reproducible segfault in vgscan
Forwarded message form Paul Jakma <[email protected]>
-------- Original Message --------
Date: Wed, 3 May 2000 20:03:41 +0100 (IST)
From: Paul Jakma <[email protected]>
Subject: reproducible segfault in vgscan
Message-ID: <[email protected]>
MIME-Version: 1.0
i have a reproducible segfault with vgscan.
i had pvmove'd several lv's. Then i rebooted. since then, vgscan segfaults
the first 3 times out of every 4 times i run it.
eg:
[root@rossi linux]# vgscan
vgscan -- reading all physical volumes (this may take a while...) vgscan -- found active volume group "Main_VG" Segmentation fault
[root@rossi linux]# vgscan
vgscan -- reading all physical volumes (this may take a while...) vgscan -- found inactive volume group "Main_VG" Segmentation fault
[root@rossi linux]# vgscan
vgscan -- reading all physical volumes (this may take a while...) vgscan -- found inactive volume group "Main_VG" Segmentation fault
[root@rossi linux]# vgscan
vgscan -- reading all physical volumes (this may take a while...) vgscan -- found inactive volume group "Main_VG"
vgscan -- "/etc/lvmtab" and "/etc/lvmtab.d" successfully created vgscan -- WARNING: you may not have an actual VGDA backup of your volume
group
this means i have to call vgscan 4 times in a row from my initscripts before i can run vgchange.. :(
vgcfgrestore also has the same behaviour. :( segfault, segfault, segfault, ok, segfault, segfault segfault ok.. etc..
System is 2.3.99-pre6-pre7.
I've looked at the BUGS page but i don't see this problem listed.
Further info available on request..
regards,
Paul Jakma.
Could you provide your VG configuration ("vgdisplay -v") and a "vgscan -d" output to enable me to further dig into this one...
Thankd,
Heinz
Quoted 53 lines
Forwarded message form Paul Jakma <[email protected]>
-------- Original Message --------
Date: Wed, 3 May 2000 20:03:41 +0100 (IST)
From: Paul Jakma <[email protected]>
Subject: reproducible segfault in vgscan
Message-ID: <[email protected]>
MIME-Version: 1.0i have a reproducible segfault with vgscan.
i had pvmove'd several lv's. Then i rebooted. since then, vgscan segfaults
the first 3 times out of every 4 times i run it.eg:
[root@rossi linux]# vgscan
vgscan -- reading all physical volumes (this may take a while...) vgscan -- found active volume group "Main_VG" Segmentation fault
[root@rossi linux]# vgscan
vgscan -- reading all physical volumes (this may take a while...) vgscan -- found inactive volume group "Main_VG" Segmentation fault
[root@rossi linux]# vgscan
vgscan -- reading all physical volumes (this may take a while...) vgscan -- found inactive volume group "Main_VG" Segmentation fault
[root@rossi linux]# vgscan
vgscan -- reading all physical volumes (this may take a while...) vgscan -- found inactive volume group "Main_VG"
vgscan -- "/etc/lvmtab" and "/etc/lvmtab.d" successfully created vgscan -- WARNING: you may not have an actual VGDA backup of your volume
groupthis means i have to call vgscan 4 times in a row from my initscripts before i can run vgchange.. :(
vgcfgrestore also has the same behaviour. :( segfault, segfault, segfault, ok, segfault, segfault segfault ok.. etc..
System is 2.3.99-pre6-pre7.
I've looked at the BUGS page but i don't see this problem listed.
Further info available on request..
regards,
Paul Jakma.
Signature · 11 lines
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Systemmanagement TS T-Nova
Entwicklungszentrum Darmstadt
Heinz Mauelshagen Otto-Roehm-Strasse 71c
Senior Systems Engineer Postfach 10 05 41
64205 Darmstadt
[email protected] Germany
+49 6151 886-425
FAX-386
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-