tulip driver BROKEN in 2.4.5-pre4
Could you post the output of
#tulip-diag -mm -aa -f
with the broken driver?
Some code that's required for Linksys Tulip clones was moved from pnic specific part into the generic part, perhaps that causes problems.
--
Manfred
Quoted 7 lines · Studierende der Universitaet des Saarlandes
Could you post the output of
#tulip-diag -mm -aa -f
with the broken driver?
Some code that's required for Linksys Tulip clones was moved from pnic specific part into the generic part, perhaps that causes problems.
i have a 21041 dec tulip which has failed to work with linux-2.4.5-pre[3-5] kernel drivers. (it also fails with the sourceforge devel version tulip-1.1.7)
it appears that the card gets lodged in full duplex mode. however, this could just be a superficial syndrome.
anyhow, here is the output of tulip-diag -mm -aa -f from the *broken* driver
tulip-diag.c:v2.06 1/8/2001 Donald Becker ([email protected])
http://www.scyld.com/diag/index.html
Index #1: Found a Digital DS21140 Tulip adapter at 0xfc00. Digital DS21140 Tulip chip registers at 0xfc00:
0x00: fff88000 ffffffff ffffffff 03421000 03421200 fc000102 e3840000 fffe0000 0x40: fffe0000 ffffdff0 ffffffff fffe0000 ffffff59 ffffffff 1c09fdc0 fffffec8 Port selection is 100mbps-SYM/PCS 100baseTx scrambler, half-duplex. Transmit stopped, Receive stopped, half-duplex.
The Rx process state is 'Stopped'.
The Tx process state is 'Stopped'.
The transmit threshold is 128.
No MII transceivers found!
Index #2: Found a Digital DC21041 Tulip adapter at 0xf080. Digital DC21041 Tulip chip registers at 0xf080:
0x00: ffe08000 ffffffff ffffffff 0ee4e000 0ee4e200 fc000112 fffe0200 fffe0000 0x40: fffe0000 ffff4bf8 ffffffff fffe0000 000050c8 ffffef01 ffffffff ffff0008 Port selection is full-duplex.
Transmit stopped, Receive stopped, full-duplex.
The Rx process state is 'Stopped'.
The Tx process state is 'Stopped'.
The transmit unit is set to store-and-forward.
The NWay status register is 000050c8.
No MII transceivers found!
Internal autonegotiation state is 'Negotiation complete'.
and here is one working dump for comparison (driver 0.9.14 from sourceforge)
tulip-diag.c:v2.06 1/8/2001 Donald Becker ([email protected])
http://www.scyld.com/diag/index.html
Index #1: Found a Digital DS21140 Tulip adapter at 0xfc00. Digital DS21140 Tulip chip registers at 0xfc00:
0x00: fff88000 ffffffff ffffffff 03421000 03421200 fc000102 e3840000 fffe0000 0x40: fffe0000 fff597ff ffffffff fffe0000 ffffff59 ffffffff 1c09fdc0 fffffec8 Port selection is 100mbps-SYM/PCS 100baseTx scrambler, half-duplex. Transmit stopped, Receive stopped, half-duplex.
The Rx process state is 'Stopped'.
The Tx process state is 'Stopped'.
The transmit threshold is 128.
No MII transceivers found!
Index #2: Found a Digital DC21041 Tulip adapter at 0xf080. Digital DC21041 Tulip chip registers at 0xf080:
0x00: ffe08000 ffffffff ffffffff 0ee4e000 0ee4e200 fc660000 fffe2002 ffffebef 0x40: fffe0000 ffff03ff ffffffff fffe0000 000001c8 ffffef05 ffffff3f ffff0008 Port selection is half-duplex.
Transmit started, Receive started, half-duplex.
The Rx process state is 'Waiting for packets'.
The Tx process state is 'Idle'.
The transmit unit is set to store-and-forward.
The NWay status register is 000001c8.
No MII transceivers found!
Internal autonegotiation state is 'Autonegotiation disabled'.
Signature · 3 lines
J o h a n K u l l s t a m [[email protected]] Don't Fear the Penguin!