Skip to contentSkip to conversation

kernel 2.4.0/1/1-ac15 and ncr53c810a

DISCUSSION Wolfgang Teichmann 3 participants 3 messages Feb 17, 2001

lore
Share & tools
lore
#0 lore raw

Hello,

I have problems using my scanner (HP C6270A connected to ncr53c810a) with xsane.

I always get the error message:

error during read: Error during device I/O

Feb 15 23:57:27 localhost kernel: Attached scsi generic sg2 at scsi0,
channel 0, id 4, lun 0, type 3
Feb 15 23:57:27 localhost kernel: ncr53c810a-0-<4,*>: target did not
report SYNC.
Feb 15 23:58:01 localhost kernel: scsi : aborting command due to timeout
: pid 0, scsi0, channel 0, id 4, lun 0 Read (6) 00 00 7b 66 00
Feb 15 23:58:01 localhost kernel: ncr53c8xx_abort: pid=0
serial_number=1099 serial_number_at_timeout=1099
Feb 15 23:58:04 localhost kernel: SCSI host 0 abort (pid 0) timed out -
resetting
Feb 15 23:58:04 localhost kernel: SCSI bus is being reset for host 0
channel 0.
Feb 15 23:58:04 localhost kernel: ncr53c8xx_reset: pid=0 reset_flags=2
serial_number=1099 serial_number_at_timeout=1099
Feb 15 23:58:04 localhost kernel: ncr53c810a-0: restart (scsi reset).

With kernel 2.2.x I have no problems accessing the scanner with xsane.

Any idea?

#1 lore raw
Quoted 5 lines · On 02.17 Wolfgang Teichmann wrote:

Hello,

I have problems using my scanner (HP C6270A connected to ncr53c810a) with xsane.

Quoted 7 lines

I always get the error message:

error during read: Error during device I/O

Feb 15 23:57:27 localhost kernel: Attached scsi generic sg2 at scsi0,

channel 0, id 4, lun 0, type 3

Try disabling 'Initiate sync negotitation' in the card BIOS for the ID of the scanner.

Signature · 4 lines
J.A. Magallon                                                      $> cd pub
mailto:[email protected]                                          $> more beer

Linux werewolf 2.4.1-ac14 #1 SMP Thu Feb 15 16:05:52 CET 2001 i686
#2 lore raw

Hello Wolfgang & J.A. ,

Quoted 10 lines · J . A . Magallon
Quoted 7 lines · On 02.17 Wolfgang Teichmann wrote:

Hello,
I have problems using my scanner (HP C6270A connected to ncr53c810a) with xsane.
I always get the error message:
error during read: Error during device I/O

Feb 15 23:57:27 localhost kernel: Attached scsi generic sg2 at scsi0,

channel 0, id 4, lun 0, type 3

Try disabling 'Initiate sync negotitation' in the card BIOS for the ID of the scanner.

There is no Bios on an 810/810a . There is a way to tell the driver not to 'initiate Sync' & I'd prolly recommend disabling 'disconnect' as well . UNLESSS you have -any- other device on the 810's scsi bus . Please see :
linux/drivers/scsi/EADME.ncr53c8xx
Hth , JimL
+----------------------------------------------------------------+
| James W. Laferriere | System Techniques | Give me VMS |
| Network Engineer | 25416 22nd So | Give me Linux |
| [email protected] | DesMoines WA 98198 | only on AXP |
+----------------------------------------------------------------+