Skip to contentSkip to conversation

PROBLEM : OHCI1394 module crashes linux with 2.4.9 (and 2.4.8 ?)

DISCUSSION Pierre JUHEN 1 participant 1 message Aug 22, 2001

lore
Share & tools
lore

Pierre JUHEN

author
#0 lore raw

[1.] OHCI1394 module crashes linux with 2.4.9 (and 2.4.8)

[2.] "modprobe ohci1394" causes the system to crash instantaneously with kernel 2.4.9 (same configuration with 2.4.6 was OK), either on boot or manually.
No trace is written in /var/log/messages. Two other people reported an analog problem with 2.4.8 on comp.linux.hardware.

[3.] OHCI1394 module crash kernel

[4.] Linux version 2.4.9 ([email protected]) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-81)) #2 dim aoû 19 19:02:56 CEST 2001

[5.]

[6.] modprobe ohci1394

[7.]
[7.1] Software

Linux pierre.juhen 2.4.9 #2 dim aoû 19 19:02:56 CEST 2001 i686 unknown

Gnu C                  2.96
Gnu make               3.79.1
binutils               2.10.91.0.2
util-linux             2.10s
mount                  2.11b
modutils               2.4.2
e2fsprogs              1.19
reiserfsprogs          3.x.0b
pcmcia-cs              3.1.19
PPP                    2.4.0
isdn4k-utils           3.1pre1
Linux C Library        2.2.2
Dynamic linker (ldd)   2.2.2
Procps                 2.0.7
Net-tools              1.56
Console-tools          0.3.3
Sh-utils               2.0

[7.2] Processor

processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 5
model name : Pentium II (Deschutes)
stepping : 2
cpu MHz : 400.914
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca
cmov pat pse36 mmx fxsr
bogomips : 799.53

[7.3] modules

pppoatm                 2832   1
ppp_generic            14816   3 [pppoatm]
slhc                    5024   0 [ppp_generic]
usb-uhci               21088   0 (unused)
speedtch               11568   3
snd-seq-midi            3600   0 (unused)
snd-seq-midi-event      3264   0 [snd-seq-midi]
snd-seq                41792   0 [snd-seq-midi snd-seq-midi-event]
snd-card-ens1371        2288   0
snd-ens1371             9664   0 [snd-card-ens1371]
snd-rawmidi            10080   0 [snd-seq-midi snd-ens1371]
snd-seq-device          4016   0 [snd-seq-midi snd-seq snd-rawmidi]
snd-pcm                31520   0 [snd-ens1371]
snd-timer               8560   0 [snd-seq snd-pcm]
snd-ac97-codec         25024   0 [snd-ens1371]
snd-mixer              24608   0 [snd-ens1371 snd-ac97-codec]
snd                    34896   1 [snd-seq-midi snd-seq-midi-event
snd-seq snd-card-ens1371 snd-ens1371 snd-rawmidi snd-seq-device snd-pcm
snd-timer snd-ac97-codec snd-mixer]
soundcore               4144   2 [snd]
3c509                   6224   1 (autoclean)
ipchains               35904   0 (unused)
nls_iso8859-1           2880   1 (autoclean)
nls_cp437               4384   1 (autoclean)
vfat                    9424   1 (autoclean)
fat                    32320   0 (autoclean) [vfat]
usbcore                50272   1 [usb-uhci speedtch]

[7.4] iomem / ioports

00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000cdfff : Extension ROM
000f0000-000fffff : System ROM
00100000-07feffff : System RAM
00100000-001fb813 : Kernel code
001fb814-00257b7f : Kernel data
07ff0000-07ff2fff : ACPI Non-volatile Storage 07ff3000-07ffffff : ACPI Tables
d8000000-dbffffff : Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge dc000000-deffffff : PCI Bus #01
dc000000-dc003fff : Matrox Graphics, Inc. MGA G200 AGP dd000000-dd7fffff : Matrox Graphics, Inc. MGA G200 AGP
df000000-dfffffff : PCI Bus #01
df000000-dfffffff : Matrox Graphics, Inc. MGA G200 AGP
e1000000-e1003fff : PCI device 104c:8020 (Texas Instruments) e1004000-e1004fff : Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895
e1004000-e1004fff : aic7xxx
e1005000-e10057ff : PCI device 104c:8020 (Texas Instruments) e1006000-e1006fff : Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 (#2)
e1006000-e1006fff : aic7xxx
ffff0000-ffffffff : reserved

0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide0
0280-028f : 3c509
02f8-02ff : serial(auto)
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
4000-403f : Intel Corporation 82371AB PIIX4 ACPI 5000-501f : Intel Corporation 82371AB PIIX4 ACPI e000-e01f : Intel Corporation 82371AB PIIX4 USB
e000-e01f : usb-uhci
e400-e43f : Ensoniq ES1371 [AudioPCI-97]
e400-e43f : Ensoniq AudioPCI
e800-e8ff : Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 ec00-ecff : Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 (#2) f000-f00f : Intel Corporation 82371AB PIIX4 IDE

[7.5] PCI

00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+

        Latency: 32
        Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [a0] AGP version 1.0
                Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
                Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000f000-00000fff
Memory behind bridge: dc000000-deffffff
Prefetchable memory behind bridge: df000000-dfffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+

00:07.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 32
        Region 4: I/O ports at f000 [size=16]

00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 32
        Interrupt: pin D routed to IRQ 11
        Region 4: I/O ports at e000 [size=32]

00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9

00:0f.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8020 (prog-if 10 [OHCI])
Subsystem: Pinnacle Systems Inc.: Unknown device 000e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 32 (500ns min, 1000ns max), cache line size 08
        Interrupt: pin A routed to IRQ 15
        Region 0: Memory at e1005000 (32-bit, non-prefetchable)
[size=2K]
        Region 1: Memory at e1000000 (32-bit, non-prefetchable)

[size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev
02)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V,
AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort+ <MAbort+ >SERR- <PERR-
Latency: 64 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e400 [size=64]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0+,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:14.0 SCSI storage controller: Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 (rev 04)

        Subsystem: Adaptec AHA-2940U/2940UW Dual AHA-394xAU/AUW/AUWD

AIC-7895B
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 32 (2000ns min, 2000ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at e800 [disabled] [size=256]
        Region 1: Memory at e1004000 (32-bit, non-prefetchable)

[size=4K]
Expansion ROM at e0000000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:14.1 SCSI storage controller: Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 (rev 04)

        Subsystem: Adaptec AHA-2940U/2940UW Dual AHA-394xAU/AUW/AUWD

AIC-7895B
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 32 (2000ns min, 2000ns max)
        Interrupt: pin B routed to IRQ 15
        Region 0: I/O ports at ec00 [disabled] [size=256]
        Region 1: Memory at e1006000 (32-bit, non-prefetchable)

[size=4K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP (rev 01) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. MGA-G200 AGP
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 32 (4000ns min, 8000ns max), cache line size 08
        Interrupt: pin A routed to IRQ 15
        Region 0: Memory at df000000 (32-bit, prefetchable) [size=16M]
        Region 1: Memory at dc000000 (32-bit, non-prefetchable)
[size=16K]
        Region 2: Memory at dd000000 (32-bit, non-prefetchable)

[size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x2

[7.6] SCSI

Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: MATSHITA Model: CD-R CW-7502 Rev: 4.10
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: IBM Model: DDRS-34560W Rev: S97B
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 10 Lun: 00
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02

[7.7] ieee1394 card is a Pinnacle Studio DV

[8.] Workaround : do not load module iee1394