AMD 760 (761?) AGP
Hello,
What is current status of support for AMD 760 (or is this 761?) AGP bridge? Current agpgart doesn't seem to work when forced to load.
Here's output from lspci -vvv and /proc/pci, dunno about lspci, but both are AGP 4x. Also some id information could be added for the ATI. It's ATI Radeon VE DDR (QY?, 186 Mhz).
00:00.0 Host bridge: Advanced Micro Devices [AMD]: Unknown device 700e (rev
13)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 32 Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M] Region 1: Memory at f7800000 (32-bit, prefetchable) [size=4K] Region 2: I/O ports at e000 [disabled] [size=4] Capabilities: [a0] AGP version 2.0 Status: RQ=15 SBA+ 64bit- FW+ Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Advanced Micro Devices [AMD]: Unknown device 700f (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: e7000000-e7dfffff Prefetchable memory behind bridge: e7f00000-f77fffff BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5159 (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 013a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), cache line size 08 Interrupt: pin A routed to IRQ 9 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at d800 [size=256] Region 2: Memory at e7000000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at e7fe0000 [disabled] [size=128K] Capabilities: [58] AGP version 2.0 Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none> Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bus 0, device 0, function 0:
Host bridge: Advanced Micro Devices [AMD] AMD-760 [Irongate] System
Controller (rev 19).
Master Capable. Latency=32.
Prefetchable 32 bit memory at 0xf8000000 [0xfbffffff].
Prefetchable 32 bit memory at 0xf7800000 [0xf7800fff].
I/O at 0xe000 [0xe003]. Bus 0, device 1, function 0:
PCI bridge: Advanced Micro Devices [AMD] AMD-760 [Irongate] AGP Bridge
(rev 0).
Master Capable. No bursts. Min Gnt=8.
Bus 1, device 5, function 0:
VGA compatible controller: PCI device 1002:5159 (ATI Technologies Inc)
(rev 0).
IRQ 9.
Master Capable. Latency=64. Min Gnt=8.
Prefetchable 32 bit memory at 0xe8000000 [0xefffffff].
I/O at 0xd800 [0xd8ff].
Non-prefetchable 32 bit memory at 0xe7000000 [0xe700ffff].Signature · 2 lines
PGP key fingerprint: 161D 6FED 6A92 39E2 EB5B 39DD A4DE 63EB C216 1E4B Available at PGP keyservers
If you have it as a module try loading it with agp_try_unsupported=1. If its not a module try appending it to lilo. I have that chipset and everything works fine with those options. I have a GF2U however not a Radeon. I can get 4x working with side band addressing and fast write.
Steven
Quoted 78 lines · Jussi Laako
Hello,
What is current status of support for AMD 760 (or is this 761?) AGP bridge? Current agpgart doesn't seem to work when forced to load.
Here's output from lspci -vvv and
/proc/pci, dunno about lspci, but both are AGP 4x. Also some id information could be added for the ATI. It's ATI Radeon VE DDR (QY?, 186 Mhz).00:00.0 Host bridge: Advanced Micro Devices [AMD]: Unknown device 700e (rev
13)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-Latency: 32 Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M] Region 1: Memory at f7800000 (32-bit, prefetchable) [size=4K] Region 2: I/O ports at e000 [disabled] [size=4] Capabilities: [a0] AGP version 2.0 Status: RQ=15 SBA+ 64bit- FW+ Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>00:01.0 PCI bridge: Advanced Micro Devices [AMD]: Unknown device 700f (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: e7000000-e7dfffff Prefetchable memory behind bridge: e7f00000-f77fffff BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5159 (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 013a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-Latency: 64 (2000ns min), cache line size 08 Interrupt: pin A routed to IRQ 9 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at d800 [size=256] Region 2: Memory at e7000000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at e7fe0000 [disabled] [size=128K] Capabilities: [58] AGP version 2.0 Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none> Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-Bus 0, device 0, function 0:
Host bridge: Advanced Micro Devices [AMD] AMD-760 [Irongate] System
Controller (rev 19).Master Capable. Latency=32. Prefetchable 32 bit memory at 0xf8000000 [0xfbffffff]. Prefetchable 32 bit memory at 0xf7800000 [0xf7800fff]. I/O at 0xe000 [0xe003].Bus 0, device 1, function 0:
PCI bridge: Advanced Micro Devices [AMD] AMD-760 [Irongate] AGP Bridge
(rev 0).
Master Capable. No bursts. Min Gnt=8.Bus 1, device 5, function 0:
VGA compatible controller: PCI device 1002:5159 (ATI Technologies Inc)
(rev 0).IRQ 9. Master Capable. Latency=64. Min Gnt=8. Prefetchable 32 bit memory at 0xe8000000 [0xefffffff]. I/O at 0xd800 [0xd8ff]. Non-prefetchable 32 bit memory at 0xe7000000 [0xe700ffff].
Quoted 5 lines · Steven Spence
If you have it as a module try loading it with agp_try_unsupported=1. If its not a module try appending it to lilo. I have that chipset and everything works fine with those options. I have a GF2U however not a Radeon. I can get 4x working with side band addressing and fast write.
Yes, I did try that and result is deadlock without video signal. Without AGP it works fine. XFree86 and dri/drm driver is the latest CVS version. (With or without dri enabled)
- Jussi Laako
Signature · 2 lines
PGP key fingerprint: 161D 6FED 6A92 39E2 EB5B 39DD A4DE 63EB C216 1E4B Available at PGP keyservers
Quoted 5 lines · Steven Spence
If you have it as a module try loading it with agp_try_unsupported=1. If its not a module try appending it to lilo. I have that chipset and everything
works fine with those options. I have a GF2U however not a Radeon. I can get 4x working with side band addressing and fast write.
I have an Asus A7M266 with a AMD 761 chipset. I can get agpgart to work with agp_try_unsupported=1, and it works fine, but I only get AGP 1x support.
Signature · 2 lines
Met vriendelijke groet / with kind regards, Guus Sliepen <[email protected]>
Quoted 11 lines · Guus Sliepen
Quoted 5 lines · Steven Spence
If you have it as a module try loading it with agp_try_unsupported=1. If its not a module try appending it to lilo. I have that chipset and everything
works fine with those options. I have a GF2U however not a Radeon. I can get 4x working with side band addressing and fast write.I have an Asus A7M266 with a AMD 761 chipset. I can get agpgart to work with agp_try_unsupported=1, and it works fine, but I only get AGP 1x support.
I also have an Asus A7M266, and my GF3 (Asus V8200 Deluxe) works just fine even without the agp_try_unsupported=1 option (both with the nv driver and the binary only NVidia driver)..
Best regards,
Jesper Juhl
Quoted 3 lines · Jussi Laako
Yes, I did try that and result is deadlock without video signal. Without AGP it works fine. XFree86 and dri/drm driver is the latest CVS version. (With or without dri enabled)
For a workaround until it is fixed properly, find RADEON_SOFT_RESET_HDP
in your kernel radeon driver source and kill it. Possibly XFree86 CVS source is fixed already, but anyway you need to change and compile some modules from XFree86 source too and install them to where the X server will find them.
Check out dri.sf.net -> project -> bug [ #221904 ] Radeon + AMD
Irongate.
Signature · 2 lines
[email protected] http://www.iki.fi/hyvatti/ +358 40 5011222 echo 'movl $36,%eax;int $128;movl $0,%ebx;movl $1,%eax;int $128'|as -o/bin/sync