Skip to contentSkip to conversation

USB Development

DISCUSSION michael cardenas 3 participants 3 messages May 11, 1999

lore
Share & tools
lore
#0 lore raw

I recently bought a 3 button unimouse to use in linux with my imac, but when I tried it out, I discovered that it uses the 1.16 spec and the usb patch in linuxppc4.1 only handles up to 1.0.

But, I am a programmer, and I'm very interested in helping develop linux.

My question is, where can I get the kernel source to get started and what compiler do I use? Is there a kernel build faq? I recently purchased the 4.1 cd, but I already had 4.1 installed.

I'd be willing to install pre r5 if I need to to work on the usb source.

Any pointers here will be greatly appreciated.

thanks,

Michael Cardenas
Software Engineer
Deneba Software

[[ This message was sent via the linuxppc-dev mailing list. Replies are ]] [[ not forced back to the list, so be sure to Cc linuxppc-dev if your ]] [[ reply is of general interest. Please check http://lists.linuxppc.org/ ]]
[[ and http://www.linuxppc.org/ for useful information before posting. ]]

#1 lore raw
Quoted 2 lines · michael cardenas

But, I am a programmer, and I'm very interested in helping develop linux.

yay. :)

Quoted 3 lines

My question is, where can I get the kernel source to get started and what compiler do I use? Is there a kernel build faq? I recently purchased the 4.1 cd, but I already had 4.1 installed.

Well. 4.1 ships w/ BootX (and a recent kernel then, yes? 2.1.125?). Goto
http://cvs.on.openprojects.net (I think that's it) and see howto checkout the kernel source there. It's the most current for ppc.

Quoted 1 line

I'd be willing to install pre r5 if I need to to work on the usb source.

Not needed.. R5 is nice tho <g>.

There are a few "problem" right now. The current USB dev is being done on Linus' USB stack. OHCI (what's in most non-intel chipset based computers) doesn't work. OHCI is the main controller. There is some hope tho. [email protected] is the current list.
http://soap.suitenine.com/usb/ has the current USB-ohci work and links to the other OHCI driver for Linus' stack (merging soon).

---
Tom Rini (TR1265)
http://dobbstown.yeti.edu/

[[ This message was sent via the linuxppc-dev mailing list. Replies are ]] [[ not forced back to the list, so be sure to Cc linuxppc-dev if your ]] [[ reply is of general interest. Please check http://lists.linuxppc.org/ ]]
[[ and http://www.linuxppc.org/ for useful information before posting. ]]

#2 lore raw
In reply to michael cardenas
Quoted 6 lines · michael cardenas

But, I am a programmer, and I'm very interested in helping develop linux.

My question is, where can I get the kernel source to get started and what compiler do I use? Is there a kernel build faq? I recently purchased the 4.1 cd, but I already had 4.1 installed.

Go to w3.one.net/~johnb for a lot of information on iMac linux. It
also has instructions for compiling a newer kernel with USB support, and the UUSBD has been updated several times since the 2.2.1 kernel that you are probably using. I think you can also find links to the development homepage for the UUSBD project. Finally, there is a new USB driver project for the kernel that will merge with the UUSBD code base in the future (at least, I'm betting on it). I'm running the 2.2.6 kernel on the iMac right now from the instructions on the iMac linux page.
Good luck!

--

+--------------------------------------+
Derek Moeller [email protected]
Linux for PowerPC User, Student
http://www.networksplus.net/moeller
"aut inveniam viam aut faciam"
+--------------------------------------+

[[ This message was sent via the linuxppc-dev mailing list. Replies are ]] [[ not forced back to the list, so be sure to Cc linuxppc-dev if your ]] [[ reply is of general interest. Please check http://lists.linuxppc.org/ ]]
[[ and http://www.linuxppc.org/ for useful information before posting. ]]