Skip to contentSkip to conversation

Linux 2.4.4-ac5

DISCUSSION Mourad De Clerck 1 participant 1 message May 8, 2001

lore
Share & tools
lore
#0 lore raw

Hi,

I've just tried 2.4.4ac5, and it stopped with an ext2fs error (Block bitmap for group 16 not in...) Reiserfs was compiled in the kernel too, and it too was complaining (they weren't able to mount my (ext2) root partition for some reason)

I've gone back to ac4, with an identical kernel config, and it works flawlessly...

I'm using an adaptec 2940uw - i'm assuming it's something to do with this entry in the changelog of ac5:
* Update aic7xxx to 6.1.12 (Justin Gibbs)

I'm using an epox kp6-bs, which is a bx based SMP board - i appended some output from the scsi and acpi (this is ac4)

If anyone needs more info (dmesg/kernelconfig), just ask - but please cc me as i'm not subscribed to linux-kernel

Mourad DC

SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.1.11
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Wide Channel A, SCSI Id=7, 16/255 SCBs

 Vendor: IBM       Model: DDRS-34560W       Rev: S92A
 Type:   Direct-Access                      ANSI SCSI revision: 02
 Vendor: IBM       Model: DDRS-34560W       Rev: S97B
 Type:   Direct-Access                      ANSI SCSI revision: 02
 Vendor: IBM       Model: DCAS-32160        Rev: S65A
 Type:   Direct-Access                      ANSI SCSI revision: 02
 Vendor: IOMEGA    Model: ZIP 100           Rev: J.03
 Type:   Direct-Access                      ANSI SCSI revision: 02
 Vendor: QUANTUM   Model: VIKING 2.3 WSE    Rev: 8808
 Type:   Direct-Access                      ANSI SCSI revision: 02
scsi0:0:1:0: Tagged Queuing enabled.  Depth 253
scsi0:0:2:0: Tagged Queuing enabled.  Depth 253
scsi0:0:3:0: Tagged Queuing enabled.  Depth 253
scsi0:0:9:0: Tagged Queuing enabled.  Depth 253

Attached scsi disk sda at scsi0, channel 0, id 1, lun 0 Attached scsi disk sdb at scsi0, channel 0, id 2, lun 0 Attached scsi disk sdc at scsi0, channel 0, id 3, lun 0 Attached scsi removable disk sdd at scsi0, channel 0, id 4, lun 0 Attached scsi disk sde at scsi0, channel 0, id 9, lun 0 (scsi0:A:1): 40.000MB/s transfers (20.000MHz, offset 8, 16bit) SCSI device sda: 8925000 512-byte hdwr sectors (4570 MB) Partition check:
/dev/scsi/host0/bus0/target1/lun0: p1 p2 < p5 p6 > (scsi0:A:2): 40.000MB/s transfers (20.000MHz, offset 8, 16bit) SCSI device sdb: 8925000 512-byte hdwr sectors (4570 MB) /dev/scsi/host0/bus0/target2/lun0: p1
(scsi0:A:3): 20.000MB/s transfers (20.000MHz, offset 15) SCSI device sdc: 4226725 512-byte hdwr sectors (2164 MB) /dev/scsi/host0/bus0/target3/lun0: p1 p2 p3
SCSI device sdd: 196608 512-byte hdwr sectors (101 MB)
sdd: Write Protect is off /dev/scsi/host0/bus0/target4/lun0: p4
(scsi0:A:9): 40.000MB/s transfers (20.000MHz, offset 8, 16bit) SCSI device sde: 4446801 512-byte hdwr sectors (2277 MB) /dev/scsi/host0/bus0/target9/lun0: p1
ACPI-0411: *** Warning: Reference \_PR_.CPU0 at AML 903 not found
ACPI: Core Subsystem version [20010427]
ACPI: Subsystem enabled