Skip to contentSkip to conversation

trouble booting from palinux-0.5.iso on 712/80

parisc-linux Jens Trzaska 4 participants 5 messages Dec 23, 2000

lore
Share & tools
lore
#0 lore raw

Hello!
Since yesterday i'm the owner of a HP 712/80 and i've searched along the net to find an OS which is able to run on this box. When i found palinux i downloaded the palinux-0.5.iso. But the booting process doesn't seem to be successful. In the readme it says that i should get a login prompt...but i don't get the prompt. The system stops when saying:
"Switching from PDC console"

Thats all. I have a 12x Plextor cdrom booting from scsi-id 6. I also tried to boot it from scsi-id 0. The same problem. The system has 32MB RAM and Boot Rom Version 1.6. Is that perhaps a too old Boot Rom? I read that it is updateable but cannot find an updated version on the HP homepage or somewhere else. Can someone tell me where i can get an update?
I would give you the complete dmesg but i don't know how to get it out of that box...since i cannot do anything. Any idea if what is wrong with that box?

Regards Jens

#1 lore raw
Quoted 8 lines · Jens Trzaska

Hello!
Since yesterday i'm the owner of a HP 712/80 and i've searched along the net to find an OS which is able to run on this box. When i found palinux i downloaded the palinux-0.5.iso. But the booting process doesn't seem to be successful. In the readme it says that i should get a login prompt...but i don't get the prompt. The system stops when saying:
"Switching from PDC console"

This ought to be, but isn't, in the FAQ. Could someone who knows more about the 0.5 CD-ROM than I do write up the answer for the FAQ?

Basically, your kernel is using the wrong console device. try editing the command line to specify `console=tty0'.

Signature · 1 line
Revolutions do not require corporate support.
#3 lore raw
In reply to Jens Trzaska
Quoted 7 lines · Jens Trzaska

Since yesterday i'm the owner of a HP 712/80 and i've searched along the net to find an OS which is able to run on this box. When i found palinux i downloaded the palinux-0.5.iso. But the booting process doesn't seem to be successful. In the readme it says that i should get a login prompt...but i don't get the prompt. The system stops when saying:
"Switching from PDC console"

Am I right in assuming:
- you're using a graphics head (not a serial console)
- you're using the built-in graphics, not an add on card?

- Alex

Signature · 4 lines
Alex deVries, Principal Solutions Architect, The Puffins at Linuxcare
613.562.2759 tel
[email protected], http://www.linuxcare.com/
Linuxcare, Support for the revolution.
#2 lore raw
In reply to Matthew Wilcox
Quoted 9 lines · Matthew Wilcox
Quoted 7 lines · Jens Trzaska

Since yesterday i'm the owner of a HP 712/80 and i've searched along the net to find an OS which is able to run on this box. When i found palinux i downloaded the palinux-0.5.iso. But the booting process doesn't seem to be successful. In the readme it says that i should get a login prompt...but i don't get the prompt. The system stops when saying:
"Switching from PDC console"

Quoted 5 lines

This ought to be, but isn't, in the FAQ. Could someone who knows more about the 0.5 CD-ROM than I do write up the answer for the FAQ?

Basically, your kernel is using the wrong console device. try editing the command line to specify `console=tty0'.

Hi,

I do not know much about it but running this image on a 715/100. I think he does not use serial console:
On the palinux-0.5.iso it always switches to serial console and you do not see anything more on the screen. Please use a null modem cable and plug it into first serial port of your 712 and to another PC. Then use cu, minicom, hyperterminal (for win32) or some similar terminal program to see if boot and init fail. If not you get a Login prompt on serial console and can install and afterwards after another reboot setup networking (as described in the readmes) and use ssh to connect to the box.
As far as I know no screen is supported on that image (never tried it after installing).

hope that helps.

Signature · 2 lines
Bjoern A. Zeeb				bzeeb at Zabbadoz dot NeT
56 69 73 69 74				http://www.zabbadoz.net/
#4 lore raw
In reply to Alex deVries
Quoted 10 lines · Alex deVries
Quoted 7 lines · Jens Trzaska

Since yesterday i'm the owner of a HP 712/80 and i've searched along the net to find an OS which is able to run on this box. When i found palinux i downloaded the palinux-0.5.iso. But the booting process doesn't seem to be successful. In the readme it says that i should get a login prompt...but i don't get the prompt. The system stops when saying:
"Switching from PDC console"

Quoted 3 lines

Am I right in assuming:
- you're using a graphics head (not a serial console)
- you're using the built-in graphics, not an add on card?

yep...a quit normal 14" monitor and a keyboard...
but the trick with the serial console works. I'm now working over the serial with minicom from my notebook(FreeBSD). That's o.k. It seems to run without any Problems. ethernet is running and so on. I think palinux is great work. :)

Regards Jens