0.9ser can't install on D210
please help,
i can't load linux pa-risc 0.9seriell on my HP9000/D210. Why?
(HP-UX 10.20 is running....)
Jan Heumann
[email protected]
-----------------------------------------------------
Main Menu: Enter command > search
Searching for potential boot device(s)... This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path (dec) Device Type ----------- ----------------- ----------- P0 4.5 Random access media P1 4.8 Random access media P2 16/5.2 Random access media P3 16/6.0 LAN Module
Main Menu: Enter command > boot p2 Interact with IPL (Y or N)?> n
Booting...
Boot IO Dependent Code (IODC) revision 1
IPL error: bad IPL checksum.
Error Reading IPL
Main Menu: Enter command > search
Searching for potential boot device(s)... This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path (dec) Device Type ----------- ----------------- ----------- P0 4.5 Random access media P1 4.8 Random access media P2 16/5.2 Random access media P3 16/6.0 LAN Module
Main Menu: Enter command > boot p2 Interact with IPL (Y or N)?> y
Booting...
Boot IO Dependent Code (IODC) revision 1
IPL error: bad IPL checksum.
Error Reading IPL
--------------------------------------------------------
information all
PROCESSOR INFORMATION
HVERSION SVERSION CVERSION
Speed Model Model/Op (Revision)
--------- -------- -------- ---------- 100 MHz 0x4840 0x0481 12
HSC Bus Speed (in MHz) : 33
Software ID (dec) : 2009187834 Software ID (hex) : 0x77c1c5fa Software Capability : 0xf0
<Press any key to continue (q to quit)>
COPROCESSOR INFORMATION
Coprocessor Coprocessor Coprocessor
Model Revision State
----------- ----------- -------------
0x0000000d 1 Functional
CACHE INFORMATION
Instruction Cache Size Data Cache Size
----------------------- ---------------
128 KB 128 KB
<Press any key to continue (q to quit)>
MEMORY INFORMATION
Slot Card Size Amount Enabled
---- --------- --------------
0 64 MB 64 MB
1 64 MB 64 MB
2 64 MB 64 MB
3 64 MB 64 MB
4 64 MB 64 MB
5 64 MB 64 MBPhysical Memory: 384 MB (0x18000000) Configured Memory: 384 MB (0x18000000)
<Press any key to continue (q to quit)>
I/O MODULE INFORMATION
IODC
IODC
Path (dec) Type Slot Mod HVERSION SVERSION Vers
Dep
---- ---- ---- --- -------- ---------- ------
------
4 A DMA I/O 1 0 0x0131 0x00008980 0x070x00
16 Bus Adapter 4 0 0x02e0 0x00008100 0x000x00
16/4 Built-in RS232 1 0 0x02e0 0x00008c00 0x010x00
16/5 Built-in SE SCSI 1 1 0x02e0 0x00008200 0x010x00
16/6 Built-in LAN 1 2 0x02e0 0x00008a00 0x020x00
16/0 Built-in Parallel 0 0 0x02e0 0x00007400 0x000x00
16/7 Built-in Keyboard 1 3 0x02e0 0x00008400 0x000x00
16/8 Built-in Mouse 2 0 0x02e0 0x00008400 0x000x00
20 Bus Adapter 5 0 0x0300 0x00008e00 0x000x00
20/2 RS232 Port 0 2 0x0300 0x00008c00 0x010x00
20/5 Bus Adapter 1 1 0x0300 0x00009000 0x000x00
<Press any key to continue (q to quit)>
Hot Swap module is present.
EISA Cards
Path Type EISA ID ---- ---- ------- 20/5/1 EISA card 0x25d00400 20/5/2 EISA slot is empty 20/5/3 EISA slot is empty 20/5/4 EISA slot is empty
<Press any key to continue (q to quit)>
BOOT INFORMATION
Autoboot: ON Autosearch: ON Fastboot: OFF
Primary boot path: 4.8 (dec)
04.8 (hex)
Alternate boot path: 16/5.2 (dec)
10/05.2 (hex)
Console path: 16/4.0 (dec)
10/04.0 (hex)
Keyboard path: 16/7.0 (dec)
10/07.0 (hex)LAN Station Address: 080009-af13c8
Mon Jan 5 21:15:36 GMT 1970 (19:70:01:05:21:15:36)
<Press any key to continue (q to quit)>
FIRMWARE INFORMATION
Firmware Version: 36.34
CHIP REVISIONS
Module Revision ------ -------- System Board 0 Processor Board 2 PA 7100LC 12 Firmware 20 Fast/Wide SCSI Board 1 Multifunction I/O Controller 0 EISA Interface 0
<Press any key to continue (q to quit)>
WARNINGS
No warnings to report.
Information Menu: Enter command >
Quoted 4 lines · On Tue, Jun 05, 2001 at 12:23:14PM +0200, [email protected] wrote:
please help,
i can't load linux pa-risc 0.9seriell on my HP9000/D210. Why?
You will see from <http://parisc-linux.org/release-0.9/systems.html>
that D series machines have not been tested. However, your problem looks more like trouble reading the CD. Can you mount the CD on some other system and see the contents, just to check the CD is burned properly?
Alternatively you could try a network boot, as described in the README on the CD.
Richard
Quoted 34 lines
(HP-UX 10.20 is running....)
Jan Heumann
[email protected]
-----------------------------------------------------
Main Menu: Enter command > searchSearching for potential boot device(s)...
This may take several minutes.To discontinue search, press any key (termination may not be immediate).
Path Number Device Path (dec) Device Type ----------- ----------------- ----------- P0 4.5 Random access media P1 4.8 Random access media P2 16/5.2 Random access media P3 16/6.0 LAN ModuleMain Menu: Enter command > boot p2
Interact with IPL (Y or N)?> nBooting...
Boot IO Dependent Code (IODC) revision 1IPL error: bad IPL checksum.
Error Reading IPL
Main Menu: Enter command > search
Quoted 6 lines · On Tue, Jun 05, 2001 at 12:23:14PM +0200, [email protected] wrote:
Booting...
Boot IO Dependent Code (IODC) revision 1IPL error: bad IPL checksum.
Error Reading IPL
did you use cdrecord -isosize to burn the CD ? I have the same problem and that's the only option, which I probably haven't used, when burning the 0.5 ISO. I'll try to burn a cd without using -isosize, when I get home this evening.
Thomas.
All -
OR, you might:
$>gunzip whatever.CD.ISO.gz
#>losetup /dev/loop0 ${whatever_path}/watever.CD.ISO #>$mount -r -t iso9660 /dev/loop0 /somewhere
now you can browse the CD image to your hearts content. also you can mount upto ten of these things (loop0-loop9) at the same time.
Of course, you did build your kernel with the "loop device" and "iso9660 filesystem support" didn't you?
PS: You can use similar commands to browse (and modify) your ramdisk.bin files.
Mike
Quoted 5 lines · Richard Hirst
Quoted 4 lines · On Tue, Jun 05, 2001 at 12:23:14PM +0200, [email protected] wrote:
please help,
=20
i can't load linux pa-risc 0.9seriell on my HP9000/D210. Why?
Quoted 25 lines
=20
You will see from <http://parisc-linux.org/release-0.9/systems.html>
that D series machines have not been tested. However, your problem looks more like trouble reading the CD. Can you mount the CD on some other system and see the contents, just to check the CD is burned properly?
=20
Alternatively you could try a network boot, as described in the README on the CD.
=20
Richard
=20
=20Quoted 12 lines
=20
(HP-UX 10.20 is running....)
=20
Jan Heumann
[email protected]
-----------------------------------------------------
Main Menu: Enter command > search
=20
Searching for potential boot device(s)...
This may take several minutes.
=20
To discontinue search, press any key (termination may not be immediat=
e).
Quoted 28 lines
Quoted 9 lines
=20
=20
=20Path Number Device Path (dec) Device Type ----------- ----------------- ----------- P0 4.5 Random access media P1 4.8 Random access media P2 16/5.2 Random access media P3 16/6.0 LAN ModuleQuoted 13 lines
=20
=20
Main Menu: Enter command > boot p2
Interact with IPL (Y or N)?> n
=20
Booting...
Boot IO Dependent Code (IODC) revision 1
=20
IPL error: bad IPL checksum.
=20
Error Reading IPL
=20
Main Menu: Enter command > search=20
=20
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/cgi-bin/mailman/listinfo/parisc-linux
Quoted 4 lines · Thomas Bogendoerfer
Quoted 3 lines · On Tue, Jun 05, 2001 at 12:23:14PM +0200, [email protected] wrote:
Booting...
Boot IO Dependent Code (IODC) revision 1
Quoted 8 lines
Quoted 3 lines
IPL error: bad IPL checksum.
Error Reading IPL
did you use cdrecord -isosize to burn the CD ? I have the same problem and that's the only option, which I probably haven't used, when burning the 0.5 ISO. I'll try to burn a cd without using -isosize, when I get home this evening.
ok, without -isosize the CDs are working perfect. I've diffed the broken CDs against the images and there are differences in the first sector. I'm using cdrecord 1.8.1 just for the record.
Thomas.
Signature · 2 lines
Crap can work. Given enough thrust pigs will fly, but it's not necessary a good idea. [ Alexander Viro on linux-kernel ]
the problem is over.
i have probe the iso image 0.9ser from ESIEE. this will not work on my D210 and 712-60.
i have download the image from
http://puffin.external.hp.com/pub/parisc/cd-images/palinux-0.9-32serial.iso.gz
and this work.