Skip to contentSkip to conversation

Promise Ultra100 TX2 pbm

DISCUSSION Andre Hedrick 1 participant 1 message May 30, 2001 1 message not in the archive

lore
Share & tools
lore
#1 lore raw
In reply to a message not in the archive

Until I get some feed back that my patches will be accepted, there are a lot of fixes and updates on hold.

Promise Ultra100 TX2, AMD760(MP), OSB4/CSB5.

Right now there is a 2.2.19 patch and that is it.

Since there are changes being made without understand the total scope of the issues at hand, one should expect more problems not less in the future.

When I finish adding 48-lba addressing, I will post a patch for 2.4.5 but they will no longer be split up. There are to many reports of problems an the next patches will only be complete solutions to correct the current kludge mess that we have.

Cheers,

Quoted 90 lines · Frederic Soulier

Hi Andre,

Sorry to bother you, I know your time is precious, so pls feel free to send this
to /dev/null if you don't have time :)

I was wondering if the patch you issued on the 9th of April would fix this problem.
I cannot set -d1 flag on the 2 disks on the Promise Ultra100 TX2

The throughput of my 2 hard disks on my Promise Controler is ridiculous...

# hdparm -t /dev/hda

/dev/hda:
Timing buffered disk reads: 64 MB in 2.87 seconds = 22.30 MB/sec

# hdparm -t /dev/hde

/dev/hde:
Timing buffered disk reads: 64 MB in 38.04 seconds = 1.68 MB/sec

# hdparm -t /dev/hdg

/dev/hdg:
Timing buffered disk reads: 64 MB in 37.13 seconds = 1.72 MB/sec

.. maybe the reason is that I cannot set DMA for hde and hdf. I do not understand.

# hdparm -d1 /dev/hde
   /dev/hde:
    setting using_dma to 1 (on)
    HDIO_SET_DMA failed: Operation not permitted
    using_dma    =  0 (off)
# hdparm -d1 /dev/hdg
   /dev/hdg:
    setting using_dma to 1 (on)
    HDIO_SET_DMA failed: Operation not permitted
    using_dma    =  0 (off)

Any help appreciated.
Thanks
Fred

3 hard disks:-
(A) 1 IBM 37Gb ATA/66 on ide0 onboard controler
(B) 1 IBM 41Gb GXP60 ATA/100 on ide2 promise controler Ultra100 TX2
(C) 1 IBM 25Gb ATA/66 on ide3 promise controler Ultra100 TX2

hdparm settings are:

/dev/hda (A)
------------
/dev/hda:

    multcount    = 16 (on)
    I/O support  =  3 (32-bit w/sync)
    unmaskirq    =  1 (on)
    using_dma    =  1 (on)
    keepsettings =  0 (off)
    nowerr       =  0 (off)
    readonly     =  0 (off)
    readahead    =  8 (on)

geometry = 4160/255/63, sectors = 66835440, start = 0

/dev/hde (B)
------------
/dev/hde:

    multcount    = 16 (on)
    I/O support  =  3 (32-bit w/sync)
    unmaskirq    =  1 (on)
    using_dma    =  0 (off)
    keepsettings =  0 (off)
    nowerr       =  0 (off)
    readonly     =  0 (off)
    readahead    =  8 (on)
    geometry     = 79780/16/63, sectors = 80418240, start = 0

/dev/hdg (C)
------------
/dev/hdg:

Quoted 10 lines
    multcount    = 16 (on)
    I/O support  =  3 (32-bit w/sync)
    unmaskirq    =  1 (on)
    using_dma    =  0 (off)
    keepsettings =  0 (off)
    nowerr       =  0 (off)
    readonly     =  0 (off)   
    readahead    =  8 (on)
    geometry     = 53040/16/63, sectors = 53464320, start = 0

Andre Hedrick
Linux ATA Development
ASL Kernel Development
-----------------------------------------------------------------------------

ASL, Inc.                                     Toll free: 1-877-ASL-3535
1757 Houret Court                             Fax: 1-408-941-2071
Milpitas, CA 95035                            Web: www.aslab.com