Skip to contentSkip to conversation

Illegal instruction

DISCUSSION Carsten Langgaard 10 participants 23 messages Jul 6, 2001 – Jul 19, 2001 MIPS

lore
Share & tools
lore
#0 lore raw

Hi Karel,

I have tried the root-images tar-files: mipselroot-rh7-20010606 and mipsroot-rh7.
The mipsroot-rh7 (bigendian) root image seem to work fine, but when I use the mipselroot-rh7-20010606 (littleendian) I get an illegal instruction.
[cat:179] Illegal instruction 7c010001 at 2ac8b20c ra=00000000.

I'm using a 2.4.3 kernel.
Anyone got an idea ?

/Carsten

--

_    _ ____  ___   Carsten Langgaard   Mailto:[email protected]
|\  /|||___)(___   MIPS Denmark        Direct: +45 4486 5527
| \/ |||    ____)  Lautrupvang 4B      Switch: +45 4486 5555
  TECHNOLOGIES     2750 Ballerup       Fax...: +45 4486 5556
                   Denmark             http://www.mips.com
#1 lore raw
Quoted 9 lines · Carsten Langgaard

I have tried the root-images tar-files: mipselroot-rh7-20010606 and mipsroot-rh7.
The mipsroot-rh7 (bigendian) root image seem to work fine, but when I use the mipselroot-rh7-20010606 (littleendian) I get an illegal instruction.
[cat:179] Illegal instruction 7c010001 at 2ac8b20c ra=00000000.

I'm using a 2.4.3 kernel.
Anyone got an idea ?

I'm still using 2.4.0-test9 on mipsel, because I've problems with the newer kernels too. I hope to test H.J. Lu's toolchain/glibc, but currently it is much to hot to switch on extra computers :-)

Regards,

Signature · 6 lines
Karel van Houten

----------------------------------------------------------
The box said "Requires Windows 95 or better."
I can't understand why it won't work on my Linux computer. 
----------------------------------------------------------
#2 lore raw
Quoted 3 lines · Houten K.H.C. van (Karel)

I'm still using 2.4.0-test9 on mipsel, because I've problems with the newer kernels too. I hope to test H.J. Lu's toolchain/glibc, but currently it is much to hot to switch on extra computers :-)

Weird, I'm using 2.4.5 for more than a week now on my /240 and it appears
to work fine. I've built it with my old tools which I'm still using.

Signature · 3 lines
+  Maciej W. Rozycki, Technical University of Gdansk, Poland   +
+--------------------------------------------------------------+
+        e-mail: [email protected], PGP key available        +
#3 lore raw
In reply to Carsten Langgaard

Hello Carsten,

I have seen the same thing on the same kernel version.

Dan Aizenstros
Software Engineer
V3 Semiconductor Corp.

Quoted 21 lines · Carsten Langgaard

Hi Karel,

I have tried the root-images tar-files: mipselroot-rh7-20010606 and mipsroot-rh7.
The mipsroot-rh7 (bigendian) root image seem to work fine, but when I use the mipselroot-rh7-20010606 (littleendian) I get an illegal instruction.
[cat:179] Illegal instruction 7c010001 at 2ac8b20c ra=00000000.

I'm using a 2.4.3 kernel.
Anyone got an idea ?

/Carsten

--

_    _ ____  ___   Carsten Langgaard   Mailto:[email protected]
|\  /|||___)(___   MIPS Denmark        Direct: +45 4486 5527
| \/ |||    ____)  Lautrupvang 4B      Switch: +45 4486 5555
  TECHNOLOGIES     2750 Ballerup       Fax...: +45 4486 5556
                   Denmark             http://www.mips.com
#4 lore raw
In reply to Carsten Langgaard
Quoted 10 lines · Carsten Langgaard

Hi Karel,

I have tried the root-images tar-files: mipselroot-rh7-20010606 and mipsroot-rh7.
The mipsroot-rh7 (bigendian) root image seem to work fine, but when I use the mipselroot-rh7-20010606 (littleendian) I get an illegal instruction.
[cat:179] Illegal instruction 7c010001 at 2ac8b20c ra=00000000.

Quoted 5 lines

I'm using a 2.4.3 kernel.
Anyone got an idea ?

/Carsten

Is the userland compiled with MIPS I option? I bet this is the same nasty MIPS_ATOMIC_SET bug.

Currently, there are three fixes. One is from Florian, which only takes care of CPUs with ll/sc. Another is from Maceij, which introduces a new syscall, and some changes in glibc. The thrid is mine, a compromising one. It takes care of both ll/sc case and non-llsc case, has minimum change, and practically makes all programs happy.

Ralf, please take at least one of the fixes. Even a not-so-good fix is better than no fix.

Jun

This is a compromising fix for sysmips(MIPS_ATOMIC_SET, ...). It forces SIGSYS when the return value is a small negative value. This limit is OK for glibc.

Jun

arch/mips/kernel/sysmips.c renamed from arch/mips/kernel/sysmips.c.orig +73 -43
diff -Nru linux/arch/mips/kernel/sysmips.c.orig linux/arch/mips/kernel/sysmips.c
@@ -16,7 +16,7 @@
 #include <linux/sched.h>
 #include <linux/string.h>
 #include <linux/utsname.h>
-
+#include <linux/signal.h>
 #include <asm/cachectl.h>
 #include <asm/pgalloc.h>
 #include <asm/sysmips.h>
@@ -75,53 +75,83 @@
 	}
 
 	case MIPS_ATOMIC_SET: {
-#ifdef CONFIG_CPU_HAS_LLSC
-		unsigned int tmp;
+		int *ptr, val, ret, err, tmp;
+		struct siginfo info;
 
-		p = (int *) arg1;
-		errno = verify_area(VERIFY_WRITE, p, sizeof(*p));
-		if (errno)
-			return errno;
-		errno = 0;
-
-		__asm__(".set\tpush\t\t\t# sysmips(MIPS_ATOMIC, ...)\n\t"
-			".set\tmips2\n\t"
-			".set\tnoat\n\t"
-			"1:\tll\t%0, %4\n\t"
-			"move\t$1, %3\n\t"
-			"2:\tsc\t$1, %1\n\t"
-			"beqz\t$1, 1b\n\t"
-			".set\tpop\n\t"
-			".section\t.fixup,\"ax\"\n"
-			"3:\tli\t%2, 1\t\t\t# error\n\t"
-			".previous\n\t"
-			".section\t__ex_table,\"a\"\n\t"
-			".word\t1b, 3b\n\t"
-			".word\t2b, 3b\n\t"
-			".previous\n\t"
-			: "=&r" (tmp), "=o" (* (u32 *) p), "=r" (errno)
-			: "r" (arg2), "o" (* (u32 *) p), "2" (errno)
-			: "$1");
+		ptr = (int *)arg1;
+		val = (int)arg2;
 
-		if (errno)
-			return -EFAULT;
+		/* Don't emulate unaligned accesses. */
+		if ((int)ptr & 3) {
+			info.si_signo = SIGBUS;
+                        info.si_code = BUS_ADRALN;
+			goto fault;
+		}
+
+		/* A zero here saves us three instructions. */
+		err = verify_area(VERIFY_WRITE, ptr, 0);
+		if (err) {
+                        info.si_signo = SIGSEGV;
+			info.si_code = SEGV_ACCERR;
+			goto fault;
+		}
 
-		/* We're skipping error handling etc.  */
-		if (current->ptrace & PT_TRACESYS)
-			syscall_trace();
-
-		((struct pt_regs *)&cmd)->regs[2] = tmp;
-		((struct pt_regs *)&cmd)->regs[7] = 0;
-
-		__asm__ __volatile__(
-			"move\t$29, %0\n\t"
-			"j\to32_ret_from_sys_call"
-			: /* No outputs */
-			: "r" (&cmd));
-		/* Unreached */
+#ifdef CONFIG_CPU_HAS_LLSC
+		__asm__(".set   mips2\n\t"
+			"1:\n\t"
+			"ll     %0,%5\n\t"
+	                ".set   push\n\t"
+	                ".set   noreorder\n\t"
+	                "beq    %0,%4,3f\n\t"
+	                " move  %3,%4\n"
+	                ".set   pop\n\t"
+	                "2:\n\t"
+	                "sc     %3,%1\n\t"
+	                "beqz   %3,1b\n\t"
+	                "3:\n\t"
+	                ".set   mips0\n\t"
+	                ".section .fixup,\"ax\"\n"
+	                "4:\n\t"
+	                "li     %2,%7\n\t"
+	                "j      3b\n\t"
+	                ".previous\n\t"
+	                ".section __ex_table,\"a\"\n\t"
+	                ".word  1b,4b\n\t"
+	                ".word  2b,4b\n\t"
+	                ".previous"
+	                : "=&r" (ret), "=R" (*ptr), "=r" (err), "=&r" (tmp)
+	                : "r" (val), "1" (*ptr), "2" (0), "i" (-EFAULT));
 #else
-	printk("sys_sysmips(MIPS_ATOMIC_SET, ...) not ready for !CONFIG_CPU_HAS_LLSC\n");
+		save_and_cli(tmp);
+		err = __get_user(ret, ptr);
+		if (ret != val)
+		err |= __put_user(val, ptr);    /* No fault
+                                                   unless unwriteable. */
+		restore_flags(tmp);
 #endif
+
+		if (err) {
+                        info.si_signo = SIGSEGV;
+			info.si_code = SEGV_MAPERR;
+			goto fault;
+		}
+			
+		if ( (ret < 0) && (ret >= -EMAXERRNO) ) {
+                        info.si_signo = SIGSYS;
+			info.si_code = 0;
+			goto fault;
+		}
+			
+		return ret;
+
+fault:
+		/* Go back to SYSCALL. */
+		((struct pt_regs *)&cmd)->cp0_epc -= 4;
+
+		info.si_addr = (void *)((struct pt_regs *)&cmd)->cp0_epc;
+		force_sig_info(info.si_signo, &info, current);
+
+		return 0;
 	}
 
 	case MIPS_FIXADE:
arch/mips/kernel/Makefile Mon Apr 9 00:23:34 2001 renamed from arch/mips/kernel/Makefile Mon Apr 9 00:23:08 2001 +2 -1
diff -Nur linux.orig/arch/mips/kernel/Makefile linux/arch/mips/kernel/Makefile
@@ -20,7 +20,7 @@
 obj-y                          += branch.o process.o signal.o entry.o \
                                   traps.o ptrace.o vm86.o ioport.o reset.o \
                                   semaphore.o setup.o syscall.o sysmips.o \
-                                  ipc.o scall_o32.o unaligned.o
+                                  ipc.o scall_o32.o unaligned.o fast-sysmips.o
 obj-$(CONFIG_MODULES)          += mips_ksyms.o
 
 ifdef CONFIG_CPU_R3000
@@ -69,5 +69,6 @@
 
 entry.o: entry.S
 head.o: head.S
+fast-sysmips.o: fast-sysmips.S
 
 include $(TOPDIR)/Rules.make
arch/mips/kernel/fast-sysmips.S Mon Apr 9 00:28:20 2001 renamed from arch/mips/kernel/fast-sysmips.S Thu Jan 1 01:00:00 1970 +85 -0

85 lines not on this page · raw message

arch/mips/kernel/irix5sys.h Sun Apr 8 21:21:16 2001 renamed from arch/mips/kernel/irix5sys.h Mon Apr 9 00:16:29 2001 +1 -1
diff -Nur linux.orig/arch/mips/kernel/irix5sys.h linux/arch/mips/kernel/irix5sys.h
@@ -69,7 +69,7 @@
 SYS(irix_getgid, 0)                    /* 1047  getgid()              V*/
 SYS(irix_unimp, 0)                     /* 1048  (XXX IRIX 4 ssig)     V*/
 SYS(irix_msgsys, 6)                    /* 1049  sys_msgsys            V*/
-SYS(sys_sysmips, 4)                    /* 1050  sysmips()            HV*/
+SYS(fast_sysmips, 4)                   /* 1050  sysmips()            HV*/
 SYS(irix_unimp, 0)                     /* 1051  XXX sysacct()        IV*/
 SYS(irix_shmsys, 5)                    /* 1052  sys_shmsys            V*/
 SYS(irix_semsys, 0)                    /* 1053  sys_semsys            V*/
arch/mips/kernel/syscalls.h Sun Apr 8 21:21:43 2001 renamed from arch/mips/kernel/syscalls.h Mon Apr 9 00:16:30 2001 +1 -1
diff -Nur linux.orig/arch/mips/kernel/syscalls.h linux/arch/mips/kernel/syscalls.h
@@ -163,7 +163,7 @@
 SYS(sys_writev, 3)
 SYS(sys_cacheflush, 3)
 SYS(sys_cachectl, 3)
-SYS(sys_sysmips, 4)
+SYS(fast_sysmips, 4)
 SYS(sys_ni_syscall, 0)                         /* 4150 */
 SYS(sys_getsid, 1)
 SYS(sys_fdatasync, 0)
#5 lore raw

Thanks, that did the trick.
Now I would like to try to install H.J. Lu's RedHat7.1 RPM packages. If I just do a:

    rpm -Uvh --root /mnt/harddisk *.rpm
then it fails on a lot of dependencies. If I try to force the install like this:
    rpm -Uvh --nodeps --force --root /mnt/harddisk *.rpm

then it actually install a lot of the RPMs, but still some fails, because it actually need then dependencies.
If I try to redo the above it seems to go better the second time, because a lot of the dependencies is solved (installed).
Is this really the way to install a set of RPMs like this or is there a better way?

/Carsten

Quoted 303 lines · Jun Sun
Quoted 10 lines · Carsten Langgaard

Hi Karel,

I have tried the root-images tar-files: mipselroot-rh7-20010606 and mipsroot-rh7.
The mipsroot-rh7 (bigendian) root image seem to work fine, but when I use the mipselroot-rh7-20010606 (littleendian) I get an illegal instruction.
[cat:179] Illegal instruction 7c010001 at 2ac8b20c ra=00000000.

Quoted 5 lines

I'm using a 2.4.3 kernel.
Anyone got an idea ?

/Carsten

Is the userland compiled with MIPS I option? I bet this is the same nasty MIPS_ATOMIC_SET bug.

Currently, there are three fixes. One is from Florian, which only takes care of CPUs with ll/sc. Another is from Maceij, which introduces a new syscall, and some changes in glibc. The thrid is mine, a compromising one. It takes care of both ll/sc case and non-llsc case, has minimum change, and practically makes all programs happy.

Ralf, please take at least one of the fixes. Even a not-so-good fix is better than no fix.

Jun

------------------------------------------------------------------------

This is a compromising fix for sysmips(MIPS_ATOMIC_SET, ...). It forces SIGSYS when the return value is a small negative value. This limit is OK for glibc.

Jun

diff -Nru linux/arch/mips/kernel/sysmips.c.orig linux/arch/mips/kernel/sysmips.c

arch/mips/kernel/sysmips.c Tue Jun 26 11:50:48 2001 renamed from arch/mips/kernel/sysmips.c.orig Mon Apr 23 11:32:54 2001 +73 -43
@@ -16,7 +16,7 @@
 #include <linux/sched.h>
 #include <linux/string.h>
 #include <linux/utsname.h>
-
+#include <linux/signal.h>
 #include <asm/cachectl.h>
 #include <asm/pgalloc.h>
 #include <asm/sysmips.h>
@@ -75,53 +75,83 @@
        }
 
        case MIPS_ATOMIC_SET: {
-#ifdef CONFIG_CPU_HAS_LLSC
-               unsigned int tmp;
+               int *ptr, val, ret, err, tmp;
+               struct siginfo info;
 
-               p = (int *) arg1;
-               errno = verify_area(VERIFY_WRITE, p, sizeof(*p));
-               if (errno)
-                       return errno;
-               errno = 0;
-
-               __asm__(".set\tpush\t\t\t# sysmips(MIPS_ATOMIC, ...)\n\t"
-                       ".set\tmips2\n\t"
-                       ".set\tnoat\n\t"
-                       "1:\tll\t%0, %4\n\t"
-                       "move\t$1, %3\n\t"
-                       "2:\tsc\t$1, %1\n\t"
-                       "beqz\t$1, 1b\n\t"
-                       ".set\tpop\n\t"
-                       ".section\t.fixup,\"ax\"\n"
-                       "3:\tli\t%2, 1\t\t\t# error\n\t"
-                       ".previous\n\t"
-                       ".section\t__ex_table,\"a\"\n\t"
-                       ".word\t1b, 3b\n\t"
-                       ".word\t2b, 3b\n\t"
-                       ".previous\n\t"
-                       : "=&r" (tmp), "=o" (* (u32 *) p), "=r" (errno)
-                       : "r" (arg2), "o" (* (u32 *) p), "2" (errno)
-                       : "$1");
+               ptr = (int *)arg1;
+               val = (int)arg2;
 
-               if (errno)
-                       return -EFAULT;
+               /* Don't emulate unaligned accesses. */
+               if ((int)ptr & 3) {
+                       info.si_signo = SIGBUS;
+                        info.si_code = BUS_ADRALN;
+                       goto fault;
+               }
+
+               /* A zero here saves us three instructions. */
+               err = verify_area(VERIFY_WRITE, ptr, 0);
+               if (err) {
+                        info.si_signo = SIGSEGV;
+                       info.si_code = SEGV_ACCERR;
+                       goto fault;
+               }
 
-               /* We're skipping error handling etc.  */
-               if (current->ptrace & PT_TRACESYS)
-                       syscall_trace();
-
-               ((struct pt_regs *)&cmd)->regs[2] = tmp;
-               ((struct pt_regs *)&cmd)->regs[7] = 0;
-
-               __asm__ __volatile__(
-                       "move\t$29, %0\n\t"
-                       "j\to32_ret_from_sys_call"
-                       : /* No outputs */
-                       : "r" (&cmd));
-               /* Unreached */
+#ifdef CONFIG_CPU_HAS_LLSC
+               __asm__(".set   mips2\n\t"
+                       "1:\n\t"
+                       "ll     %0,%5\n\t"
+                       ".set   push\n\t"
+                       ".set   noreorder\n\t"
+                       "beq    %0,%4,3f\n\t"
+                       " move  %3,%4\n"
+                       ".set   pop\n\t"
+                       "2:\n\t"
+                       "sc     %3,%1\n\t"
+                       "beqz   %3,1b\n\t"
+                       "3:\n\t"
+                       ".set   mips0\n\t"
+                       ".section .fixup,\"ax\"\n"
+                       "4:\n\t"
+                       "li     %2,%7\n\t"
+                       "j      3b\n\t"
+                       ".previous\n\t"
+                       ".section __ex_table,\"a\"\n\t"
+                       ".word  1b,4b\n\t"
+                       ".word  2b,4b\n\t"
+                       ".previous"
+                       : "=&r" (ret), "=R" (*ptr), "=r" (err), "=&r" (tmp)
+                       : "r" (val), "1" (*ptr), "2" (0), "i" (-EFAULT));
 #else
-       printk("sys_sysmips(MIPS_ATOMIC_SET, ...) not ready for !CONFIG_CPU_HAS_LLSC\n");
+               save_and_cli(tmp);
+               err = __get_user(ret, ptr);
+               if (ret != val)
+               err |= __put_user(val, ptr);    /* No fault
+                                                   unless unwriteable. */
+               restore_flags(tmp);
 #endif
+
+               if (err) {
+                        info.si_signo = SIGSEGV;
+                       info.si_code = SEGV_MAPERR;
+                       goto fault;
+               }
+
+               if ( (ret < 0) && (ret >= -EMAXERRNO) ) {
+                        info.si_signo = SIGSYS;
+                       info.si_code = 0;
+                       goto fault;
+               }
+
+               return ret;
+
+fault:
+               /* Go back to SYSCALL. */
+               ((struct pt_regs *)&cmd)->cp0_epc -= 4;
+
+               info.si_addr = (void *)((struct pt_regs *)&cmd)->cp0_epc;
+               force_sig_info(info.si_signo, &info, current);
+
+               return 0;
        }
 
        case MIPS_FIXADE:

------------------------------------------------------------------------
diff -Nur linux.orig/arch/mips/kernel/Makefile linux/arch/mips/kernel/Makefile

arch/mips/kernel/Makefile Mon Apr 9 00:23:34 2001 renamed from arch/mips/kernel/Makefile Mon Apr 9 00:23:08 2001 +2 -1
@@ -20,7 +20,7 @@
 obj-y                          += branch.o process.o signal.o entry.o \
                                   traps.o ptrace.o vm86.o ioport.o reset.o \
                                   semaphore.o setup.o syscall.o sysmips.o \
-                                  ipc.o scall_o32.o unaligned.o
+                                  ipc.o scall_o32.o unaligned.o fast-sysmips.o
 obj-$(CONFIG_MODULES)          += mips_ksyms.o
 
 ifdef CONFIG_CPU_R3000
@@ -69,5 +69,6 @@
 
 entry.o: entry.S
 head.o: head.S
+fast-sysmips.o: fast-sysmips.S
 
 include $(TOPDIR)/Rules.make

diff -Nur linux.orig/arch/mips/kernel/fast-sysmips.S linux/arch/mips/kernel/fast-sysmips.S

arch/mips/kernel/fast-sysmips.S Mon Apr 9 00:28:20 2001 renamed from arch/mips/kernel/fast-sysmips.S Thu Jan 1 01:00:00 1970 +85 -0
@@ -0,0 +1,85 @@
+/*
+ * MIPS_ATOMIC_SET asm implementation for ll/sc capable cpus
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2001 Florian Lohoff <[email protected]>
+ *
+ */
+#include <asm/asm.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+#include <asm/isadep.h>
+#include <asm/unistd.h>
+#include <asm/sysmips.h>
+#include <asm/offset.h>
+#include <asm/errno.h>
+
+#define PT_TRACESYS     0x00000002
+
+       EXPORT(fast_sysmips)
+
+       .set    noreorder
+
+       li      t0, MIPS_ATOMIC_SET
+       beq     a0, t0, 1f
+        nop
+       j       sys_sysmips
+        nop
+
+1:
+
+       # a0 - MIPS_ATOMIC_SET
+       # a1 - mem ptr
+       # a2 - value
+
+       addiu   sp, sp, -8                      # Reserve space
+       sw      a0, (sp)                        # Save arg0
+
+       addiu   a0, a1, 4                       # addr+size
+       ori     v0, a1, 4                       # addr | size
+       lw      v1, THREAD_CURDS(gp)            # current->thread.current_ds
+       or      v0, v0, a0                      # addr | size | (addr+size)
+       and     v1, v1, v0                      # (mask)&(addr | size | (addr+size)
+       bltz    v1, 5f
+        nop
+
+2:
+       ll      v0, (a1)
+       move    t0, a2
+       sc      t0, (a1)
+       beqz    t0, 2b
+        nop
+
+       sw      v0, PT_R2+8(sp)                 # Result value
+       sw      zero, PT_R7+8(sp)               # Success indicator
+
+       lw      t0, TASK_PTRACE(gp)             # syscall tracing enabled?
+       andi    t0, PT_TRACESYS
+       bnez    t0, 3f
+        nop
+
+4:
+       lw      a0, (sp)                        # Restore arg0
+       addiu   sp, sp, 8                       # Restore sp
+
+       j       o32_ret_from_sys_call
+        nop
+
+3:
+       sw      ra, 4(sp)
+       jal     syscall_trace
+        nop
+       lw      ra, 4(sp)
+       j       4b
+        nop
+
+5:
+       lw      a0, (sp)                        # Restore arg0
+       addiu   sp, sp, 8                       # Restore sp
+       j       ra
+        li     v0, -EFAULT
+

diff -Nur linux.orig/arch/mips/kernel/irix5sys.h linux/arch/mips/kernel/irix5sys.h

arch/mips/kernel/irix5sys.h Sun Apr 8 21:21:16 2001 renamed from arch/mips/kernel/irix5sys.h Mon Apr 9 00:16:29 2001 +1 -1
@@ -69,7 +69,7 @@
 SYS(irix_getgid, 0)                    /* 1047  getgid()              V*/
 SYS(irix_unimp, 0)                     /* 1048  (XXX IRIX 4 ssig)     V*/
 SYS(irix_msgsys, 6)                    /* 1049  sys_msgsys            V*/
-SYS(sys_sysmips, 4)                    /* 1050  sysmips()            HV*/
+SYS(fast_sysmips, 4)                   /* 1050  sysmips()            HV*/
 SYS(irix_unimp, 0)                     /* 1051  XXX sysacct()        IV*/
 SYS(irix_shmsys, 5)                    /* 1052  sys_shmsys            V*/
 SYS(irix_semsys, 0)                    /* 1053  sys_semsys            V*/

diff -Nur linux.orig/arch/mips/kernel/syscalls.h linux/arch/mips/kernel/syscalls.h

arch/mips/kernel/syscalls.h Sun Apr 8 21:21:43 2001 line 169

Quoted 8 lines
arch/mips/kernel/syscalls.h Sun Apr 8 21:21:43 2001 renamed from arch/mips/kernel/syscalls.h Mon Apr 9 00:16:30 2001 +1 -1
@@ -163,7 +163,7 @@
 SYS(sys_writev, 3)
 SYS(sys_cacheflush, 3)
 SYS(sys_cachectl, 3)
-SYS(sys_sysmips, 4)
+SYS(fast_sysmips, 4)
 SYS(sys_ni_syscall, 0)                         /* 4150 */
 SYS(sys_getsid, 1)
 SYS(sys_fdatasync, 0)

--

_    _ ____  ___   Carsten Langgaard   Mailto:[email protected]
|\  /|||___)(___   MIPS Denmark        Direct: +45 4486 5527
| \/ |||    ____)  Lautrupvang 4B      Switch: +45 4486 5555
  TECHNOLOGIES     2750 Ballerup       Fax...: +45 4486 5556
                   Denmark             http://www.mips.com
#6 lore raw
Quoted 4 lines · Carsten Langgaard

Thanks, that did the trick.
Now I would like to try to install H.J. Lu's RedHat7.1 RPM packages. If I just do a:

    rpm -Uvh --root /mnt/harddisk *.rpm

Those rpms have to be installed in the right order. I have a set up to do that. I will see what I can do.

H.J.

#7 lore raw
Quoted 8 lines · H . J . Lu
Quoted 4 lines · Carsten Langgaard

Thanks, that did the trick.
Now I would like to try to install H.J. Lu's RedHat7.1 RPM packages. If I just do a:

    rpm -Uvh --root /mnt/harddisk *.rpm

Those rpms have to be installed in the right order. I have a set up to do that. I will see what I can do.

Thanks, please do.
Another thing, I can see your distribution is lacking kernel header files, I guess they are needed to do a native compile of the source RPMs.

Are you only cross compiling the RPMs.
It would be great, if you could put together a RPM containing the kernel header files.

Quoted 2 lines

H.J.

--

_    _ ____  ___   Carsten Langgaard   Mailto:[email protected]
|\  /|||___)(___   MIPS Denmark        Direct: +45 4486 5527
| \/ |||    ____)  Lautrupvang 4B      Switch: +45 4486 5555
  TECHNOLOGIES     2750 Ballerup       Fax...: +45 4486 5556
                   Denmark             http://www.mips.com
#8 lore raw

Updates on RedHat 7.1/mips

Quoted 9 lines · Carsten Langgaard
Quoted 6 lines · H . J . Lu
Quoted 3 lines

Now I would like to try to install H.J. Lu's RedHat7.1 RPM packages. If I just do a:

    rpm -Uvh --root /mnt/harddisk *.rpm

Those rpms have to be installed in the right order. I have a set up to do that. I will see what I can do.

Thanks, please do.

They are in install.tar.bz2 now.

Quoted 2 lines

Another thing, I can see your distribution is lacking kernel header files, I guess they are needed to do a native compile of the source RPMs.

I added gdb and kernel-headers. I also updated gcc, glibc and binutils. The toolchain rpms are updated.

H.J.
------
My mini-port of RedHat 7.1 is at

ftp://oss.sgi.com/pub/linux/mips/redhat/7.1/

you should be able to put a small RedHat 7.1 on the mips/mipsel box and compile the rest of RedHat 7.1 yourselves.

Here are something you should know:

1. The cross compiler hosted on RedHat 7.1/ia32 is provided as a toolchain rpm. The binary rpms for the mips and mipsel cross compilers are included. You will need glibc 2.2.3-11 or above to use those rpms. The glibc x86 binary rpms under RPMS/i386 should be ok.
2. You have to find a way to put those rpms on your machine. I use network boot and NFS root to do it.
3. install.tar.bz2 has some scripts to prepare NFS root and install RedHat 7.1 on a hard drive.

Thanks.

H.J.

#9 lore raw

Re: Updates on RedHat 7.1/mips

Quoted 6 lines · H . J . Lu
Quoted 5 lines · Carsten Langgaard
Quoted 4 lines · H . J . Lu
Quoted 3 lines

Now I would like to try to install H.J. Lu's RedHat7.1 RPM packages. If I just do a:

    rpm -Uvh --root /mnt/harddisk *.rpm
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines

Those rpms have to be installed in the right order. I have a set up to do that. I will see what I can do.

Thanks, please do.

They are in install.tar.bz2 now.

Thanks a lot, that look like something we have been needing for a long time

Quoted 5 lines
Quoted 2 lines

Another thing, I can see your distribution is lacking kernel header files, I guess they are needed to do a native compile of the source RPMs.

I added gdb and kernel-headers. I also updated gcc, glibc and binutils. The toolchain rpms are updated.

Now that I'm at it :-)
Could you add a Perl rpm to you distribution, this also seems to be needed to build the RPMs natively.

I also would like to do a cross build, but how do I do that ?
Do I have to change all the spec files, to set the target arch to MIPS, or is there a easier and better way to do that ?
I guess if I just install the SRPMs and the cross toolchain, and try to build out of that I will simply build for the build platform, which is i386.

Quoted 25 lines

H.J.
------
My mini-port of RedHat 7.1 is at

ftp://oss.sgi.com/pub/linux/mips/redhat/7.1/

you should be able to put a small RedHat 7.1 on the mips/mipsel box and compile the rest of RedHat 7.1 yourselves.

Here are something you should know:

1. The cross compiler hosted on RedHat 7.1/ia32 is provided as a toolchain rpm. The binary rpms for the mips and mipsel cross compilers are included. You will need glibc 2.2.3-11 or above to use those rpms. The glibc x86 binary rpms under RPMS/i386 should be ok.
2. You have to find a way to put those rpms on your machine. I use network boot and NFS root to do it.
3. install.tar.bz2 has some scripts to prepare NFS root and install RedHat 7.1 on a hard drive.

Thanks.

H.J.

#10 lore raw

Re: Updates on RedHat 7.1/mips

Quoted 2 lines · Carsten Langgaard

Could you add a Perl rpm to you distribution, this also seems to be needed to build the RPMs natively.

Perl has to be built natively. I uploaded mysql-3.23.36-1.1.src.rpm, perl-5.6.0-12.1.src.rpm, apache-1.3.19-5.src.rpm, mod_perl-1.24_01-2.src.rpm, tcsh-6.10-5.src.rpm and zsh-3.0.8-8.src.rpm. Just installed my RedHat 7.1. Then you can build perl yourself. You may need to build/install the tcsh rpm first.

Quoted 6 lines

I also would like to do a cross build, but how do I do that ?
Do I have to change all the spec files, to set the target arch to MIPS, or is there a easier and better way to do that ?
I guess if I just install the SRPMs and the cross toolchain, and try to build out of that I will simply build for the build platform, which is i386.

You need my patched `rpm' to do cross build. You also need some specicial set up. I am enclosng a message of mine. I will see if I can cleanup my cross build environment and upload it.

H.J.
-----

Quoted 10 lines

they work great! Thanks for all your hard work. Now, I would like to be able to build some RPMs as well. I have never cross-built RPMs before. I took the SRPMS for make and tried:

   rpm -ba make.spec --target=mipsel

This did not do anything and built nothing. Is there a FAQ that I can read on cross building RPMS in addition to the documentation on http://www.rpm.org/ ? Do you have any quick pointers? Thanks again.

Although my source rpms do support cross compile, FYI, all my mips/mipsel rpms are cross compiled from ia32 machines, the unpatched rpm, that is /bin/rpm, doesn't support cross compile. In my RedHat 7.1, there are i386 rpm binaries which support cross compile. I have a setup to cross build rpms to mips/mipsel. Make sure your rpm sees

%__ar                   %{_target_prefix}-linux-ar
%__as                   %{_target_prefix}-linux-as
%__cc                   %{_target_prefix}-linux-gcc
%__cxx                  %{_target_prefix}-linux-c++
%__ld                   %{_target_prefix}-linux-ld
%__nm                   %{_target_prefix}-linux-nm
%__objcopy              %{_target_prefix}-linux-objcopy
%__objdump              %{_target_prefix}-linux-objdump
%__ranlib               %{_target_prefix}-linux-ranlib
%__strip                %{_target_prefix}-linux-strip

and do

# rpm --target=mips --define '_target_prefix mips'

or

# rpm --target=mipsel --define '_target_prefix mipsel'

BTW, you alao need to rebuild binutils with

# rpm --define 'ENABLE_ALL_TARGETS 1' -ta binutils-2.11.90.0.23.tar.gz

H.J.

#12 lore raw

Re: Updates on RedHat 7.1/mips

In reply to Daniel Jacobowitz
Quoted 10 lines · Daniel Jacobowitz
Quoted 6 lines

Perl has to be built natively. I uploaded mysql-3.23.36-1.1.src.rpm, perl-5.6.0-12.1.src.rpm, apache-1.3.19-5.src.rpm, mod_perl-1.24_01-2.src.rpm, tcsh-6.10-5.src.rpm and zsh-3.0.8-8.src.rpm. Just installed my RedHat 7.1. Then you can build perl yourself. You may need to build/install the tcsh rpm first.

It's not yet available for MIPS (later this week), but MontaVista Journeyman contains the patches to cross-compile Perl. It's not pretty, though.

That is a reason why I didn't bother with cross-compile Perl :-). The next thing on my todo list is to cross compile XFree86 :-(.

H.J.

#11 lore raw

Re: Updates on RedHat 7.1/mips

In reply to H . J . Lu
Quoted 9 lines · H . J . Lu
Quoted 2 lines · Carsten Langgaard

Could you add a Perl rpm to you distribution, this also seems to be needed to build the RPMs natively.

Perl has to be built natively. I uploaded mysql-3.23.36-1.1.src.rpm, perl-5.6.0-12.1.src.rpm, apache-1.3.19-5.src.rpm, mod_perl-1.24_01-2.src.rpm, tcsh-6.10-5.src.rpm and zsh-3.0.8-8.src.rpm. Just installed my RedHat 7.1. Then you can build perl yourself. You may need to build/install the tcsh rpm first.

It's not yet available for MIPS (later this week), but MontaVista Journeyman contains the patches to cross-compile Perl. It's not pretty, though.

Signature · 2 lines
Daniel Jacobowitz                           Carnegie Mellon University
MontaVista Software                         Debian GNU/Linux Developer
#13 lore raw

Re: Updates on RedHat 7.1/mips

In reply to H . J . Lu

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 7 lines · H . J . Lu
Quoted 6 lines · Daniel Jacobowitz
Quoted 5 lines

Perl has to be built natively. I uploaded mysql-3.23.36-1.1.src.rpm, perl-5.6.0-12.1.src.rpm, apache-1.3.19-5.src.rpm, mod_perl-1.24_01-2.src.rpm, tcsh-6.10-5.src.rpm and zsh-3.0.8-8.src.rpm. Just installed my RedHat 7.1. Then you can build perl yourself. You may need to build/install the tcsh rpm first.

Quoted 6 lines
Quoted 3 lines

It's not yet available for MIPS (later this week), but MontaVista Journeyman contains the patches to cross-compile Perl. It's not pretty, though.

That is a reason why I didn't bother with cross-compile Perl :-). The next thing on my todo list is to cross compile XFree86 :-(.

If you can get cross-compiling full XFree86, you'll be a hero of all times. It shouldn't be hard to get it with KDriveArchitecture & TinyX enabled.

I was working on it a while ago, and here are few pointers:
Some tools have to be run natively (i.e. xkbcomp), but also need to be installed on target. I din't find a rule that does both. I think new rule is needed.

gcc-3.0 crashes when compiling some parts of Xserver and Xlib, with very obscure bug. Minimal test case I came up with is ~45(!) lines long. Keith filed report to gcc team on my behalf, but there seems to be no responce. I do not know if your gcc has same problem, but someone mentioned similar problem with 2.9x.y series on this list not so long ago.

Hmm... I can't remember any other interesting things at this moment, but if I will, I'll follow up...

Ilya.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.0.4 (GNU/Linux)
Comment: For info see http://www.gnupg.org

iEYEARECAAYFAjtUm18ACgkQtKh84cA8u2ll+QCfSjexRpQ2H7Qa16JYrun/vvVd vCQAoIKb1BRxJ/508SWu9uHEP0okhH00
=kWTa
-----END PGP SIGNATURE-----

#14 lore raw

Re: Updates on RedHat 7.1/mips

Quoted 5 lines · Ilya Volynets

I was working on it a while ago, and here are few pointers:
Some tools have to be run natively (i.e. xkbcomp), but also need to be installed on target. I din't find a rule that does both. I think new rule is needed.

I am aware of those. I want to delay it as much as I can.

Quoted 8 lines

gcc-3.0 crashes when compiling some parts of Xserver and Xlib, with very obscure bug. Minimal test case I came up with is ~45(!) lines long. Keith filed report to gcc team on my behalf, but there seems to be no responce. I do not know if your gcc has same problem, but someone mentioned similar problem with 2.9x.y series on this list not so long ago.

Don't bother with gcc-3.0. I won't use it myself for building X.

H.J.

#15 lore raw

Re: Updates on RedHat 7.1/mips

Em Tue, Jul 17, 2001 at 01:11:46PM -0700, H . J . Lu escreveu:

Quoted 8 lines · Ilya Volynets
Quoted 5 lines

I was working on it a while ago, and here are few pointers:
Some tools have to be run natively (i.e. xkbcomp), but also need to be installed on target. I din't find a rule that does both. I think new rule is needed.

I am aware of those. I want to delay it as much as I can.

recent messages to the XFree86 mailing lists has the recipe to x-compile XFree86, IIRC Keith Packard did the work

Quoted 13 lines
Quoted 8 lines

gcc-3.0 crashes when compiling some parts of Xserver and Xlib, with very obscure bug. Minimal test case I came up with is ~45(!) lines long. Keith filed report to gcc team on my behalf, but there seems to be no responce. I do not know if your gcc has same problem, but someone mentioned similar problem with 2.9x.y series on this list not so long ago.

Don't bother with gcc-3.0. I won't use it myself for building X.

H.J.

Signature · 1 line
                        - Arnaldo
#16 lore raw

Re: Updates on RedHat 7.1/mips

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Those messages are about compiling using TinyX and KDrive, which works with only minor modifications. Thing is, it is not what is really needed.

Quoted 7 lines · Arnaldo Carvalho de Melo

Em Tue, Jul 17, 2001 at 01:11:46PM -0700, H . J . Lu escreveu:

Quoted 6 lines · Ilya Volynets
Quoted 4 lines

I was working on it a while ago, and here are few pointers:
Some tools have to be run natively (i.e. xkbcomp), but also need to be installed on target. I din't find a rule that does both. I think new rule is needed.

Quoted 16 lines
Quoted 1 line

I am aware of those. I want to delay it as much as I can.

recent messages to the XFree86 mailing lists has the recipe to x-compile XFree86, IIRC Keith Packard did the work

Quoted 11 lines
Quoted 6 lines

gcc-3.0 crashes when compiling some parts of Xserver and Xlib, with very obscure bug. Minimal test case I came up with is ~45(!) lines long. Keith filed report to gcc team on my behalf, but there seems to be no responce. I do not know if your gcc has same problem, but someone mentioned similar problem with 2.9x.y series on this list not so long ago.

Don't bother with gcc-3.0. I won't use it myself for building X.

H.J.

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.0.4 (GNU/Linux)
Comment: For info see http://www.gnupg.org

iEYEARECAAYFAjtVChMACgkQtKh84cA8u2nRTACgvPDSNX0E62POj2W+QkntYE9l pzIAnAjjprS4qWgUfELszqT94T+XGV0C
=tJST
-----END PGP SIGNATURE-----

#17 lore raw

Re: Updates on RedHat 7.1/mips

In reply to H . J . Lu
Quoted 9 lines · H . J . Lu
Quoted 2 lines · Carsten Langgaard

Could you add a Perl rpm to you distribution, this also seems to be needed to build the RPMs natively.

Perl has to be built natively. I uploaded mysql-3.23.36-1.1.src.rpm, perl-5.6.0-12.1.src.rpm, apache-1.3.19-5.src.rpm, mod_perl-1.24_01-2.src.rpm, tcsh-6.10-5.src.rpm and zsh-3.0.8-8.src.rpm. Just installed my RedHat 7.1. Then you can build perl yourself. You may need to build/install the tcsh rpm first.

It look like there is a cross dependence, the build of tcsh failed with the following message:

/var/tmp/rpm-tmp.7250: /usr/bin/perl: No such file or directory
error: Bad exit status from /var/tmp/rpm-tmp.7250 (%build)

So tcsh is needed to build perl and perl is needed to build tcsh :-(

Quoted 32 lines
Quoted 7 lines

I also would like to do a cross build, but how do I do that ?
Do I have to change all the spec files, to set the target arch to MIPS, or is there a easier and better way to do that ?
I guess if I just install the SRPMs and the cross toolchain, and try to build out of that I will simply build for the build platform, which is i386.

You need my patched `rpm' to do cross build. You also need some specicial set up. I am enclosng a message of mine. I will see if I can cleanup my cross build environment and upload it.

H.J.
-----

Quoted 10 lines

they work great! Thanks for all your hard work. Now, I would like to be able to build some RPMs as well. I have never cross-built RPMs before. I took the SRPMS for make and tried:

   rpm -ba make.spec --target=mipsel

This did not do anything and built nothing. Is there a FAQ that I can read on cross building RPMS in addition to the documentation on http://www.rpm.org/ ? Do you have any quick pointers? Thanks again.

Although my source rpms do support cross compile, FYI, all my mips/mipsel rpms are cross compiled from ia32 machines, the unpatched rpm, that is /bin/rpm, doesn't support cross compile. In my RedHat 7.1, there are i386 rpm binaries which support cross compile. I have a setup to cross build rpms to mips/mipsel. Make sure your rpm sees

Quoted 11 lines
%__ar                   %{_target_prefix}-linux-ar
%__as                   %{_target_prefix}-linux-as
%__cc                   %{_target_prefix}-linux-gcc
%__cxx                  %{_target_prefix}-linux-c++
%__ld                   %{_target_prefix}-linux-ld
%__nm                   %{_target_prefix}-linux-nm
%__objcopy              %{_target_prefix}-linux-objcopy
%__objdump              %{_target_prefix}-linux-objdump
%__ranlib               %{_target_prefix}-linux-ranlib
%__strip                %{_target_prefix}-linux-strip

How do I do that ?

Quoted 7 lines

and do

# rpm --target=mips --define '_target_prefix mips'

or

Quoted 7 lines
# rpm --target=mipsel --define '_target_prefix mipsel'

BTW, you alao need to rebuild binutils with

# rpm --define 'ENABLE_ALL_TARGETS 1' -ta binutils-2.11.90.0.23.tar.gz

H.J.

--

_    _ ____  ___   Carsten Langgaard   Mailto:[email protected]
|\  /|||___)(___   MIPS Denmark        Direct: +45 4486 5527
| \/ |||    ____)  Lautrupvang 4B      Switch: +45 4486 5555
  TECHNOLOGIES     2750 Ballerup       Fax...: +45 4486 5556
                   Denmark             http://www.mips.com
#18 lore raw

Re: Updates on RedHat 7.1/mips

Quoted 12 lines · Carsten Langgaard
Quoted 9 lines · H . J . Lu
Quoted 2 lines · Carsten Langgaard

Could you add a Perl rpm to you distribution, this also seems to be needed to build the RPMs natively.

Perl has to be built natively. I uploaded mysql-3.23.36-1.1.src.rpm, perl-5.6.0-12.1.src.rpm, apache-1.3.19-5.src.rpm, mod_perl-1.24_01-2.src.rpm, tcsh-6.10-5.src.rpm and zsh-3.0.8-8.src.rpm. Just installed my RedHat 7.1. Then you can build perl yourself. You may need to build/install the tcsh rpm first.

Quoted 8 lines

It look like there is a cross dependence, the build of tcsh failed with the following message:

/var/tmp/rpm-tmp.7250: /usr/bin/perl: No such file or directory
error: Bad exit status from /var/tmp/rpm-tmp.7250 (%build)

So tcsh is needed to build perl and perl is needed to build tcsh :-(

It is ok since the tcsh binary has been built. Just install it to /bin/tcsh and build the perl rpm. You may have to

# rpm --nodeps --force --rebuild perl-xxx.src.rpm

You only have to do those the first time.

H.J.

#19 lore raw

Re: Updates on RedHat 7.1/mips

Quoted 22 lines · H . J . Lu
Quoted 12 lines · Carsten Langgaard
Quoted 9 lines · H . J . Lu
Quoted 2 lines · Carsten Langgaard

Could you add a Perl rpm to you distribution, this also seems to be needed to build the RPMs natively.

Perl has to be built natively. I uploaded mysql-3.23.36-1.1.src.rpm, perl-5.6.0-12.1.src.rpm, apache-1.3.19-5.src.rpm, mod_perl-1.24_01-2.src.rpm, tcsh-6.10-5.src.rpm and zsh-3.0.8-8.src.rpm. Just installed my RedHat 7.1. Then you can build perl yourself. You may need to build/install the tcsh rpm first.

Quoted 8 lines

It look like there is a cross dependence, the build of tcsh failed with the following message:

/var/tmp/rpm-tmp.7250: /usr/bin/perl: No such file or directory
error: Bad exit status from /var/tmp/rpm-tmp.7250 (%build)

So tcsh is needed to build perl and perl is needed to build tcsh :-(

Quoted 6 lines

It is ok since the tcsh binary has been built. Just install it to /bin/tcsh and build the perl rpm. You may have to

# rpm --nodeps --force --rebuild perl-xxx.src.rpm

You only have to do those the first time.

I got through the tcsh and perl build, but now it fails on glibc.

make -s -j2 -C iconvdata others
make[2]: Entering directory `/usr/src/redhat/BUILD/glibc-2.2.3/iconvdata' make[2]: warning: -jN forced in submake: disabling jobserver mode. In file included from 8bit-gap.c:33,

                 from iso8859-15.c:28:

/usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:260:
numeric constant with no digits /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:260: parse error before `nan' /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:260:
numeric constant with no digits /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:260: parse error before nan' /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:260: nan' undeclared here (not in a function) /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:260:
initializer element is not constant /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:260: (near initialization for from_idx[1].idx') /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:261: nan' undeclared here (not in a function) /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:261:
initializer element is not constant /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:261: (near initialization for from_idx[2].idx') /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:262: nan' undeclared here (not in a function) /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:262:
initializer element is not constant /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:262: (near initialization for from_idx[3].idx') /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:263: nan' undeclared here (not in a function) /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:263:
initializer element is not constant /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:263: (near initialization for from_idx[4].idx') /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:264: nan' undeclared here (not in a function) /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:264:
initializer element is not constant /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:264: (near initialization for from_idx[5].idx') /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:265: nan' undeclared here (not in a function) /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:265:
initializer element is not constant /usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.h:265: (near initialization for `from_idx[6].idx')
make[2]: *** [/usr/src/redhat/BUILD/glibc-2.2.3/build-mipsel-linux/iconvdata/iso8859-15.os] Error 1

make[2]: *** Waiting for unfinished jobs....
make[2]: Leaving directory `/usr/src/redhat/BUILD/glibc-2.2.3/iconvdata' make[1]: *** [iconvdata/others] Error 2
make[1]: Leaving directory `/usr/src/redhat/BUILD/glibc-2.2.3'
make: *** [all] Error 2
error: Bad exit status from /var/tmp/rpm-tmp.98017 (%build)

RPM build errors:
Bad exit status from /var/tmp/rpm-tmp.98017 (%build)

Quoted 2 lines

H.J.

--

_    _ ____  ___   Carsten Langgaard   Mailto:[email protected]
|\  /|||___)(___   MIPS Denmark        Direct: +45 4486 5527
| \/ |||    ____)  Lautrupvang 4B      Switch: +45 4486 5555
  TECHNOLOGIES     2750 Ballerup       Fax...: +45 4486 5556
                   Denmark             http://www.mips.com
#20 lore raw

Re: Updates on RedHat 7.1/mips

I am having trouble getting the mipsel packages installed using the installer provided for 7.1.

I have hooked up a second disk to my i386 workstatition that will house the filesystem for my mipsel box. Once everything is installed I will put this disk back in my Qube2 for testing. In the worst case scenario I will need to boot with the 2.0 kernel that came with the cube.

I have the original disk for the Qube2 so it isn't a big problem if it takes 50 attempts. I have a lot of patience ;-)

Am I correct to assume that I need to use the install.i386.hd on my workstation to install the mipsel packages on the second harddrive (hdd in my case)

I have tried this approach using both the Makefile approach and by running the install.i386.hd script.

Traceback (innermost, last):
File "./findrpm", line 5, in ?
import rpm
ImportError: No module named rpm

Does this ring any bells?
The mipsel packages are located in the RPMS directory which is in the same directory as the installer and I edited the Makefile and changed ROOT and REDHAT-ROOT

I wonder if anyone can provide a basic root tarbal which I can use to set up the basics after which i can start adding stuff.

If I get it into a decent state I will probably make a dump of the fs so other people with a Qube (1 or 2) can easily clone it.

I was working to use a 2.4 kernel on a standard Qube but that was a big problem since 2.4 does not compile with the compiler that came with it and the glibc did not have large file support.

A fs that I would like to put on the Qube is XFS which I already use on my own i386 home machines and production machines at work.
Since XFS is also tested on mip64 Irix (IIRC) ai64 PPC ai32 and alpha under linux I expect that it will probably more work but it is more resilient and faster recovering after crashes.

So if anyone can give advice on installing using the toolkit or provide a bootable dump image or root tarbal I would be most grateful. The qube2 comes with a boot loader that understands ext2 and loads the linux kernel it finds on the system it will probably make it easier to boot afterwards.

Cheers
Seth

#21 lore raw

Re: Updates on RedHat 7.1/mips

Quoted 10 lines · Seth Mos

I am having trouble getting the mipsel packages installed using the installer provided for 7.1.

I have hooked up a second disk to my i386 workstatition that will house the filesystem for my mipsel box. Once everything is installed I will put this disk back in my Qube2 for testing. In the worst case scenario I will need to boot with the 2.0 kernel that came with the cube.

Quoted 6 lines

I have the original disk for the Qube2 so it isn't a big problem if it takes 50 attempts. I have a lot of patience ;-)

Am I correct to assume that I need to use the install.i386.hd on my workstation to install the mipsel packages on the second harddrive (hdd in my case)

No. It should be install.mipsel.nfs. install.mipsel.hd is for the native mipsel machine install.

Quoted 7 lines

Traceback (innermost, last):
File "./findrpm", line 5, in ?
import rpm
ImportError: No module named rpm

Does this ring any bells?

You need to install the rpm-python rpm.

Quoted 3 lines

The mipsel packages are located in the RPMS directory which is in the same directory as the installer and I edited the Makefile and changed ROOT and REDHAT-ROOT

Sure.

Quoted 4 lines

I wonder if anyone can provide a basic root tarbal which I can use to set up the basics after which i can start adding stuff.

install.mipsel.nfs is used to create a NFS root tree for mipsel. If you tar it up, you get what you are asking for.

H.J.

#22 lore raw

Re: Updates on RedHat 7.1/mips

Quoted 14 lines · H . J . Lu
Quoted 13 lines · Seth Mos

I am having trouble getting the mipsel packages installed using the installer provided for 7.1.

I have hooked up a second disk to my i386 workstatition that will house the filesystem for my mipsel box. Once everything is installed I will put this disk back in my Qube2 for testing. In the worst case scenario I will need to boot with the 2.0 kernel that came with the cube.

I have the original disk for the Qube2 so it isn't a big problem if it takes 50 attempts. I have a lot of patience ;-)

Quoted 6 lines
Quoted 3 lines

Am I correct to assume that I need to use the install.i386.hd on my workstation to install the mipsel packages on the second harddrive (hdd in my case)

No. It should be install.mipsel.nfs. install.mipsel.hd is for the native mipsel machine install.

Thank you, it worked :-)

Quoted 8 lines
Quoted 6 lines

Traceback (innermost, last):
File "./findrpm", line 5, in ?
import rpm
ImportError: No module named rpm

Does this ring any bells?

You need to install the rpm-python rpm.

And again, thank you.

Quoted 2 lines

install.mipsel.nfs is used to create a NFS root tree for mipsel. If you tar it up, you get what you are asking for.

Will do once it works.
Everythinhg seems to be installed like it should and I copied the 2.0.34 cobalt kernel to /boot on the Qube2. I have enabled the serial console of the Qube2 and see the firmware scroll along.

BOOTLOADER ramcode: selected partition /dev/hda1 Decompressing done
Executing bootloader kernel...
Jump_to_Real_Kernel: disk error, trying BFD again. BOOTLOADER ramcode: selected partition /dev/hdc1

etc.. Qubes don't have the second IDE controller so this is nonsense ;-)
Does anybody know what's missing? Do I need to format the ext2 root fs in a special way? Do I need to pass on other bootoptions and if so. How do I get to a command line prompt of the firmware? I see that the NetBSD people did that to make it boot another kernel.

I thought that the firmware from the Qubes just boot the vmlinux.gz image that it finds in the /boot directory on hda1?

Any help appreciated.

Cheers

--
Seth
Every program has two purposes one for which
it was written and another for which it wasn't
I use the last kind.