Skip to contentSkip to conversation

atyfb and 8500+ATI RagePro

DISCUSSION Hugh Caley 1 participant 1 message May 9, 1999

lore
Share & tools
lore

Hugh Caley

author
#0 lore raw

As an FYI, 29498928 does work with my PB G3 Series 300mhz; I can boot with video=atyfb:vmode:14,cmode:32,mclk:83.

Sometimes, though, the console speed is really slow, but if I boot and exit X, either Xpmac or XF68_FBDev, it becomes faster. Also, I am getting the little vertical snow band mentioned below when running X.

I'm using a 2.2.8 kernel I built from CVS source from openprojects yesterday.

Hugh

Quoted 3 lines · Timothy A. Seufert
Quoted 1 line · Geert Uytterhoeven

Hence the problem lies within the programming of the pixel and memory

clocks.

Quoted 2 lines

Could it be the same reference clock problem I was having? (I need to

sit

Quoted 3 lines

down and write some code to parameterize the reference clock.)

Mike, could you try the following change to atyfb.c? (without any

other

Quoted 3 lines

patches applied):

Find where ref_clk_per is defined. I don't have the source in front

of me

Quoted 7 lines

at the moment, but it will look something like:

unsigned long int ref_clk_per = 1000000000000UL/14318180;

This line sets atyfb's notion of the frequency of the card's reference

clock (from which all others are derived) to 14.318180 MHz. Please

try

Quoted 1 line

changing 14318180 to 29498928 and 28636360 to get 29.499 and 28.636

MHz

Quoted 3 lines

respectively.

I discovered that my Rage Pro card has a 29.498928 MHz reference

clock, and

Quoted 1 line

had some of the same symptoms as you (can't boot unless mclk is set

low).

Quoted 1 line

Once I set the reference clock to 29.499 MHz atyfb started working a

lot

Quoted 1 line

better (though I do get some snow in a thin vertical band near the

left

Quoted 1 line

side of the screen whenever video memory is being written).

I received similar advice from Geert yesterday. Indeed it helps with my

problem,
as I too have a card with a reference clock at 29.498 Mhz. I also get the same small
amount of snow down the penguin centerline during video activity.

Since the initial success, I have noticed that with actual use, I have various
problems (thin colored line at boot which goes away with the console, blanking and of the console display, etc.) so I think more remains to be

done.

I duplicated the DEBUG dump block so that I get a before and after picture of the
card setup on boot:

MacOS display is /bandit/ATY,XCLAIMVRPro
atyfb: 3D RAGE PRO (BGA, PCI) [0x4749 rev 0x7c] 12M SGRAM, 230 MHz PLL, 100 Mhz
MCLK
BUS_CNTL DAC_CNTL MEM_CNTL EXT_MEM_CNTL CRTC_GEN_CNTL DSP_CONFIG DSP_ON_OFF
7b33a040 87010182 00651a7b 75130c01 03000200 0038064a
0118061f
PLL ad d5 44 64 e4 13 80 91 8e 9e 29 01 a6 1b 00 00
BUS_CNTL DAC_CNTL MEM_CNTL EXT_MEM_CNTL CRTC_GEN_CNTL DSP_CONFIG DSP_ON_OFF
7b23a040 87010182 00751a7b 75130c01 03000200 003a0660
063500c0
PLL ad d5 41 14 dc 03 00 8a 8e 9e 29 01 a6 1b 00 00
Console: switching to colour frame buffer device 160x60
fb0: ATY Mach64 frame buffer device on /bandit/ATY,XCLAIMVRPro Monitor sense value = 0x73f, using video mode 6 and color mode 0.
fb1: control display adapter

mike.

--
"Brain-eating mutants are bad for business..." - Battle Angel Hugh "Batmensch" Caley

[[ This message was sent via the linuxppc-dev mailing list. Replies are ]] [[ not forced back to the list, so be sure to Cc linuxppc-dev if your ]] [[ reply is of general interest. Please check http://lists.linuxppc.org/ ]]
[[ and http://www.linuxppc.org/ for useful information before posting. ]]