Skip to contentSkip to conversation

I'd like a bit of help on tracing my oops

DISCUSSION Christopher Friesen 2 participants 2 messages Nov 12, 2001

lore
Share & tools
lore
#0 lore raw

I've been doing some work on customizing the 2.2 kernel to add class-based scheduling. It all seems to be going fairly well except that today for the first time I started seeing kernel panics. It appears to be in the setscheduler() routine, but I'm looking for some pointers on tracking it down.

The output in /var/log/messages is as follows:

Nov 12 16:02:59 pcary1k7 kernel: Unable to handle kernel NULL pointer
dereference at virtual address 0000009c (error 40000000)
Nov 12 16:02:59 pcary1k7 kernel: NIP: 90016720 XER: 00000000 LR: 900166D8 REGS:
9bfa5d30 TRAP: 3100
Nov 12 16:02:59 pcary1k7 kernel: MSR: 00001032 [IRDRME]
Nov 12 16:02:59 pcary1k7 kernel: TASK = 9bfa4000[651] 'setsched' mm->pgd
ad589000 Last syscall: 156
Nov 12 16:02:59 pcary1k7 kernel: last math 9bfa4000
Nov 12 16:02:59 pcary1k7 kernel: GPR00: 000001C4 9BFA5E00 9BFA4000 00000001
00008000 00000004 9BFA5E08 00000000
Nov 12 16:02:59 pcary1k7 kernel: GPR08: 80000548 00000000 90016958 00000000
42242242 10018F0C 00000000 100B3E50
Nov 12 16:02:59 pcary1k7 kernel: GPR16: 10010000 10040000 00000000 00000000
00009032 0BFA5E40 0BFA4000 90004250
Nov 12 16:02:59 pcary1k7 kernel: GPR24: 90003ED0 10000BC8 2802678C 00000004
FFFFFFF2 00000008 00000273 9BFA5E00
Nov 12 16:02:59 pcary1k7 kernel: Call backtrace:
Nov 12 16:02:59 pcary1k7 kernel: 00000000 90016970 90003F24 10000A38 0FE4373C
00000000
Nov 12 16:02:59 pcary1k7 kernel: Kernel panic: kernel access of bad area pc

90016720 lr 900166d8 address 9C tsk setsched/651

Running ksymoops on that file gives:

Nov 12 16:02:59 pcary1k7 kernel: Unable to handle kernel NULL pointer
dereference at virtual address 0000009c (error 40000000)
Nov 12 16:02:59 pcary1k7 kernel: NIP: 90016720 XER: 00000000 LR: 900166D8 REGS:
9bfa5d30 TRAP: 3100
Nov 12 16:02:59 pcary1k7 kernel: MSR: 00001032 [IRDRME]
Nov 12 16:02:59 pcary1k7 kernel: TASK = 9bfa4000[651] 'setsched' mm->pgd
ad589000 Last syscall: 156
Nov 12 16:02:59 pcary1k7 kernel: last math 9bfa4000
Nov 12 16:02:59 pcary1k7 kernel: GPR00: 000001C4 9BFA5E00 9BFA4000 00000001
00008000 00000004 9BFA5E08 00000000
Nov 12 16:02:59 pcary1k7 kernel: GPR08: 80000548 00000000 90016958 00000000
42242242 10018F0C 00000000 100B3E50
Nov 12 16:02:59 pcary1k7 kernel: GPR16: 10010000 10040000 00000000 00000000
00009032 0BFA5E40 0BFA4000 90004250
Nov 12 16:02:59 pcary1k7 kernel: GPR24: 90003ED0 10000BC8 2802678C 00000004
FFFFFFF2 00000008 00000273 9BFA5E00
Nov 12 16:02:59 pcary1k7 kernel: Call backtrace:
Nov 12 16:02:59 pcary1k7 kernel: 00000000 90016970 90003F24 10000A38 0FE4373C
00000000
Nov 12 16:02:59 pcary1k7 kernel: Kernel panic: kernel access of bad area pc

90016720 lr 900166d8 address 9C tsk setsched/651 Warning, Code line not seen, dumping what data is available

Quoted 1 line
Quoted 1 line

NIP: 90016720 <setscheduler+c0/2f8>

Trace: 00000000 Before first symbol
Trace: 90016970 <sys_sched_setscheduler+18/30>
Trace: 90003f24 <syscall_ret_1+0/a0>
Trace: 10000a38 Before first symbol
Trace: 0fe4373c Before first symbol
Trace: 00000000 Before first symbol

Quoted 1 line
Quoted 1 line

NIP: 90016720 <setscheduler+c0/2f8>

At this point I'm not entirely certain how to track down the exact line of code where it's dying. If I am reading it right, then the program counter was at 90016720, is this correct? Then disassembling vmlinux in gdb should give me the instruction corresponding to that address, at which point I need to correlate that to the actual code to figure out what's happening, correct? Is it expected that disassembling vmlinux will give the same code as doing a make <file.s> in the linux tree?

Thanks,

Chris

Signature · 4 lines
Chris Friesen                    | MailStop: 043/33/F10  
Nortel Networks                  | work: (613) 765-0557
3500 Carling Avenue              | fax:  (613) 765-2986
Nepean, ON K2H 8E9 Canada        | email: [email protected]
#1 lore raw
Quoted 8 lines · Christopher Friesen

At this point I'm not entirely certain how to track down the exact line of code where it's dying. If I am reading it right, then the program counter was at 90016720, is this correct? Then disassembling vmlinux in gdb should give me the instruction corresponding to that address, at which point I need to correlate that to the actual code to figure out what's happening, correct? Is it expected that disassembling vmlinux will give the same code as doing a make <file.s> in the linux tree?

What I like to do is to add -g to CFLAGS in Makefile. Then you can do an "objdump -S vmlinux" and see the original source interspersed with the disassembled code.

Chris