Skip to contentSkip to conversation

SCSI + IDE = HANG

DISCUSSION Douglas Gilbert 2 participants 2 messages Feb 2, 2002 – Feb 3, 2002

lore
Share & tools
lore
#0 lore raw
Quoted 8 lines · Keith Baker

I have had a few random hangs with my machine since I added a maxtor 27 gig IDE drive to it. I kept trying different combinations of bus positions etc. I figured it was flacky hardware or something. I added the drive in the early 2.4 series. Recently I became slightly suspicious of my Adaptec 2940U2W after reading all of the problems it had in the early 2.4. So I upgraded the bios and got kernel 2.4.17. Though the problem seems diminished it is certainly not gone...

Quoted 7 lines

Now for the kicker... I found a 99% guarenteed way to hard lock my box. I tried ripping two cds at a time. One on the ide bus and one on the scsi. Just a note the data is being stored to the maxtor 27 gig mentioned above. The reason I point to the IDE + SCSI combo is that I can do two scsi cdroms ripping to the maxtor and it works much more reliably. I am under the impression that IDE CDROMs use the ide bus quite heavily under ripping...

Keith,
Does turning off (or reducing the speed of) DMA to the IDE cdrom with either one of these commands help?

    hdparm -d0 -c1 /dev/hdd 
    hdparm -d 1 -X 34 /dev/hdd

[This assumes the IDE cdrom is connected to /dev/hdd.]

Doug Gilbert

#1 lore raw

the first command sucseeded and my machine seems to be stable with it... I then tried the second command and got this...

/dev/hdd:
setting using_dma to 1 (on)
setting xfermode to 34 (multiword DMA mode2) HDIO_DRIVE_CMD(setxfermode) failed: Input/output error
using_dma = 1 (on)

I noted that it turned dma back on and left 32 bit alone... but the xfer mode seemed to fail... it does jhowever still seem stable... thoughts?

Keith Baker
Email: [email protected]

Life is a sexually transmitted disease with 100% mortality.

Quoted 31 lines · Douglas Gilbert
Quoted 8 lines · Keith Baker

I have had a few random hangs with my machine since I added a maxtor 27 gig IDE drive to it. I kept trying different combinations of bus positions etc. I figured it was flacky hardware or something. I added the drive in the early 2.4 series. Recently I became slightly suspicious of my Adaptec 2940U2W after reading all of the problems it had in the early 2.4. So I upgraded the bios and got kernel 2.4.17. Though the problem seems diminished it is certainly not gone...

Quoted 7 lines

Now for the kicker... I found a 99% guarenteed way to hard lock my box. I tried ripping two cds at a time. One on the ide bus and one on the scsi. Just a note the data is being stored to the maxtor 27 gig mentioned above. The reason I point to the IDE + SCSI combo is that I can do two scsi cdroms ripping to the maxtor and it works much more reliably. I am under the impression that IDE CDROMs use the ide bus quite heavily under ripping...

Keith,
Does turning off (or reducing the speed of) DMA to the IDE cdrom with either one of these commands help?

    hdparm -d0 -c1 /dev/hdd 
    hdparm -d 1 -X 34 /dev/hdd

[This assumes the IDE cdrom is connected to /dev/hdd.]

Doug Gilbert
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/