Athlon Optimization Problem
Hello again.
Just as followup... I was trying to find a minimum deviation from BIOS settigns to make Soyo Dragon Plus stable:
In KT266A northbridge 1106:3099:
Reg[0x75] = 0x07; // this was set to 0x01 by BIOS Reg[0x76] = 0x00; // this was 0x10
Without this change I had filesystem corruptions during kernel compilation...
Unfortunately, some issues with Zoran ZR36067 based cards are still open. VIA wrote me that they are looking for DC10plus card to test it in their labs...
BTW, with the settings above DC10plus behaves much better in Linux, though I can not say that it is fully functional now:
I don't have freezes anymore, but it seems that sometimes the kernel itself gets corrupted after running DC10plus related stuff: some programs, like ls, crash immediately with segfaults but after reboot filesystems are clean (fsck.ext3 -f does not report any errors). Also, there are some indications of PCI malfunction: to catch PCI errors I have added, to the ZR36067 driver, test of PCI status register on DC10plus every IRQ and it sometimes reports about every PCI error possible at once (master and target aborts, parity error, etc.). I don't think it is ever possible, therefore I suspect problem with CPU-PCI path (NB-Vlink-SB-PCI). Right after such an error message I have these kernel problems... Perhaps, PCI DMA gets rerouted to the wrong place in memory... Hmm, can the hardware be so broken to make it possible?
In Windows the situation with DC10plus card does not change much even after the same KT266A settings are applied: the same lockups as before. However, now I have removed well known George Breeze PCI latency patch (which also sets NB latency time to 0), and still don't have filesystem corruptions...
Please, note that settings above might be OK for my motherboard but may cause problems for others. I have received very mixed reports about both: my PCI latency patch and these new settings, so I can not recommend to include it to the kernel...
Another important information: with these settings my system is extremely stable if I don't touch Zoran 36067 card, but if I run anything related with this video capture hardware, I have problems... For those who may think about broken
DC10plus: the card works great in a system with Intel 430TX, and I also have reports from others about the same problems.
--
Serguei Miridonov
Quoted 9 lines · Serguei Miridonov
Just as followup... I was trying to find a minimum deviation from BIOS settigns to make Soyo Dragon Plus stable:
In KT266A northbridge 1106:3099:
Reg[0x75] =
0x07; // this was set to0x01by BIOS Reg[0x76] =0x00; // this was0x10
Without this change I had filesystem corruptions during kernel compilation...
[MODEL]=VT8366 (KT266) Athlon NB
[VID]=1106:VIA
[DID]=3099:Host to PCI Bridge
[75:7]=Arbitration Mode 0=REQ-based 1=Frame-based
(75:6)=CPU Latency Timer read only
(75:5)=(same as above)
(75:4)=(same as above)
[75:3]=(Reserved)
[75:2]=PCI Master Bus Time-Out 000=Disable [75:1]=001=1x32 PCICLKs 010=2x32 PCICLKs [75:0]=011=3x32 PCICLKs ... 111=7x32 PCICLKs
Note: other doc I have (for KT266A) says 75.3 is used for PCI Master Bus Time-Out too (thus max timeout is 1111 = 15x32 PCICLKs)
[76:7]=I/O Port 22 Enable
[76:6]=(Reserved)
[76:5]=Master Priority Rotation 0x=every PCI master grant
[76:4]=10=after every 2 PCI 11=after every 3 PCI
[76:3]=REQn# to REQ4# Mapping 00=REQ4# 01=REQ0#
[76:2]=10=REQ1# 11=REQ2#
[76:1]=(Reserved)
[76:0]=REQ4# Is High Priority 0=disable 1=enable
KT266A doc says:
76.5-4: Master Priority Rotation: 00 disable
01 every PCI master grant
10 every 2 PCI master grant
11 every 3 PCI master grant
--
vda