Booting from IDE
If you feel lucky, you can also reserve space on your disk for the kernel - either in a separate partition, or outside the area used by your current partitions. The YAMON 02.02 or later can read the kernel directly from disk and execute it.
I do this on my Malta board with one disk.
/Hartvig
Quoted 30 lines · Dan Temple
I guess you're installing as per:
ftp://ftp/pub/linux/mips/installation/redhat7.1/INSTALL
(If not, you might want to upgrade to that version).
YAMON can't read the disk file system, so you have to TFTP the kernel to memory from a remote filesystem, and then run it. The instructions are in the above file under "Booting linux on the target".
The latest version (2.02) of YAMON can read and write blocks from an IDE device (not a filesystem) so you could install a CompactFlash card and use that to store the kernel if you don't want to TFTP each time.
There is also a $start environment variable if you want to auto-boot.
/Dan
Quoted 14 lines · Nitin
Hi,
I have a very basic query. I have a MIPS Malta board. I attached a IDE hard disk to it and installed linux as per the instructions. At the end of the installation, system rebooted and control gone to the board monitor program(Yamon). How can I get the linux prompt? Do I need to write an application program which will read boot sector from hard disk,store it in memory and pass on control to that particular location?(If yes, is such application already available?) Or is there a other way of doing it.
Thanks,
Nitin
Hi,
I have a very basic query. I have a MIPS Malta board. I attached a IDE hard disk to it and installed linux as per the instructions. At the end of the installation, system rebooted and control gone to the board monitor program(Yamon). How can I get the linux prompt? Do I need to write an application program which will read boot sector from hard disk,
store it in memory and pass on control to that particular location?(If yes, is such application already available?) Or is there a other way of doing it.
Thanks,
Nitin
I guess you're installing as per:
ftp://ftp/pub/linux/mips/installation/redhat7.1/INSTALL
(If not, you might want to upgrade to that version).
YAMON can't read the disk file system, so you have to TFTP the kernel to memory from a remote filesystem, and then run it. The instructions are in the above file under "Booting linux on the target".
The latest version (2.02) of YAMON can read and write blocks from an IDE device (not a filesystem) so you could install a CompactFlash card and use that to store the kernel if you don't want to TFTP each time.
There is also a $start environment variable if you want to auto-boot.
/Dan
Quoted 14 lines · Nitin
Hi,
I have a very basic query. I have a MIPS Malta board. I attached a IDE hard disk to it and installed linux as per the instructions. At the end of the installation, system rebooted and control gone to the board monitor program(Yamon). How can I get the linux prompt? Do I need to write an application program which will read boot sector from hard disk,store it in memory and pass on control to that particular location?(If yes, is such application already available?) Or is there a other way of doing it.
Thanks,
Nitin
Signature · 5 lines
Dan Temple, Eng. Mgr. Tel: +45-44865512 MIPS Denmark Fax: +45-44865556 Lautrupvang 4B mailto:[email protected] DK-2750 Ballerup http://www.mips.com Denmark
Another possibility is to replace YAMON with RedBoot.
http://sources.redhat.com/redboot/
RedBoot can load the kernel image directly from an ext2 filesystem on an IDE drive. You can also use it to put the kernel image and JFFS filesystem in flash for a diskless boot.
--Mark
Quoted 43 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Hartvig Ekner writes:
If you feel lucky, you can also reserve space on your disk for the kernel - either in a separate partition, or outside the area used by your current partitions. The YAMON 02.02 or later can read the kernel directly from disk and execute it.
I do this on my Malta board with one disk.
/Hartvig
Quoted 30 lines · Dan Temple
I guess you're installing as per:
ftp://ftp/pub/linux/mips/installation/redhat7.1/INSTALL
(If not, you might want to upgrade to that version).
YAMON can't read the disk file system, so you have to TFTP the kernel to memory from a remote filesystem, and then run it. The instructions are in the above file under "Booting linux on the target".
The latest version (2.02) of YAMON can read and write blocks from an IDE device (not a filesystem) so you could install a CompactFlash card and use that to store the kernel if you don't want to TFTP each time.
There is also a $start environment variable if you want to auto-boot.
/Dan
Quoted 14 lines · Nitin
Hi,
I have a very basic query. I have a MIPS Malta board. I attached a IDE hard disk to it and installed linux as per the instructions. At the end of the installation, system rebooted and control gone to the board monitor program(Yamon). How can I get the linux prompt? Do I need to write an application program which will read boot sector from hard disk,store it in memory and pass on control to that particular location?(If yes, is such application already available?) Or is there a other way of doing it.
Thanks,
Nitin
Thanks Dan, Hartvig and Mark.
I could get the linux prompt according to the instruction given in the Install file Dan has suggested. I will update my Yamon and try auto booting also.
-Nitin
Quoted 52 lines · Mark Salter
Another possibility is to replace YAMON with RedBoot.
http://sources.redhat.com/redboot/
RedBoot can load the kernel image directly from an ext2 filesystem on an IDE drive. You can also use it to put the kernel image and JFFS filesystem in flash for a diskless boot.
--Mark
Quoted 42 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Hartvig Ekner writes:
If you feel lucky, you can also reserve space on your disk for the kernel - either in a separate partition, or outside the area used by your current partitions. The YAMON 02.02 or later can read the kernel directly from disk and execute it.
I do this on my Malta board with one disk.
/Hartvig
Quoted 30 lines · Dan Temple
I guess you're installing as per:
ftp://ftp/pub/linux/mips/installation/redhat7.1/INSTALL
(If not, you might want to upgrade to that version).
YAMON can't read the disk file system, so you have to TFTP the kernel to memory from a remote filesystem, and then run it. The instructions are in the above file under "Booting linux on the target".
The latest version (2.02) of YAMON can read and write blocks from an IDE device (not a filesystem) so you could install a CompactFlash card and use that to store the kernel if you don't want to TFTP each time.
There is also a $start environment variable if you want to auto-boot.
/Dan
Quoted 14 lines · Nitin
Hi,
I have a very basic query. I have a MIPS Malta board. I attached a IDE hard disk to it and installed linux as per the instructions. At the end of the installation, system rebooted and control gone to the board monitor program(Yamon). How can I get the linux prompt? Do I need to write an application program which will read boot sector from hard disk,store it in memory and pass on control to that particular location?(If yes, is such application already available?) Or is there a other way of doing it.
Thanks,
Nitin