernel? Does anyone have a sample of what this boot output looks like when it works?
BTW I have mounted my linux dev directory on another linux machine and was able to write to the console device. Also was able to create new device files in the mounted directory and use those as well.
I'm pretty stuck here. Any help would be appreciated.
This old kernel doesn't handle R4000 / R4400 SC versions correctly, you'll need a newer one.
Alex, could you brew a binary kernel from CVS? Thanks.
Ralf
Quoted 2 lines · On Tue, 12 Jan 1999 [email protected] wrote:
Alex, could you brew a binary kernel from CVS? Thanks.
I will as soon as linus.linux.sgi.com is alive again. Any news on this?
Incidentally, I've been working for the last few days on rewriting libfdisk. This is used inside the RH installer to mdoify and read partition tables. SGI tables are wildly different than anything else of course, and libfdisk is really only designed for pc/dos partition tables.
So, I'm rewriting it as nlibfdisk, and has support now for reading pc, sgi and macintosh partition tables. It's flexible enough to easily allow other partitioning formats.
Having this solved will let us have a better installer on the SGI, and also on Macintosh (both m68k and ppc).
When it's looking a little less stable, I'll ask people here to give it a shot on their partition tables (marked read only, of course).
- Alex